This reverts commit 3649cd99.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This reverts commit 6f7576b2.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This reverts commit a85dd254.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This reverts commit f3a52fe0.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This reverts commit 5af61b2f.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This reverts commit 057004f4.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This reverts commit 8d17979d.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Changed the wording to properly describe the shadowing
of the environment from ROM to RAM
Signed-off-by: NBruce Adler <bruce.adler@acm.org>

Signed-off-by: NShinya Kuribayashi <skuribay@ruby.dti.ne.jp>

Signed-off-by: NVlad Lungu <vlad@comsys.ro>

The scan code of the key 'z' is 0x1d, which should be handled.

The change has be tested on NOVATEK USB keyboard and ULI PCI OHCI
controller.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>

The configuration file has already enabled USB, but it
missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB
on MPC8641HPCN can not work because of the wrong USB
register endian.

And add the USB command to U-Boot commands list.
Signed-off-by: NZhang Wei <wei.zhang@freescale.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

usb_cpu_init() configures GPS USB pins, clocks, etc. and
is required for proper operation of kernel USB subsystem.
This setup was previously done in the kernel by the fixup
code which is being removed, thus low level init must be
done by U-boot now.
Signed-off-by: NMarian Balakowicz <m8@semihalf.com>

An obvious typo. Originally fixed in linkstation u-boot port.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>

Since December 2003 the timer_interrupt_cpu() function in
cpu/mpc824x/interrupts.c contains what seems to be a superfluous
parameter. Remove it.
Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>

Add ft_cpu_setup(..)-function to adapt it for use with libfdt
based on code from mpc5xxx
Sigend-off-by: NSergej Stepanov <Sergej.Stepanov@ids.de>
--

To get the IDS8247 board working following are done:
 - FCC2 is deactivated
 - FCC1 is activated
 - I2C is activated
 - CFI driver is activated
 - Adapted for use with LIBFDT
Signed-off-by: NSergej Stepanov <Sergej.Stepanov@ids.de>
--

Wolfgang is right: It's not a good idea to set up default initial
ethernet addresses for a board, even though they belong to the local
range.

This will change the failure mode from "IT manager screams at you for
using duplicate ethernet addresses" to a nice error message explaining
that the ethernet address hasn't been set properly.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>

This is a multi-part message in MIME format.

commit e6e505eae94ed721e123e177489291fc4544b7b8
Author: Justin Flammia <jflammia@savantav.com>
Date:   Mon Oct 29 17:19:03 2007 -0400

    Found a bug in the way the DHCP Request packet is built, where the IP address
    that is offered by the server is bound to prematurely. This patch is a fix of
    that bug where the IP address offered by the DHCP server is not used until
    after the DHCP ACK from the server is received.
Signed-off-by: NJustin Flammia <jflammia@savantav.com>
Signed-off-by: NBen Warren <bwarren@qstreams.com>

Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>

With this patch PSC3 is configured as UART. This is done, because if
the pins of PSC3 are not configured at all (-> all pins are GPI),
due to crosstalk, spurious characters may be send over the RX232_2_TXD
signal line.
Signed-off-by: NMartin Krause <martin.krause@tqs.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Some commands for the STK52xx base board try to access the SM501 grafic
controller. But the TQM5200S has no grafic controller (only the TQM5200
and the TQM5200B have). This patch deactivates the commands accessing
the SM501 for the TQM5200S.
Signed-off-by: NMartin Krause <martin.krause@tqs.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

With this patch PSC3 is configured as UART. This is done, because if
the pins of PSC3 are not configured at all (-> all pins are GPI),
due to crosstalk, spurious characters may be send over the RX232_2_TXD
signal line.
Signed-off-by: NMartin Krause <martin.krause@tqs.de>