The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This board is similar to keymile suen3.
Signed-off-by: NClive Stubbings <clive.stubbings@xentech.co.uk>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount

This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>

- fix board support following relocation changes
- switch to boards.cfg
- disable i2c to keep size under 128kiB (1 sector)
Signed-off-by: NEric Bénard <eric@eukrea.com>

- update to new relocation code
- switch to boards.cfg
- get rid of LEGACY (still a little hack in .h to compile)
- add nand boot configuration
- boot tested for the following configurations :
	9260 (64MB RAM & nor boot)
	9260_nand (64MB RAM & nand boot)
	9G20_128M (128MB RAM & nor boot)
	9G20_nand_128M (128MB RAM & nand boot)
	(nor boot is using lowlevel init)
Signed-off-by: NEric Bénard <eric@eukrea.com>

Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.

The board support is based on the BeagleBoard implementation.
Signed-off-by: NLuca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: NSrinath <srinath@mistralsolutions.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: NJason Liu <r64343@freescale.com>

The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: NStefano Babic <sbabic@denx.de>

Old address of RESET_VECTOR were overwritten by the bss sector, making
impossible its run from xmd.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NGraeme Russ <graeme.russ@gmail.com>

PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: NChunhe Lan <b25806@freescale.com>
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NShaohui Xie <b21989@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NChong Huang <chuang@ucrobotics.com>
Signed-off-by: NHaitao Zhang <minipanda@linuxrobot.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Info about the hardware can be found here:
	http://www.dilnetpc.com/dnp0086.htmSigned-off-by: NAndreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NZhao Chenhui <b35336@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NJiang Yutang <b14898@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for 36-bit address map for NOR, SD, and SPI boot cfgs.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Au1x00 is a SoC and its specific code should reside in an own
SoC subdirectory. Also add -mtune=4kc flag for CPU optimization.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Thomas Lange <thomas@corelatus.se>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

IncaIP is a SoC and its specific code should reside in an own
SoC subdirectory. Also add -mtune=4kc flag for CPU optimization.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

All current CPUs and SoCs are based on MIPS32 arch. The complete
code resides in the global arch/mips/cpu directory. This is not
suitable if other MIPS architectures like MIPS64 or Octeon should
be supported in the future.

To achieve this the current CPU code is moved to its own mips32
subdirectory. All MIPS32 boards have to use mips32 as config switch
in board.cfg.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with
* Processor upto 806Mhz
* LPDDR1/2
* x8/x16 SLC/MLC NAND
* Footprints for eMMC & MMC x8 card

With Peripherals:
* Parallel LCD I/F
* Audio codecs (88PM8607)
* MIPI CSI-2 camera
* Marvell 88W8787 802.11n/BT module
* Marvell 2G/3G RF
* Dual analog mics & speakers, headset jack, LED, ambient
* USB2.0 HS host, OTG (mini AB)
* GPIO, GPIO expander with DIP switches for easier selection
* UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality
Signed-off-by: NLei Wen <leiwen@marvell.com>
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Signed-off-by: NTom Warren <twarren@nvidia.com>

Signed-off-by: NTom Warren <twarren@nvidia.com>

Position independant functionality is due for removal from the x86
architecture, so create two distinct configurations - One for Flash and
one for SRAM

We should have been defining the actual board name in the options, not
the processor.  Fix this for P1011RDB, P1020RDB, P2010RDB, and P2020RDB.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>
Acked-by: NStefan Roese <sr@denx.de>

Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

At the same time, fix up CPU_CLOCK_RATE to have the CONFIG_ prefix to
work with boards.cfg.
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

CONFIG_QEMU_MIPS is already provided by <configs/qemu-mips.h>, so we
don't generate it using the options fields in boards.cfg.
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

CONFIG_GTH2 is already provided by <configs/gth2.h>, so we don't
generate it using the options fields in boards.cfg.
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.

This patch supports the following functions:
 - 256MB DDR3-SDRAM
 - SPI ROM
 - Ethernet
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

This patch adds support for Samsung s5pc210 universal board
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

This patch adds support for CM-T35 board
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).

The board boots from the NOR flash. Following devices
are supported:
 - two ethernet devices (FEC and SMC911x on debug board)
 - I2C
 - PMIC (MC13892) via I2C interface
 - UART
 - NOR flash (64MB)
 - NAND flash (2GB)
 - basic access to mc9sdz60 registers via I2C interface
Signed-off-by: NStefano Babic <sbabic@denx.de>