- 01 5月, 2017 13 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_DISPLAY Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_DIAG Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: imply CMD_DIAG on some keymile configs] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This option is not used in U-Boot. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_DEKBLOB Note: This option does not seem to actually be enabled by any board. Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: imply under SECURE_BOOT for mx5/6/7] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This option does not exist in U-Boot. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Rather than using CMD_CRAMFS for both the filesystem and its command, we should have a separate option for each. This allows us to enable CRAMFS support without the command, if desired, which reduces U-Boot's size slightly. Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: imply FS_CRAMFS for keymile] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_CRAMFS Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: imply CMD_CRAMFS for keymile] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_CLK Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: imply CMD_CLK on ARCH_ZYNQ] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This option is not used in U-Boot. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_CHIP_CONFIG Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Rather than using CMD_CBFS for both the filesystem and its command, we should have a separate option for each. This allows us to enable CBFS support without the command, if desired, which reduces U-Boot's size slightly. Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: imply FS_CBFS on SYS_COREBOOT] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_CBFS Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: imply CMD_CBFS on SYS_COREBOOT] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_SYS_WHITE_ON_BLACK Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Make this default y on various SoCs] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 30 4月, 2017 14 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_BSP Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_BMP Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Add depends on LCD || DM_VIDEO || VIDEO] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_BMODE Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Make this default y and depend on mx5/6/7] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_BLOB Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Add imply CMD_BLOB under CHAIN_OF_TRUST] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_BEDBUG Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_BAT Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This looks like a typo. Fix it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_AES CONFIG_AES Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Add select AES to CMD_AES] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
This option is not used in U-Boot. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This is only used by one board and should not be a CONFIG option. Instead it should use the driver model pmic framework. For now, just move the setting into the only board that uses it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_PMIC_AS3722 Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Most of the PMICs are in the drivers/power/pmic/ directory. Move this one there. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Before converting this to Kconfig, rename it to match the other PMICs. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Tom Rini 提交于
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 / CONFIG_MX53 being in Kconfig. Do so now. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 4月, 2017 13 次提交
-
-
git://www.denx.de/git/u-boot-microblaze由 Tom Rini 提交于
Xilinx fixes for v2017.05 - Fix usbotg on Miami board - Cleanup zc1751 defconfig
-
由 Lokesh Vutla 提交于
In file ext4fs.c funtion ext4fs_read_file() compares an unsigned expression with < 0 like below lbaint_t blknr; blknr = read_allocated_block(&(node->inode), i); if (blknr < 0) return -1; blknr is of type ulong/uint64_t. read_allocated_block() returns long int. So comparing blknr with < 0 will always be false. Instead declare blknr as long int. Similarly ext4/dev.c does a similar comparison. Drop the redundant comparison. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
Update Keystone2 secure device configs under "TI SYSTEM SECURITY". Without this buildman keeps complaining about the status of these boards. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Acked-by: NAndrew F. Davis <afd@ti.com>
-
由 Patrice Chotard 提交于
On ARM v7M, the processor will return to ARM mode when executing a blx instruction with bit 0 of the address == 0. Always set it to 1 to stay in thumb mode. Tested on STM32f746-disco board Similar commit: f99993c1 Author: Matt Porter <mporter@konsulko.com> Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Masahiro Yamada 提交于
In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs. Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this naming. Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim down the arch/arm/Kconfig level. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Josua Mayer 提交于
CONFIG_CMD_FS_UUID was neither whitelisted, nor was it declared in Kconfig. Now it can be enabled in .config and defconfig as expected. Signed-off-by: NJosua Mayer <josua.mayer97@gmail.com>
-
由 Andrew F. Davis 提交于
Almost all TI defconfigs enable this already, add this as a default and remove the explicit assignment. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Alexey Brodkin 提交于
Finally adding support for ARC boards in TravisCI. To build for ARC boards we need to install Synopsys prebuilt toolchain which we do here. Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lokesh Vutla 提交于
As per the DM[1] Dated June 2016–Revised February 2017, Table 5-3, DRA71 supports the following OPPs for various voltage domains: VDD_MPU: OPP_NOM VDD_CORE: OPP_NOM VDD_GPU: OPP_NOM VDD_DSPEVE: OPP_NOM, OPP_HIGH VDD_IVA: OPP_NOM, OPP_HIGH This patch add support for selection of the above OPPs instead of using OPP_NOM for all voltage domains. [1] http://www.ti.com/lit/ds/symlink/dra718.pdfReported-by: NVishal Mahaveer <vishalm@ti.com> Signed-off-by: NSuman Anna <s-anna@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Philipp Tomsich 提交于
This originally started out as "pinctrl: Kconfig: reorder to keep Rockchip options together" and tried to keep the Rockchip-related config options together. However, we now rewrite all chip-specific driver selections to start with CONFIG_PINCTRL_ (with the inadvertent changes to related Makefiles) and sort those alphabetically. And as this already means touching most of the file, we also reformat the help text to not exceed 80 characters (but make full use of those 80 characters). Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Philipp Tomsich 提交于
An assignment (of a value to itself) was left over (after removing and addition from the line) from moving the common padding code into rkcommon_vrec_header. This change removes this to avoid a spurious warning in static code analysis (i.e. Coverity). Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reported-by: Coverity (CID: 161418) Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Alexey Brodkin 提交于
These were reminders that somehow slipped through the cracks or were erroneously introduced after previous clean-ups. Getting rid of then once again. Hopefully for good now :) Where missing and appropriate replace with CONFIG_CMDLINE_EDITING which really enables shell history as of now. Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Peter Griffin <peter.griffin@linaro.org> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Steve Rae <steve.rae@raedomain.com> Cc: Jon Mason <jon.mason@broadcom.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Tom Rini 提交于
There are more and more cases where if we do not use gcc-6.0 or later we run into problems where our binaries are too large for the targets. Given the prevalence of gcc-6.0 or later toolchains at this point in time, we give notice now that starting with v2018.01 we will require gcc-6 (or later) for ARM. Signed-off-by: NTom Rini <trini@konsulko.com>
-