The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: NStefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>

"host->version" isn't a SoC specific value.
It doesn't need to get in each SoC drivers.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NMinkyu Kang <mk7.kang@samsung.com>

These functions can be much simpler by squashing lines for immediate
return.

For *_bind() callbacks, they will be a simple wrapper function of an
upper-level bind API.

For mmc_set_{boot_bus_width,part_conf}, they will be a wrapper of
mmc_switch().
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>

We no longer need to set 'caps' as it's not passed to sdhci_setup_cfg
anymore.

Fixes: 14bed52d ("mmc: sdhci: remove the unnecessary arguments for
		sdhci_setup_cfg")
Signed-off-by: NTom Rini <trini@konsulko.com>

Some arguments don't need to pass to sdhci_setup_cfg.
Generic variable can be used in sdhci_setup_cfg, and some arguments are
already included in sdhci_host struct.

It's enough that just pass the board specific things to sdhci_setup_cfg().
After removing the unnecessary arguments, it's more simpler than before.
It doesn't consider "Version" and "Capabilities" anymore in each SoC
driver.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

buswidth isn't used anywhere in sdhci_setup_cfg.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NMinkyu Kang <mk7.kang@samsung.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Move zynq to the latest driver model support by enabling CONFIG_DM_MMC,
CONFIG_DM_MMC_OPS and CONFIG_BLK.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Update the existing drivers to set up this new pointer. This will be required
by the MMC uclass.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This allows to drop annoying (char *) casts when setting the host
name of struct sdhci_host.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Add quirk to disable high speed incase the high
speed was broken.This solves the issue where the
the controller is used in High Speed Mode and the
the hold time requirement for the JEDEC/MMC 4.41
specification is NOT met.
This timing issue is not on all boards and hence
provided config option to enable it when required.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NEmil Lenchak <emill@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Remove hardcoded value zero as min frequency and
use config option CONFIG_ZYNQ_SDHCI_MIN_FREQ
defined in board config
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Move driver to DM
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Prepare for using DM.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Calculate the minimum sd clock based on max clock. This will
be done by add_sdhci() if we pass minimum clock as zero.
It also does based on SD host contoller version.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

zc1571 with silicon can operate on 200MHz maximum frequency. Setup this
frequency by default and fix setting for ep108.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

We have flipped CONFIG_SPL_DISABLE_OF_CONTROL.  We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:

 #ifdef CONFIG_OF_CONTROL
 # if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
 #  define OF_CONTROL 0
 # else
 #  define OF_CONTROL 1
 # endif
 #else
 # define OF_CONTROL 0
 #endif

Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute.  It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.

Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.

[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NPantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>

Remove the quirk SDHCI_QUIRK_NO_CD as it is not
required.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

phys_addr_t is designed for physical addresses that's why
use it.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Enable initialize sdhci from DTB.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

As per the below commit
"mmc: sdhci: add the quirk for broken r1b response"
(sha1: 3a638320)
need to add quirk SDHCI_QUIRK_BROKEN_R1B, when the
response type is R1b.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: NTom Rini <trini@ti.com>

Add support for SD, MMC and eMMC card on Xilinx Zynq.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NTom Rini <trini@ti.com>