Enable the bootcount driver for am335x in general.  We leave adding a
bootlimit and altbootcmd to the environment to the board ports.
Signed-off-by: NTom Rini <trini@ti.com>

The RTC IP block here provides 3 scratch registers.  Currently when
using DeepSleep on am335x the scratch0/1 registers are used so moving
ourself to scratch2 makes cooperation easier.
Signed-off-by: NTom Rini <trini@ti.com>

Create a common header file for the RTC IP block that is shared between
davinci and am33xx.
Signed-off-by: NTom Rini <trini@ti.com>

We shouldn't rely on a define to hide this cast for us.
Signed-off-by: NTom Rini <trini@ti.com>

Remove Prodrive pdnb3 board (including the scpu variant) support
from mainline. As its unmaintained and not needed any more for
quite some time.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>

Zynq lowlevel_init() was implemented in C but stack
pointer is setup after function call in _main().
Move architecture setup to arch_cpu_init() which is call
as the first function in board_init_f() which
already have correct stack pointer.
Reported-by: NSven Schwermer <sven.schwermer@tuhh.de>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Signed-off-by: NTom Rini <trini@ti.com>

The patch:
"blackfin: Move blackfin watchdog driver out of the blackfin arch folder."
(sha1: e9a389a1)
changed hw_watchdog_init() prototype which didn't match
with Microblaze one.
This patch fixes the driver and Microblaze initialization.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This bug was introduced by:
"Add GPL-2.0+ SPDX-License-Identifier to source files"
(sha1: 1a459660)
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

commit 39ac3447 ("cmd_mtdparts: use 64
bits for flash size, partition size & offset") introduced warnings
in a couple places due to printf formats or pointer casting.

This patch fixes the warnings pointed out here:
http://lists.denx.de/pipermail/u-boot/2013-October/164981.htmlSigned-off-by: NScott Wood <scottwood@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Tom Rini <trini@ti.com>

If dout buffer is not 32 bit-aligned or data to transmit is not multiple
of 32 bit the read data pointer is already incremented on single byte reads.
Signed-off-by: NTimo Herbrecher <t.herbrecher@gateware.de>
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

As the spi flash transfer to multiple parts, it is forgot to add
Atmel AT25DF321 spi flash support, which broken several Atmel EK
boards which this chip. So, add it
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

Added GPL-2.0+ SPDX-License-Identifier for missed spi
source files.
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

Added GPL-2.0+ SPDX-License-Identifier for missed sf
source files.
Signed-off-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: NBo Shen <voice.shen@atmel.com>

- Add comments.
- Renamed few macros.
- Add tabs.
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: NBo Shen <voice.shen@atmel.com>

Unified the bank_sel calculation code for erase and
write ops.
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

python used in buildman doesn't need to be placed in
/usr/bin/python, So use env to ensure that the interpreter
will pick the python from environment.

Usefull with several versions of python's installed on system.
Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NTom Rini <trini@ti.com>

Pass a valid cmdtp into do_tftpb(), do_ext2load(), and do_get_fat(), to
avoid possible crashes due to null pointer dereferencing.

Commit d7884e04 does not go far enough.
There is still at least one call chain that can result in a crash.

The do_tftpb(), do_ext2load(), and do_get_fat() functions expect a valid
cmdtp.  Passing in NULL is particularly bad in the do_tftpb() case,
because eventually boot_get_kernel() will be called with a NULL cmdtp:

do_tftpb() -> netboot_common() -> bootm_maybe_autostart() -> do_bootm()
-> do_bootm_states() -> bootm_find_os() -> boot_get_kernel()

Around line 991 in cmd_bootm.c, boot_get_kernel() will dereference the
null pointer, and the board will crash.
Signed-off-by: NSteven A. Falco <stevenfalco@gmail.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: NTom Rini <trini@ti.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Add a MAC address create based on the OMAP die ID registers.
Then poplulate the ethaddr enviroment variable so that the device
tree alias can be updated prior to boot.
Signed-off-by: NDan Murphy <dmurphy@ti.com>

0x1D is reserved. So BUCK3DVS1 is started from 0x1e.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>

commit d196bd88 adds
redundand environment to mmc. The usage of malloc in
env_relocate_spec triggers cache errors on armv7.

Tested on a not mainlined i.MX53 board:

Board: TQMa53
I2C:   ready
DRAM:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57c2d8
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f57e2d8
ERROR: v7_dcache_inval_range - start address is not aligned - 0x8f57e2e0
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x8f5802e0
Using default environment
Signed-off-by: NMarkus Niebel <Markus.Niebel@tqs.de>

As the SPI controller is not initialized before env_init(), it causes
reading env in dataflash failed. So, although saveenv() successfully,
it shows warning information when reboot the system as following:

  *** Warning - bad CRC, using default environment

Let the env_relocate() to check env CRC and import it.
Signed-off-by: NBo Shen <voice.shen@atmel.com>

OMAP4 panda rev A6 is a 4430 es2.3 IC with an updated memory
part.

The panda rev A6 uses Elpida 2x4Gb memory and no longer uses Micron
so the timings needs to be updated
Signed-off-by: NDan Murphy <dmurphy@ti.com>

Signed-off-by: NTom Rini <trini@ti.com>

Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>

In [1] we discussed how we should deal with dual (or, more generally,
multiple) licensed files.  Add this to  Licenses/README  so it's
properly documented.

[1] http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/166518Signed-off-by: NWolfgang Denk <wd@denx.de>
[trini: Add the word 'list' to the end of the line, per Stephen Warren's
feedback]
Signed-off-by: NTom Rini <trini@ti.com>

When a toolchain invocation fails, an exception is thrown but not caught
which then aborts the entire toolchain detection process. To solve this,
request that exceptions not be thrown, since the toolchain init code
already error-checks the command result. This solves e.g.:

         - found '/usr/bin/winegcc'
Traceback (most recent call last):
...
Exception: Error running '/usr/bin/winegcc --version'

Change-Id: I579c72ab3b021e38b14132893c3375ea257c74f0
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NSimon Glass <sjg@chromium.org>
(formatted to 80cols)

The musb driver defines and uses MUSB_CSR0_H_DIS_PING, however this
bit is reserved on the DM36x. Thus this patch ensures that the
reserved bit is not accesssed.

It has been observed that some USB devices will fail to enumerate
with errors such as 'error in inquiry' without this patch.

See http://www.ti.com/litv/pdf/sprufh9a for details.

Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: NAndrew Murray <amurray@embedded-bits.co.uk>
Acked-by: NMarek Vasut <marex@denx.de>

OMAP5 boards may have both eMMC (on MMC2) and an SD slot (on MMC1).  We
Update the default bootcmd to match what happens on AM335x where we try
SD first, and then eMMC.  In this case however, the hardware layout used
for powering both of these means that in the kernel eMMC shall be found
first as it is powered by a fixed regulator and SD found second as SD is
powered via the palmas which will result in deferred probing.
Tested-by: NAparna Balasubramanian <aparnab@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

This allows you to write data to an UBI volume when the amount of memory
available to write that data from is less than the total size of the
data. For example, you may split a root filesystem UBIFS image into
parts, provide the total size of the image to the first write.part
command and then use multiple write.part commands to write the
subsequent parts of the volume. This results in a sequence of commands
akin to:

  ext4load mmc 0:1 0x80000000 rootfs.ubifs.0
  ubi write.part 0x80000000 root 0x08000000 0x18000000
  ext4load mmc 0:1 0x80000000 rootfs.ubifs.1
  ubi write.part 0x80000000 root 0x08000000
  ext4load mmc 0:1 0x80000000 rootfs.ubifs.2
  ubi write.part 0x80000000 root 0x08000000

This would write 384MiB of data to the UBI volume 'root' whilst only
requiring 128MiB of said data to be held in memory at a time.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NStefan Roese <sr@denx.de>

int64_t matches the bytes field in struct ubi_mkvol_req to which the
size is assigned. With the prior signed 32 bit integer, volumes were
restricted to being less than 2GiB in size.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NStefan Roese <sr@denx.de>