Signed-off-by: NWolfgang Denk <wd@denx.de>

Conflicts:

	cpu/ppc4xx/fdt.c
	include/configs/kilauea.h
	include/configs/sequoia.h
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch adds some BSP commands and FPGA booting support
for esd's PMC440 boards.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch adds the first files for the new esd PMC440 boards.
The next two patches will complete the PMC440 board support.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

- add EEPROM write protection for esd PLU405 boards.
- initialize NAND GPIOs
- use correct io accessors
- cleanup
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

This patch fixes esd's LCD dectection code to work correctly with
newer gcc versions.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

- add EEPROM write protection
- initialize NAND GPIOs
- use correct io accessors
- slow down I2C clock to 100kHz
- enable ext. I2C bus
- cleanup
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

In an attmemt to clean up the 4xx start.S file, I removed the enabling
of the internal 405EP PCI arbiter. This is needed for multiple other
405EP platforms, like most of the esd 405EP. Now the internal PCI
arbiter is enabled again per default as it has been before.
Signed-off-by: NStefan Roese <sr@denx.de>
Acked-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Signed-off-by: NStefan Roese <sr@denx.de>
Acked-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Use correct link to nand_ecc now located in drivers/mtd/nand/ for the
platforms mentioned above.
Signed-off-by: NStefan Roese <sr@denx.de>

This board never left prototyping state and it
became a millstone round my neck. So remove it.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

These patches add support for the PPC440EPx-based "Korat" board to
U-Boot.  They are based primarily on support for the Sequoia board.
Signed-off-by: NLarry Johnson <lrj@acm.org>

This patch supplies the configuration file for the Korat PPC440EPx-
processor board.
Signed-off-by: NLarry Johnson <lrj@acm.org>

Signed-off-by: NLarry Johnson <lrj@acm.org>

This patch adds SPD DDR2 support for the 440EPx ("Denali") SDRAM
controller.  It should also work on the 440GRx.  It is based on the DDR2
SPD code for the 440EP/440EPx, but makes no provision for DDR1 support.

This code has been tested on prototype Korat boards with three Kingston
DIMMS: 512 MiB ECC (one rank), 512 MiB non-ECC (one rank) and 1 GiB ECC
(two ranks).  The Korat board has a single DIMM socket, but support has
been provided (though not tested) for boards with two DIMM sockets.
Signed-off-by: NLarry Johnson <lrj@acm.org>

This patch creates a non-board-specific file for performing the SDRAM
data-eye search.  It also adds ECC error checking to the test of valid
data on readback when ECC is enabled.
Signed-off-by: NLarry Johnson <lrj@acm.org>

This patch adds the Denali SDRAM controller definitions to "ppc440.h".
It also fixes two typos in the definitions, so the board-specific
"sdram.h" files containing these definitions are also fixed to avoid
compiler warnings.
Signed-off-by: NLarry Johnson <lrj@acm.org>

This patch adds a new switch: "CONFIG_PHY_DYNAMIC_ANEG".  When this symbol
is defined, the PHY will advertise it's capabilities for autonegotiation
based on the capabilities shown in the PHY's status registers, including
1000BASE-X.  When "CONFIG_PHY_DYNAMIC_ANEG" is not defined, the PHY will
advertise hard-coded capabilities, as before.
Signed-off-by: NLarry Johnson <lrj@acm.org>

This driver is based on the driver for the LM75.
Signed-off-by: NLarry Johnson <lrj@acm.org>

This driver is based on the driver for the M41T11.  In the intended
application, the RTC will be powered by a large capacitor, rather than a
battery.  The driver therefore checks to see whether the RTC has lost
power.  The chip's OUT bit is normally reset from its power-up state.  If
the OUT bit is read as set, or if the date and time are not valid, then the
RTC is assumed to have lost power, and its date and time are reset to
1900-01-01 00:00:00.

Support for adjusting the speed of the clock to improve accuracy is
provided through an environment variable.
Signed-off-by: NLarry Johnson <lrj@acm.org>

Signed-off-by: NLarry Johnson <lrj@acm.org>

Signed-off-by: NLarry Johnson <lrj@acm.org>

Signed-off-by: NLarry Johnson <lrj@acm.org>

Signed-off-by: NStefan Roese <sr@denx.de>

On Sequoia & LWMON5 the virtual address of the POST cache test is now
moved to a bigger address. This enables usage of more memory on those
boards.
Signed-off-by: NStefan Roese <sr@denx.de>

As repoted by Larry Johnson, running "diag run cache" caused a crash
in U-Boot. This problem was introduced by a patch that removed the
TLB entry for the cache test after the test has completed. Since this
TLB was only setup once, a 2nd attempt to run this cache test
failed with a crash. Now this TLB entry is created every time the
routine is called.
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

Now the cpu node setup ("timebase-frequency" and "clock-frequency") is
without using the absolute path to the cpu node. This makes it possible
to use this U-Boot version with both versions of cpu-node naming
"cpu@0" and the former "PowerPC,440EPx@0".
Signed-off-by: NStefan Roese <sr@denx.de>

Now that the 440EPx ECC test is not board specific anymore
remove this Makefile.
Signed-off-by: NStefan Roese <sr@denx.de>

ppc4xx clear_bss() fails if BSS segment size is not
divisible by 4 without remainder. This patch provides
fix for this problem.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Signed-off-by: NNiklaus Giger <niklaus.giger@netstal.com>

When using dhcp/bootp the "netmask" environment variable is not
set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is
desireable, so the following patch adds this this option to the board
config.
Signed-off-by: NMarkus Klotzbuecher <mk@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch allows the ECC POST to be used for different boards with the
PPC440 Denali SDRAM controller.  Modifications include skipping the test
if ECC is not enabled (as for non-ECC DIMMs) and adding synchronization
to prevent timing errors.
Signed-off-by: NLarry Johnson <lrj@acm.org>

Signed-off-by: NLarry Johnson <lrj@acm.org>