- 12 4月, 2016 1 次提交
-
-
由 Hans de Goede 提交于
We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after its Kconfig conversion it has ended up missing on some recently added boards. Simply select it for ARCH_SUNXI, so that we get it on all sunxi boards for both a consistent user experience and simpler defconfig files. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Acked-by: NIan Campbell <ijc@hellion.org.uk>
-
- 01 4月, 2016 1 次提交
-
-
由 Chen-Yu Tsai 提交于
The Cubietruck Plus uses all 3 USB controllers: - USB OTG functions are provided by the musb USB OTG controller - Onboard SATA is provied by a USB-SATA bridge connected to USB1 - The USB host ports on the board are provided by an HSIC USB hub FLDO1 is set to 1.2V for HSIC. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Reviewed-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
- 24 3月, 2016 1 次提交
-
-
由 Chen-Yu Tsai 提交于
Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers. The board also has an EEPROM on i2c0 which holds the MAC address. DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 is connected to the reset control of the PHY. EMAC is not actually supported yet. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Acked-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
- 15 3月, 2016 1 次提交
-
-
由 Simon Glass 提交于
There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: NSimon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 1月, 2016 1 次提交
-
-
由 Vishnu Patekar 提交于
Add dts and defconfig for Banana-pi M3 board. It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI, mic, AP6212 Wifi, etc on it. It is paired with AXP813 PMIC which is almost same as AXP818. Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com> [hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts] Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
- 10 12月, 2015 2 次提交
-
-
由 Hans de Goede 提交于
Select SYS_NS16550 from Kconfig instead of setting it in all our defconfig files. Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-
由 vishnupatekar 提交于
Add dts and defconfig for h8homletv2 board. H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner. It has UART, ethernet, USB, HDMI, etc ports on it. A83T patches are tested on this board. Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com> Reviewed-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NHans de Goede <hdegoede@redhat.com>
-