This commit moves:
- CONFIG_SPI_FLASH_BAR

from include/configs/*.h into configs/*_defconfigs
Signed-off-by: NJagan Teki <jteki@openedev.com>

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: NTom Rini <trini@konsulko.com>

Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: NTom Rini <trini@konsulko.com>

add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon).  Prior silicon is OK using this address as well.
Signed-off-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Reported-by: NShivasharan Nagalikar <shivasharan.nagalikar@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Enable booting from NAND on the am437xx-evm.
Signed-off-by: NTom Rini <trini@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"

The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

CONFIG_NET_MULTI is not used anywhere and thus can safely be removed
from the configs.
Acked-by: NMarek Vasut <marex@denx.de>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a83 (commands: add more
command entries in Kconfig).
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>

Across several devices network environment variables are duplicated.
Move these variables to a common include file which insures the environment
variables are reused and insures devices across product lines share the same
values.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: NLukasz Majewski <l.majewski@samsung.com>

AM43xx Industrial Development Kit is a new board
based on AM437x line of SoCs. Targetted at Industrial
Automation applications, it comes with EtherCAT, motor
control and other goodies.

Thanks to James Doublesin for all the help.

Cc: James Doublesin <doublesin@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Enable UUID and partition support for scripted handling platforms with
MMC and eMMC and varied partitioning schemes

And remove it from headers that end up redefining it.
Signed-off-by: NNishanth Menon <nm@ti.com>

By using CONFIG_ENV_IS_IN_FAT it's far easier
to have a private, minimal environment for e.g.
booting off of network or mounting rootfs on NFS
without having to modify the configuration header.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.

am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
  time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
  controlled by:
  (a) Statically using Jumper on connecter (J89) present on board.
  (a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
      by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
      SPI2_CS0 == 0: NAND (default)
      SPI2_CS0 == 1: eMMC

am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
  Thus only one of the two can be used at a time. Selection is controlled by:
  (a) Dynamically driving following GPIO pin from software
      GPMC_A0(GPIO) == 0 NAND is selected (default)

NAND device (MT29F4G08AB) on these boards has:
 - data-width=8bits
 - blocksize=256KB
 - pagesize=4KB
 - oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.
Signed-off-by: NPekon Gupta <pekon@ti.com>

Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.

Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NTom Rini <trini@ti.com>

AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This family is supported by the TPS65218 PMIC.  Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).
Signed-off-by: NTom Rini <trini@ti.com>

loadbootenv expects devtype variable to be set. This is missing in
mmcboot command. With this the following error comes:
U-Boot# run mmcboot
mmc0 is current device
SD/MMC found on device 0
** Bad device usb 0 **
** Bad device usb 0 **
Fixing this by setting devtype as mmc.
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared.  When SPL booting, this is handled by setting gd
to point to SRAM in s_init.  However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.
Signed-off-by: NTom Rini <trini@ti.com>

The ePOS EVM and EVM SK have QSPI as an option to boot.  Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices.  As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.

Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

QSPI booting on this board does not use SPL, so drop SPI-SPL related
options.
Signed-off-by: NTom Rini <trini@ti.com>

In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree.  In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.
Signed-off-by: NTom Rini <trini@ti.com>

Signed-off-by: NTom Rini <trini@ti.com>

To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.

It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff.  We don't do this by default to allow for
the most likely success of people using custom addresses however.
Signed-off-by: NTom Rini <trini@ti.com>

Add Ethernet Boot support to SPL
Acked-by: NTom Rini <trini@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>

Signed-off-by: NTom Rini <trini@ti.com>

Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Reviewed-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>

Add the USB host boot support for the am43xx evm
Add the macros to boot from a usb drive in uBoot
Signed-off-by: NDan Murphy <dmurphy@ti.com>

Upon further inspection of relevant parts of the architecture, the
maximum SPL binary size is 220KiB.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

Add support for reading onboard EEPROM to enable
board detection.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Add Extra env settings.
This is derived from am335x Extra ENV settings.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

AM4372 uses PL310 L2 Cache. Enable the configs for the same.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Use ti_armv7_common.h config file to inclde the common
configs.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Remove platform CONFIG_SYS_HZ definition for configs a-z*.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

Add the support for the am437x xhci usb host.

The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: NDan Murphy <dmurphy@ti.com>

Add config file
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>