- 21 10月, 2013 26 次提交
-
-
由 Suriyan Ramasami 提交于
Add LED activity for SMSX95XX USB Ether driver. Signed-off-by: N“Suriyan Ramasami" <suriyan.r@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Mateusz Zalega 提交于
This commit unifies board-specific USB initialization implementations under one symbol (usb_board_init), declaration of which is available in usb.h. New API allows selective initialization of USB controllers whenever needed. Signed-off-by: NMateusz Zalega <m.zalega@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Reviewed-by: NLukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com>
-
由 Troy Kisky 提交于
Also, add other USB related config items. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
Select GPIO1 as the USB OTG ID pin for Nitrogen6x Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
desc is set at ep_enable, so for symmetry, clear it at ep_disable. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
Since we flush the TD, we may as well set it to a known value. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
Make sure the transfer descriptor is flushed before the queue is updated so that the controller will not see old information. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
This controller support full and high speed. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
Change 'nfo=' to 'info=' Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
This prevents a crash if tftpboot is given a bad filename. rx_req will be released by eth_reset_config which is called by eth_disconnect, which is called using the .disconnect member of usb_gadget_driver by mv_pullup in mv_udc which is called using the .pullup member of usb_gadget_ops by usb_gadget_disconnect which is called by usb_eth_halt which is called using the .halt member of eth_device by eth_halt which is called by TftpHandler when TFTP_ERR_FILE_NOT_FOUND or TFTP_ERR_ACCESS_DENIED occurs I trigger this with the following commands setenv ipaddr 10.0.0.2 && setenv netmask 255.255.255.0 && setenv serverip 10.0.0.1 setenv usbnet_devaddr 00:11:22:33:44:55 && setenv usbnet_hostaddr 00:aa:bb:cc:dd:ee setenv ethprime usb_ether && setenv ethact usb_ether && setenv ncip 10.0.0.1 tftpboot 10800000 10.0.0.1:missing_file Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Troy Kisky 提交于
set wMaxPacketSize for full speed descriptors fs_source_desc, fs_sink_desc to 64. Full-speed bulk endpoint can have a maximum packet size of 8, 16, 32, or 64 bytes, so choice 64. The hs_source_desc, hs_sink_desc, already have their wMaxPacketSize set to 512. That is the only legal value for high speed bulk endpoints. Strictly speaking, this patch is not needed because usb_ep_autoconfig will call ep_matches which will override wMaxPacketSize for BULK endpoints only with the size associated with the endpoint setup by the udc driver. But if you want to rely on this, you may as well combine the full speed descriptor with the high speed descriptor to minimize confusion. Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
-
由 Dan Murphy 提交于
Add the call back into the board file for to enable the SMPS10 VBUS regulator. Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Dan Murphy 提交于
Add the OMAP file for the xHCI Host controller This code will initilialize the proper components within the OMAP5 to enable the xHCI host controller. Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Dan Murphy 提交于
Add the prcm registers and the bit definitions to enable the USB SS port of the OMAP5 device. Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Dan Murphy 提交于
Add new functionality to turn on SMPS10 regulator. This supplies the VBUS to devices connected to the USB host ports Signed-off-by: NDan Murphy <dmurphy@ti.com>
-
由 Julius Werner 提交于
This patch adds a new samsung,vbus-gpio parameter to the device tree, in preparation of replacing the currently hardcoded VBUS GPIO mechanism in exynos5-dt.c with a device tree controlled solution, just as it already exists in the Linux kernel. Signed-off-by: NJulius Werner <jwerner@chromium.org> Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Marek Vasut <marex@denx.de>
-
由 Julius Werner 提交于
Some Exynos boards, such as the SMDK5250, control USB port power through a GPIO pin. For now this had been hardcoded in the exynos5-dt board file, but not all boards use the same pin, requiring local changes to support different boards. This patch moves the GPIO initialization into the USB host controller drivers which they belong to, and uses the samsung,vbus-gpio parameter in the device tree to configure it. Signed-off-by: NJulius Werner <jwerner@chromium.org> Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Marek Vasut <marex@denx.de>
-
由 Vivek Gautam 提交于
This enables support for xHCI host controller on Exynos5 and further disables EHCI support, to make sure only one host controller is enabled at a time, since right now using two controllers at a time is not possible with current usb core infrastructure. Anyone who wants to enable EHCI support again needs to enable CONFIG_USB_EHCI, CONFIG_USB_EHCI_EXYNOS once again in exynos5-dt config. Signed-off-by: NVikas C Sajjan <vikas.sajjan@samsung.com> Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
-
由 Vivek Gautam 提交于
XHCI stack driver needs this to align buffers to CacheLine boundary. So define the same to be '64' Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
-
由 Vivek Gautam 提交于
Adding device node for xhci host controller to enable usb 3.0 on exynos5250. Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
-
由 Vivek Gautam 提交于
Adding required compatible string for xHCI host controller as well as USB 3.0 PHY to enable dt support for usb 3.0 on exynos5. Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
-
由 Vivek Gautam 提交于
Adding methods to turn on/off power to USB3.0 type PHY as and when required by the controller. Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
-
由 Vivek Gautam 提交于
This adds driver layer for xHCI controller in Samsung's exynos5 soc. This interacts with xHCI host controller stack. Signed-off-by: NVikas C Sajjan <vikas.sajjan@samsung.com> Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
-
由 Vivek Gautam 提交于
This adds stack layer for eXtensible Host Controller Interface which facilitates use of USB 3.0 in host mode. Adapting xHCI host controller driver in linux-kernel by Sarah Sharp to needs in u-boot. Initial porting from Linux kernel version 3.4, with following top commit history of drivers/usb/host/xhci* : cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found This adds the basic xHCI host controller driver with bare minimum features: - Control/Bulk transfer support has been added with required infrastructure for necessary xHC data structures. - Stream protocol hasn't been supported yet. - No support for quirky devices has been added. Signed-off-by: NVikas C Sajjan <vikas.sajjan@samsung.com> Signed-off-by: NJulius Werner <jwerner@chromium.org> Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
-
由 Vivek Gautam 提交于
Macros defining bmRequestType field of USB device request, given in table 9.2 USB 2.0 spec, are rather generic macros which can be further used by other Host controller stacks. So moving them to usb_defs header. Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com> Cc: Julius Werner <jwerner@chromium.org> Cc: Simon Glass <sjg@chromium.org> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Vasut <marex@denx.de>
-
- 17 10月, 2013 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
- 16 10月, 2013 9 次提交
-
-
由 Michal Simek 提交于
The patch: "blackfin: Move blackfin watchdog driver out of the blackfin arch folder." (sha1: e9a389a1) changed hw_watchdog_init() prototype which didn't match with Microblaze one. This patch fixes the driver and Microblaze initialization. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
This bug was introduced by: "Add GPL-2.0+ SPDX-License-Identifier to source files" (sha1: 1a459660) Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Scott Wood 提交于
commit 39ac3447 ("cmd_mtdparts: use 64 bits for flash size, partition size & offset") introduced warnings in a couple places due to printf formats or pointer casting. This patch fixes the warnings pointed out here: http://lists.denx.de/pipermail/u-boot/2013-October/164981.htmlSigned-off-by: NScott Wood <scottwood@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Stefan Roese <sr@denx.de> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Tom Rini <trini@ti.com>
-
由 Timo Herbrecher 提交于
If dout buffer is not 32 bit-aligned or data to transmit is not multiple of 32 bit the read data pointer is already incremented on single byte reads. Signed-off-by: NTimo Herbrecher <t.herbrecher@gateware.de> Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
-
由 Bo Shen 提交于
As the spi flash transfer to multiple parts, it is forgot to add Atmel AT25DF321 spi flash support, which broken several Atmel EK boards which this chip. So, add it Signed-off-by: NBo Shen <voice.shen@atmel.com> Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
-
Added GPL-2.0+ SPDX-License-Identifier for missed spi source files. Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
-
Added GPL-2.0+ SPDX-License-Identifier for missed sf source files. Signed-off-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: NBo Shen <voice.shen@atmel.com>
-
- Add comments. - Renamed few macros. - Add tabs. Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: NBo Shen <voice.shen@atmel.com>
-
Unified the bank_sel calculation code for erase and write ops. Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
-
- 15 10月, 2013 4 次提交
-
-
python used in buildman doesn't need to be placed in /usr/bin/python, So use env to ensure that the interpreter will pick the python from environment. Usefull with several versions of python's installed on system. Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
由 Steven Falco 提交于
Pass a valid cmdtp into do_tftpb(), do_ext2load(), and do_get_fat(), to avoid possible crashes due to null pointer dereferencing. Commit d7884e04 does not go far enough. There is still at least one call chain that can result in a crash. The do_tftpb(), do_ext2load(), and do_get_fat() functions expect a valid cmdtp. Passing in NULL is particularly bad in the do_tftpb() case, because eventually boot_get_kernel() will be called with a NULL cmdtp: do_tftpb() -> netboot_common() -> bootm_maybe_autostart() -> do_bootm() -> do_bootm_states() -> bootm_find_os() -> boot_get_kernel() Around line 991 in cmd_bootm.c, boot_get_kernel() will dereference the null pointer, and the board will crash. Signed-off-by: NSteven A. Falco <stevenfalco@gmail.com>
-