- 11 4月, 2008 1 次提交
-
-
由 Stefan Roese 提交于
This patch reworks the default environment on Kilauea/Haleakala. Now "net_nfs" for exmaple uses the device-tree style booting formerly know as "net_nfs_fdt". Also the addresses in RAM were changed because of the new image booting support, which check for image overwriting. So the addresses needed togeet adjusted. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 03 3月, 2008 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 17 1月, 2008 1 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 28 12月, 2007 2 次提交
-
-
由 Stefan Roese 提交于
Now the cpu node setup ("timebase-frequency" and "clock-frequency") is without using the absolute path to the cpu node. This makes it possible to use this U-Boot version with both versions of cpu-node naming "cpu@0" and the former "PowerPC,440EPx@0". Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch update the 4xx fdt support. It enabled fdt booting on the AMCC Kilauea and Sequoia for now. More can follow later quite easily. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 13 12月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
This patch update the 4xx fdt support. It enabled fdt booting on the AMCC Kilauea and Sequoia for now. More can follow later quite easily. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 08 12月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
This patch selects the USB data pins in the 405EX GPIO and MFC (multi function control) registers. This is done for the AMCC Kilauea and Makalu eval boards. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 27 11月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
After an error in the AMCC 405EX users manual now correctly configure IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ usage. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 26 11月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 17 11月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) Signed-off-by: NStefan Roese <sr@denx.de>
-
- 09 11月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 03 11月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
This patch adds NAND booting support for the AMCC 405EX(r) eval boards. Again, only one image supports both targets. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 01 11月, 2007 7 次提交
-
-
由 Stefan Roese 提交于
All 4xx board config files don't need the cache definitions anymore. These are now defined in common headers. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
The Haleakala is nearly identical with the Kilauea eval board. The only difference is that the 405EXr only supports one EMAC and one PCIe interface. This patch adds support for the Haleakala board by using the identical image for Kilauea and Haleakala. The distinction is done by comparing the PVR. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch adds support for dynamic configuration of PCIe ports for the AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe boards Yucca & Katmai and the 405EX board Kilauea. This dynamic configuration is done via the "pcie_mode" environement variable. This variable can be set to "EP" or "RP" for endpoint or rootpoint mode. Multiple values can be joined via the ":" delimiter. Here an example: pcie_mode=RP:EP:EP This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2 as endpoint. Per default Yucca will be configured as: pcie_mode=RP:EP:EP Per default Katmai will be configured as: pcie_mode=RP:RP:REP Per default Kilauea will be configured as: pcie_mode=RP:RP Signed-off-by: NTirumala R Marri <tmarri@amcc.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch enables the fdt support on the AMCC Kilauea eval board. Additionally now EBC ranges fdt fixup is included to support NOR FLASH mapping via the Linux physmap_of driver. This Kilauea port now support booting arch/ppc and arch/powerpc Linux kernels. The default environment "net_nfs" is for arch/ppc and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc support will be removed. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-