Synchronize R-Car Gen3 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Synchronize R-Car Gen2 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Linux 5.0, commit 1c163f4c7b3f621efff9b28a47abb36f7378d783,
has a TDSEL fix for R8A7790 H2 and R8A7794 E2 SoCs, implement
similar fix for U-Boot. The difference here is that the SoC
ES matching has to be implemented manually.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Synchronize R-Car Gen3 clock tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Synchronize R-Car Gen2 clock tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add defconfig and board specific adjustments for the R8A77965 M3N ULCB.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Import R8A77965 M3N ULCB device trees from Linux 5.0 ,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add pin control tables for R8A77965 from Linux 5.0 .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add clock tables for R8A77965 from Linux 5.0 , except for the
crit, R and Z clock, which are neither used nor supported by
the U-Boot clock framework yet.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add dedicated entry for R8A77965 M3N SoC.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Enable LZO compression of the multi-DTB fitImages, since the U-Boot
with multiple DTs enabled is becoming quite large and the DTs can
be well compressed. The LZO compression saves almost 200 kiB on the
Salvator-X(S) and ULCB targets.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add required Kconfig symbols, Makefile bits and macro fixes in a
few places to support LZO and DT compression in U-Boot. This can
save a lot of space with multi-DTB fitImages.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>

Allow enabling both LZO and GZIP DT compression in SPL and fix a
bug where if the GZIP decompression failed, the LZO decompression
would not even be attempted.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>

The ATF can pass additional information via the first four registers,
x0...x3. The R-Car Gen3 with mainline ATF, register x1 contains pointer
to a device tree with platform information. Save these registers for
future use.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Split fdtdec_setup_memory_banksize() into fdtdec_setup_memory_banksize_fdt(),
which allows the caller to pass custom blob into the function and the
original fdtdec_setup_memory_banksize(), which uses the gd->fdt_blob. This
is useful when configuring the DRAM properties from a FDT blob fragment
passed in by the firmware.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Split fdtdec_setup_mem_size_base() into fdtdec_setup_mem_size_base_fdt(),
which allows the caller to pass custom blob into the function and the
original fdtdec_setup_mem_size_base(), which uses the gd->fdt_blob. This
is useful when configuring the DRAM properties from a FDT blob fragment
passed in by the firmware.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

In case the gunzip() call fails, it will print an error message.
If that happens within the YModem session, the error message will
not be displayed and would be useless. Move the gunzip() call out
of the YModem session to make those possible error messages visible.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>

In case spl_parse_image_header() errors out, terminate the YModem
session, otherwise we won't get any further output.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>

Signed-off-by: NTom Rini <trini@konsulko.com>

Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.

Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]

So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.

Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.

[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.htmlReported-by: NPablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

- i.MX8QXP-MEK ethernet fix

PHY cannot be detected unless we wait about 150 ms.
Signed-off-by: NAndrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>
Reviewed-by: NStefano Babic <sbabic@denx.de>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
  a delay of phy-reset-post-delay milliseconds will be observed after the
  phy-reset-gpios has been toggled. Can be omitted thus no delay is
  observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: NAndrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>
Reviewed-by: NStefano Babic <sbabic@denx.de>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Acked-by: NLukasz Majewski <lukma@denx.de>

This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: NMichal Simek <michal.simek@xilinx.com>

Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Tested-by: NLukasz Majewski <lukma@denx.de>

Fixes for 2019.04

	- fix bashism for MX8
	- fix ethernet for MX53
	- fix docs for i.MX8

- Documentation fix

- Important Khadas VIM2 fix
- Build fix for macOS Mojave
- Build fix for gcc-4.7 for host tools.

Parts of the code are using C99 constructs (such as variables declared
inside loops), but also GNU extensions (such as typeof), so using
-std=gnu99 is necessary to build with older versions of gcc that don't
default to building with gnu99.

It fixes the following build failure:

./tools/../lib/crc16.c: In function "crc16_ccitt":
./tools/../lib/crc16.c:70:2: error: "for" loop initial declarations are only allowed in C99 mode
  for (int i = 0;  i < len;  i++)
  ^
./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code

when building the host tools with gcc 4.7.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

The Khadas VIM2 defconfig was missing the USB PHY config and
two other misc configs to setup dram banks and call misc_init_r.
Align it on the other Amlogic SoC based boards defconfig.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.

Fixes: 2960e27e ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

Fix missing at91 boards and split the at91 in two categories:
at91 arm v7
at91 arm926esj
which are the two main cores for the at91 architecture.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b791

The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Signed-off-by: NLukasz Majewski <lukma@denx.de>

After running tools/moveconfig.py it turned out that for various boards
there are an empty #ifdef statements.

Remove them to clean u-boot source code.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

The ohci driver calls board_usb_init(), not usb_board_init().
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>

Let the underline marker "=" fill the whole sentence for better
readability.
Signed-off-by: NFabio Estevam <festevam@gmail.com>

The DDR firmware binaries should be copied to '$(srctree)', so fix
a typo.
Signed-off-by: NFabio Estevam <festevam@gmail.com>

After building ATF it is needed to copy the generated bl31.bin file to
the U-Boot source tree.

Make this step explicit in the instructions.
Signed-off-by: NFabio Estevam <festevam@gmail.com>