Skip to content

U
U-Boot.Mirror

OS / U-Boot.Mirror

通知 1
Star 0
Fork 0
U
U-Boot.Mirror

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 04 2月, 2020 1 次提交
  3. 23 1月, 2020 1 次提交
  5. 04 12月, 2019 1 次提交
  7. 21 11月, 2019 2 次提交
    • T
      env: Finish migration of common ENV options · a09fea1d
      由 Tom Rini 提交于 
      - In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
      a09fea1d
    • T
      env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol · 8d8ee47e
      由 Tom Rini 提交于 
      Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
      8d8ee47e
  9. 08 11月, 2019 1 次提交
  11. 14 8月, 2019 1 次提交
  13. 26 7月, 2019 1 次提交
    • J
      Add support for the NXP LS1021A-TSN board · 87821220
      由 Jianchao Wang 提交于 
      The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.

It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.

Supported boot media: microSD card (via SPL), QSPI flash.

Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).

Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).

To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.

eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: NXiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: NMingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: NJianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: NChangming Huang <jerry.huang@nxp.com>
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>

[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:

- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
  get overwritten during copying of the u-boot.bin payload from MMC to
  DDR.
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
      87821220
  15. 30 4月, 2019 1 次提交
  17. 19 2月, 2019 1 次提交
  19. 04 9月, 2018 1 次提交
  21. 18 8月, 2018 2 次提交
  23. 17 8月, 2018 1 次提交
    • T
      configs: Migrate CONFIG_NR_DRAM_BANKS · 86cf1c82
      由 Tom Rini 提交于 
      We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.
Signed-off-by: NTom Rini <trini@konsulko.com>
      86cf1c82
  25. 28 4月, 2018 1 次提交
    • A
      Convert CONFIG_SPI to Kconfig · f1b1f770
      由 Adam Ford 提交于 
      This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
      f1b1f770
  27. 09 4月, 2018 2 次提交
  29. 11 2月, 2018 1 次提交
    • T
      configs: Migrate CONFIG_SYS_TEXT_BASE · 278b90ce
      由 Tom Rini 提交于 
      On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: NTom Rini <trini@konsulko.com>
      278b90ce
  31. 31 10月, 2017 1 次提交
  33. 11 10月, 2017 1 次提交
    • T
      cmd: Toggle the default value of CONFIG_CMD_IMLS · ad12dc18
      由 Tuomas Tynkkynen 提交于 
      Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
      ad12dc18
  35. 28 8月, 2017 1 次提交
  37. 15 8月, 2017 1 次提交
  39. 10 8月, 2017 1 次提交
  41. 09 8月, 2017 1 次提交
  43. 08 8月, 2017 1 次提交
  45. 26 7月, 2017 1 次提交
  47. 01 5月, 2017 1 次提交
  49. 30 4月, 2017 1 次提交
  51. 14 4月, 2017 1 次提交
  53. 10 3月, 2017 1 次提交
    • T
      Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigs · 28522678
      由 Tom Rini 提交于 
      In some cases this is absolutely required, so select this for some secure
features.  This also requires migration of RSA_FREESCALE_EXP

Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Saksham Jain <saksham.jain@nxp.freescale.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
      28522678
  55. 28 1月, 2017 2 次提交
  57. 24 1月, 2017 1 次提交
  59. 22 1月, 2017 1 次提交
  61. 19 1月, 2017 1 次提交
  63. 05 1月, 2017 1 次提交
  65. 28 10月, 2016 1 次提交
  67. 24 10月, 2016 3 次提交