The driver is for all boards 24XX and up, so let's eliminate the
extra option called CONFIG_SYS_I2C_OMAP34XX since the driver checks
for CONFIG_OMAP34XX we don't need CONFIG_SYS_I2C_OMAP34XX.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>

This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: NTom Rini <trini@konsulko.com>

The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot.  select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.
Signed-off-by: NTom Rini <trini@konsulko.com>

This driver is used often enough such that we want to have this enabled
by default on any ARCH_OMAP2PLUS board, and this only compiles on
ARCH_OMAP2PLUS due to required defines, so mark that as the depends.
Signed-off-by: NTom Rini <trini@konsulko.com>

In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead.  With that
changed we can drop all defines of CONFIG_OMAP.  While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.
Signed-off-by: NTom Rini <trini@konsulko.com>

With the addition of Kconfig now having CONFIG_TWL4030_POWER and
with that being the default when OMAP34XX is selected, this
is no longer needed in include/configs and can be removed from the
whitelist.

This has only been tested on logic PD DM3730 using ti_omap3_common.h
Signed-off-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Move this in to Kconfig with a default of 115200.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: NTom Rini <trini@konsulko.com>

This moves all of the current ARM errata from various header files and in to
Kconfig.  This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config.  We now just select these once at the higher level in Kconfig
Signed-off-by: NTom Rini <trini@konsulko.com>

Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and
SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig.

Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to
Kconfig the board defconfigs for db-88f6820-gp_defconfig
kc1_defconfig and sniper_defconfig need to be updated.
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.

Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig.  Almost all
of the defines will go away.

I see only two exceptions:
  configs/blanche_defconfig
  configs/sandbox_noblk_defconfig

They define CONFIG_GENERIC_MMC, but not CONFIG_MMC.  Something
might be wrong with these two boards, so should be checked later.

Anyway, this is the output of the moveconfig tool.

This commit was created as follows:

[1] create a config entry in drivers/mmc/Kconfig

[2] tools/moveconfig.py -r HEAD GENERIC_MMC

[3] manual clean-up of garbage comments in doc/README.* and
    include/configs/*.h
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

We convert CONFIG_PARTITION_UUIDS to Kconfig first.  But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: NPatrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Move (and rename) the following CONFIG options to Kconfig:

  CONFIG_DAVINCI_MMC  (renamed to CONFIG_MMC_DAVINCI)
  CONFIG_OMAP_HSMMC   (renamed to CONFIG_MMC_OMAP_HS)
  CONFIG_MXC_MMC      (renamed to CONFIG_MMC_MXC)
  CONFIG_MXS_MMC      (renamed to CONFIG_MMC_MXS)
  CONFIG_TEGRA_MMC    (renamed to CONFIG_MMC_SDHCI_TEGRA)
  CONFIG_SUNXI_MMC    (renamed to CONFIG_MMC_SUNXI)

They are the same option names as used in Linux.

This commit was created as follows:

[1] Rename the options with the following command:

find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'

[2] Commit the changes

[3] Create entries in driver/mmc/Kconfig.
    (copied from Linux)

[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI

[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NMarek Vasut <marex@denx.de>

Commit 7a777f6d ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c79879 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.

We generally do not like such partial moves.  This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.

I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.

This commit was created as follows:

[1] Edit Kconfig (remove the "depends on", add the "default",
    copy the prompt and help message from Linux)

[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>

With the move to arch/arm/mach-omap2 there are now very few uses of
CONFIG_OMAP_COMMON and further they can all be replaced with
CONFIG_ARCH_OMAP2, so do so.
Signed-off-by: NTom Rini <trini@konsulko.com>

This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories.  All refernces to the former locations are updated to
the current locations.  For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_CONSOLE_IS_IN_ENV
   CONFIG_CONSOLE_MUX
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: Re-order, re-migrate]
Signed-off-by: NTom Rini <trini@konsulko.com>

Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures.  Migrate all config files.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Create a Kconfig entry for DISPLAY_CPUINFO and make it be the default
in certain architectures.  Migrate all config files.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move this option to Kconfig and tidy up existing uses.
Signed-off-by: NSimon Glass <sjg@chromium.org>

On all TI platforms the ROM defines a "downloaded image" area at or near
the start of SRAM which is followed by a reserved area.  As it is at
best bad form and at worst possibly harmful in corner cases to write in
this reserved area, we stop doing that by adding in the define
NON_SECURE_SRAM_IMG_END to say where the end of the downloaded image
area is and make SRAM_SCRATCH_SPACE_ADDR be one kilobyte before this.
At current we define the end of scratch space at 0x228 bytes past the
start of scratch space this this gives us a lot of room to grow.  As
these scratch uses are non-optional today, all targets are modified to
respect this boundary.

Tested on OMAP4 Pandaboard, OMAP3 Beagle xM

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Paul Kocialkowski <contact@paulk.fr>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Weber <weber@corscience.de>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: "B, Ravi" <ravibabu@ti.com>
Cc: "Matwey V. Kornilov" <matwey.kornilov@gmail.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: "Kipisz, Steven" <s-kipisz2@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Tested-by: NLokesh Vutla <lokeshvutla@ti.com>
Acked-by: NLokesh Vutla <lokeshvutla@ti.com>
Tested-by: NLadislav Michl <ladis@linux-mips.org>

This series moves the CONFIG_SYS_CACHELINE_SIZE.  First, in nearly all
cases we are mirroring the values used by the Linux Kernel here.  Also,
so long as (and in this case, it is true) we implement flushes in hunks
that are no larger than the smallest implementation (and given that we
mirror the Linux Kernel, again we are fine) it is OK to align higher.
The biggest changes here are that we always use 64 bytes for CPU_V7 even
if for example the underlying core is only 32 bytes (this mirrors
Linux).  Second, we say ARM64 uses 64 bytes not 128 (as found in the
Linux Kernel) as we do not need multi-platform support (to this degree)
and only the Cavium ThunderX 88xx series has a use for such large
alignment.

Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NLokesh Vutla <lokeshvutla@ti.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefan Agner <stefan.agner@toradex.com>
Acked-by: NHeiko Schocher <hs@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: NPaul Kocialkowski <contact@paulk.fr>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: N"Pali Rohár" <pali.rohar@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Alison Wang <b18965@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Saksham Jain <saksham.jain@nxp.com>
Cc: Qianyu Gong <qianyu.gong@nxp.com>
Cc: Wang Dongsheng <dongsheng.wang@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: tang yuantian <Yuantian.Tang@freescale.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hannes Schmelzer <oe5hpm@oevsv.at>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christophe Ricard <christophe-h.ricard@st.com>
Cc: Anand Moon <linux.amoon@gmail.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: huang lin <hl@rock-chips.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Xu Ziyuan <xzy.xu@rock-chips.com>
Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com>
Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ben Whitten <ben.whitten@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Carlos Hernandez <ceh@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ash Charles <ashcharles@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Daniel Allred <d-allred@ti.com>
Cc: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NChin Liang See <clsee@altera.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NPaul Kocialkowski <contact@paulk.fr>

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: NTom Rini <trini@konsulko.com>

A number of moveconfig.py runs have left a instances of multiple empty
lines in a row.  Correct this to a single empty line.
Signed-off-by: NTom Rini <trini@konsulko.com>

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND.  Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: NTom Rini <trini@konsulko.com>

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files.  Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.
Signed-off-by: NTom Rini <trini@konsulko.com>

And also reformat defconfigs using "make savedefconfig" rule.
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some
config headers. This is also probably fixes am335x_baltos board.
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
  - add next options to Kconfig selecting USB_GADGET_DUALSPEED:
    - USB_GADGET_ATMEL_USBA
    - USB_GADGET_DWC2_OTG
    - USB_DWC3
    - CI_UDC
  - make USB_MUSB_GADGET select USB_GADGET_DUALSPEED

While at it, make some related fixes:
  - remove DUALSPEED from configs that don't enable gadget support:
    - kwb.h
    - tseries.h
  - add missing USB_GADGET option to next configs:
    - novena_defconfig
    - pcm051_rev*_defconfig
    - xfi3_defconfig
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

The description was borrowed from kernel. Definitions were added to
defconfig files in a way that "make savedefconfig" generates exactly
the same file as used defconfig.

Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use
2 mA (as minimal allowed by Kconfig).
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

This makes the baudrate for the kernel command line explicit.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>