- 11 8月, 2010 10 次提交
-
-
由 Mike Frysinger 提交于
Recent features enabled by default require a larger monitor size for the cm-bf548 port, so bump it up a bit. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Michael Hennerich 提交于
In case there is no frame buffer driver present in Linux to hand over the PPI LCD DMA upon boot, the DMA initiated by u-boot to display the splash screen runs unattended. Therefore always stop the video driver in u-boot before starting Linux. If people don't want this behavior, then they can simply stub out the video_stop() function in their board video driver. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Sergei Trofimovich 提交于
Before: Marvell>> usb storage Device 0: Vendor: StoreJet Rev: Prod: Transcend Type: Hard Disk Capacity: 28759.9 MB = 28.0 GB (488397168 x 512) After: Marvell>> usb storage Device 0: Vendor: StoreJet Rev: Prod: Transcend Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Signed-off-by: NSergei Trofimovich <slyfox@gentoo.org>
-
-
-
-
由 Albert Aribaud 提交于
Turn all ORION5X_DEF{ADR,SZ}_xxx macros into ORION5X_{ADR,SZ}_xxx and allow defining them from board code to override defaults. This is particularly useful for defining board-specific FLASH address and size in board header file rather than having to tweak orion5x code. Signed-off-by: NAlbert Aribaud <albert.aribaud@free.fr>
-
-
-
由 Wolfgang Denk 提交于
-
- 10 8月, 2010 9 次提交
-
-
由 Li Haibo 提交于
get_timer_masked() should return current timestamp, not current ticks from hardware register. Tested on one custom board with NAND flash. Without this patch, NAND write always TIMEOUT because get_timer(0) return a big value. This patch applies for u-boot-2010.06 Signed-off-by: NLi Haibo <hbli@sinocastel.com>
-
由 Reinhard Meyer 提交于
Remove warning for missing " at the end of line 136 Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>
-
由 Ben Warren 提交于
Commit 6e37b1a3a25004d3df5867de49fff6b3fc9c4f04 modifies several net calls to take a (const char *) parameter instead of (char *), but in some cases the modified functions call other functions taking (char *). The end result is warnings about discarding the const qualifier. This patch fixes these other function signatures. Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Mike Frysinger 提交于
For code that uses miiphy_{read,write}, every call invokes a full look up of the mii list. There is already a "current_mii" cache that is used by some code, but have the miiphy_{read,write} function use it as well. This does increase the code size slightly, but I think it's worth it. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Mike Frysinger 提交于
Rather than have every func re-implement the list walking code, do it one local function. This shrinks the resulting object code a little while making the source much more manageable. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Mike Frysinger 提交于
The driver name does not need to be writable, so constify it. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Kim Phillips 提交于
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8 "net ppc: fix ethernet device names with spaces" (currently in u-boot-net.git) for QE based parts. Signed-off-by: NKim Phillips <kim.phillips@freescale.com> Acked-by: NDave Liu <daveliu@freescale.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Heiko Schocher 提交于
since commit 1384f3bb ethernet names with spaces drop a Warning: eth device name has a space! message. This patch fix it for: - "FEC ETHERNET" devices found on mpc512x, mpc5xxx, mpc8xx and mpc8220 boards. renamed to "FEC". - "SCC ETHERNET" devices found on mpc8xx, mpc82xx based boards. Renamed to "SCC". - "HDLC ETHERNET" devices found on mpc8xx boards Renamed to "HDLC" - "FCC ETHERNET" devices found on mpc8260 and mpc85xx based boards. Renamed to "FCC" Tested on the kup4k board. Signed-off-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Stefano Babic 提交于
After discussion on the ML it is suggested to drop unrequired and not useful characters from the device name. This patch changes the name for the fec_mxc driver from "FEC_MXC" to "FEC". Signed-off-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 09 8月, 2010 21 次提交
-
-
由 Stefan Roese 提交于
This patch has the following fixes/changes: - Set 'kernel_addr' and 'ramdisk_addr' to correct values and add 'fdt_addr' environment variable - Remove 'kozio' environment variable - Remove environmant variables to boot ancient arch/ppc Linux kernels - Remove CONFIG_SYS_BOOTMAPSZ definition. It's already defined to the same value in amcc-common.h Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Heiko Schocher 提交于
Update image size after addition of new environment handling. Signed-off-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Update image size and default environment after addition of new environment handling. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Update image size after addition of new environment handling. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
Update image size after addition of new environment handling. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Wolfgang Denk 提交于
None of the AMCC boards uses an embedded environment, so there is no need to run "saveenv" after updating U-Boot. Drop the redundant commands from the default environment. Signed-off-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Mike Frysinger 提交于
Simply trying to include a basic header file like stdlib.h on OS X 10.5 and then building with -traditional-cpp fails with lots of errors like: In file included from /usr/include/stdlib.h:63, from test.c:3: /usr/include/available.h:85: error: stray '#' in program /usr/include/available.h:85: error: syntax error before numeric constant /usr/include/available.h:86: error: stray '#' in program In the past, I hadn't noticed because the old logic for these flags were restricted to Darwin running on PowerPC systems while I'm running on an Intel system. But after some recent clean ups and changes, the flag was being applied to all Darwin systems and my host tools broke. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Feng Wang 提交于
Original bug description from Feng (fdt_resize() bug caused "WARNING: could not set linux, initrd-start FDT_ERR_NOSPACE."): What I got is an error: "WARNING: could not set linux,initrd-start FDT_ERR_NOSPACE." after loading Device Tree blob. This in turn caused linux to miss init part. After some digging, I found out the reason for this error, it is caused by fdt_resize(). FDT blob got resized after filling in all board specific information of PowerPC. (in boot_body_linux()). It reduced blob size with only extra space for two fdt_reserve_entry, one for fdt itself, and one for initrd. Then it's aligned to a 0x1000 page boundary. However, later in fdt_initrd(), it could add two more properties, initrd-start AND initrd-end, each one needs at least two fdt_reserve_entry sizes done by _fdt_add_property() (name and value). Thus, the two fdt_reserve_entry extra space is not sufficient. So for some specific fdt size which is just under the page boundary after resizing, this will cause an error of FDT_ERR_NOSPACE in fdt_initrd() when setting those two properties, and failed to pass initrd information to linux. My fix is in fdt_resize(), leave at least 4 fdt_reserve_entry for initrd. So instead of 2*sizeof(struct fdt_reserve_entry) for actual_totalsize, use 5*sizeof(struc fdt_reserve_entry). Stefan: I got this same error on katmai, when trying to boot with initrd (run flash_self). This patch fixes this issue. Signed-off-by: NFeng Wang <fwang02@harris.com> Tested-by: NStefan Roese <sr@denx.de> Cc: Jerry Van Baren <gvb.uboot@gmail.com> Acked-by: NGerald Van Baren <vanbaren@cideas.com>
-
由 Frans Meulenbroeks 提交于
removed a variable that was not used Signed-off-by: NFrans Meulenbroeks <fransmeulenbroeks@gmail.com>
-
由 Frans Meulenbroeks 提交于
Most of the files have U_BOOT_CMD on a separate line, but a few didn't and had the first line on the same line as U_BOOT_CMD. This changes these files by adding a line break and a tab Signed-off-by: NFrans Meulenbroeks <fransmeulenbroeks@gmail.com>
-
由 Frans Meulenbroeks 提交于
removed the command name from the help message as it is already printed. for cmd_mmc also rewrote the message a little bit Signed-off-by: NFrans Meulenbroeks <fransmeulenbroeks@gmail.com>
-
由 Detlev Zundel 提交于
The invalidation of the old environment instance did not work for flashes supporting hardware locking. Now we unlock/lock around this update also. Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
由 Mike Frysinger 提交于
If a flash is unable to be detected, and then someone calls flash_protect on it (like the common code does in flash_init), the flash_protect logic will dereference a NULL pointer. Since flash_protect already does sanity checking on the info structs, add a NULL pointer check in there. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Wolfgang Denk 提交于
Fix error handling in getenv_f() when the user provided buffer is too short to hold the variable name; make sure to truncate and NUL-terminate without overwriting the buffer limits. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Mike Frysinger 提交于
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
Applying a little creative format string allows us to shrink the initial data read & display loop by only calling printf once. Re-using the local data buffer to generate the string we want to display then allows us to output everything with just one printf call instead of multiple calls to the putc function. The local stack buffer needs increasing by 1 byte, but the resulting code shrink and speed up is worth it I think. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
No need to output spaces 1 char at a time in a loop when the printf code can do the same thing with the right format string. This shrinks things and gives a nice speed up when killing off lines more than a byte or two as printf will send out the buffer in one big chunk. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-