Add hash and hash verify commands. These would be useful for
verifying copied data.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Enable NAND on mmc defconfig for greater flexibility and for consistency
reasons. All our other boards that have a NAND flash integrated, enable
NAND regardless of the type of the defconfig.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Not correcting anything in case of empty ECC data area
is not an appropriate strategy, because an uncorrected bit-flip
in an empty sector may cause upper layers (namely UBI) fail to work
properly. Therefore the approach chosen in Linux kernel and other
u-boot mtd drivers has been adopted, where a heuristic implemented
by nand_check_erased_ecc_chunk() is used in order to detect and
correct empty sectors.

Tested with sama5d3_xplained and sam9x60-ek.
Signed-off-by: NKai Stuhlemmer (ebee Engineering) <kai.stuhlemmer@ebee.de>
Tested-by: NTudor Ambarus <tudor.ambarus@microchip.com>
[ta: reorder if conditions, change commit subject, s/uint8_t/u8.]
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

This reverts commit 786f888b.

Looks like the datasheet at
https://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D3-Series-Data-sheet-DS60001609b.pdf
is wrong, and the testing was poorly done, because the PMECC did not raise
any error, but also didn't correct any bitflips. Restoring the offsets
as they were before, makes the PMECC on sama5d3x capable of correcting
bitflips.

Fixes: 786f888b ("sama5d3: Fix Galois Field Table offsets")
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Add default bootarguments with booting from mmc0 for this configuration.
This will allow a default Linux boot for this board.
Suggested-by: NJarvis Chen <jarvis.chen@microchip.com>
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Increase the BOOTM_LEN to 32M . This would allow a bigger kernel image to be
booted, for example the multi_v7_defconfig.

   Loading Kernel Image
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
resetting ...
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Fix comment typos
Signed-off-by: NIlko Iliev <iliev@ronetix.at>

Enable CONFIG_DM_ETH in configs/pm9263_defconfig
Drop legacy initialization in board/ronetix/pm9263.c
Remove network related setting from include/configs/pm9263.h
Signed-off-by: NIlko Iliev <iliev@ronetix.at>

The network support is removed because there is
no DM for Davicom DM9000.
Signed-off-by: NIlko Iliev <iliev@ronetix.at>

This commit updates the default config with the values that are actually
used "in the wild" and which are close to what is used on the MediaTek
MT7688 based, 2nd generation of the GARDENA smart gateway:
 - Reduce startup time by setting bootdelay to 0 (still allows accessing
   the shell, one just has to send a key press quicker)
 - Adjusting U-Boot environment volume names and MTD partitions to
   the actual layout
Signed-off-by: NReto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: NStefan Roese <sr@denx.de>

Signed-off-by: NTom Rini <trini@konsulko.com>

- RCar3 improvements

This fixes the broken H5 Ethernet and updates the R40 and A64 DT files,
so nothing really critical.

Import updated devicetree files from the Linux v5.12 release.

Besides some node and audio port renames this changes the PHY modes to
either rgmii-id or rgmii-txid. From the board files the Pinephone sees
a lot of updates.

This also adds the long missing USB PHY property for controller 0, which
allows the U-Boot PHY driver to eventually use port 0 in host mode
(pending another U-Boot patch).
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NJernej Skrabec <jernej.skrabec@siol.net>

Update R40 .dts{,i} and dt-binding headers to current version from kernel.

Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: NIvan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Commit eb5a2b67 ("net: sun8i-emac: Determine pinmux based on SoC,
not EMAC type") switched the pinmux setup over to look at
CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
Unfortunately this patch missed to check for the H5, which is
pin-compatible to the H3, but uses a different Kconfig symbol (because
it has ARMv8 vs. ARMv7 cores).

Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
there to cover the peripherals common to both SoCs.
Also explicitly list each supported SoC, and have an error message in the
fallback case, to avoid those problems in the future.

This fixes Ethernet support on all H5 boards.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi PC2
Reviewed-by: NRamon Fried <rfried.dev@gmail.com>

Enable support for PCIe NVMe devices.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>

Enable CONFIG_SYS_FLASH_PROTECTION on Salvator-X(S), ULCB, Ebisu,
which means the Spansion HF PPB protection bits can be operated
using the 'protect' U-Boot command.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Synchronize Gen2 MSTP teardown tables with datasheet Rev.2.00
Feb 01, 2016. This corrects the following bits:
  - added H2 MSTP3[10] SCIF2
  - added H2/M2/E2 MSTP7[29] TCON
  - removed E2 MSTP5[22] Thermal Sensor
  - removed E2 MSTP10[31,24:22] SRC0, SRC7:9
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The clock driver used a heavy-handed approach where it turned off
all available clocks, while also possibly setting bits which are not
documented in the R-Car datasheet. Update the tables so that only
the bits which are documented are set or cleared when tearing down
the clock driver.

Note that the only clock left running before booting Linux are now
MFIC, INTC-AP, INTC-EX and SCIF2 / SCIF0 on V3x.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>

- MIPS: octeon: fix minor bugs of initial merge
- MIPS: octeon: add support for QLM and PCI-E controller
- MIPS: octeon: add support for AHCI and SATA
- MIPS: octeon: add E1000 ethernet support
- MIPS: octeon: add Octeon III NIC23 board
- ata/scsi: add support for Big Endian platforms

Bump our py version to 1.10.0 to address CVE-2020-29651.

Reported-by: GitHub dependabot
Reported-by: NLey Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

 - search for additional detailed timings in the EDID extension block
 - rework sunxi DE2 driver and accompanying DW-HDMI platform driver
   to drop redundant device specific code, and later use the DT as a
   source of information

Pull request for efi-2021-07-rc1-3

Documentation fixes

UEFI bug fixes:

* error handling for capsule updates

Currently DE2 driver uses functions which are defined in internal
headers. They are not meant to be used outside of uclass framework.
Switch DE2 driver to public ones. This has additional benefit that
device_probe doesn't need to be called manually.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

There is no real need to read source_id at probe time. It also doesn't
make sense to store it in driver private data since it's already stored
in class platform data. While this looks like cleanup (and it is), it's
also important for DE2 driver rework because this info will be filled
later (after probe is already executed).
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

TV driver was never fully implemented. Remove search for it from DE2
driver.
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

No Allwinner board with DW-HDMI controller use separate I2C bus for
EDID read. Remove that check.
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

It turns out that there are two ways how hot plug detection can be done.
One is standard way for DW HDMI controller - checking bit 2 in 0x3004
register. Another way is applicable only to Allwinner custom PHY - by
checking bit 19 in register 0x10038. Both methods are equally good as
far as we know.

Use standard method in order to reduce amount of custom code.
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

One of my monitors have only 4k@60 timing in base EDID block which is
out of range for devices with HDMI 1.4. It turns out that it has
additional detailed timings in CTA-861 Extension Block and two of them
are appropriate for HDMI 1.4.

Add additional search for valid detailed timing in extension block.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Acked-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Code which searches for valid detailed timing entry will be used in more
places. Extract it.

No functional change is made. However, descriptors are casted to
edid_detailed_timing instead of edid_monitor_descriptor. Descriptor can
be of either type, but since we're interested only in DTD, it is more
fitting to cast to edid_detailed_timing.
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

When searching for detailed timing in EDID, check for digital display
earlier. There is no point parsing other parameters if this flag is not
present.
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Currently driver accepts all resolution which won't work on 4k screens.
Add validation callback which limits acceptable resolutions to 297 MHz.
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

commit cbea241e("efidebug: add multiple device path instances on Boot####")
slightly tweaked the efidebug syntax adding -b, -i and -s for the boot
image, initrd and optional data.
The pytests using this command were adapted as well. However I completely
missed the last "" argument, which at the time indicated the optional data
and needed conversion as well.  This patch is adding the missing -s flag
and the tests are back to normal.

Fixes: cbea241e("efidebug: add multiple device path instances on Boot####")
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviwed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

In case of failure at efi_get_variable_int("BootOrder"), we should
skip examining boot option variables and return an appropriate error
code which is the one the function returned.

Fixes: CID 331153 Code maintainability issues  (UNUSED_VALUE)
Signed-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Indicated by Coverity Scan CID 331147

The ESRT was being refreshed in situations where the UpdateCapsule
procedure failed. In that scenario:

1) the ESRT refresh was superfluous.
2) a failed ESRT refresh return code overwrites the UpdateCapsule error
return code.

This commit ensures that the ESRT is only refreshed when the
UpdateCapsule performs successfully.

CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
CC: Tom Rini <trini@konsulko.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: nd@arm.com
Signed-off-by: NJose Marinho <jose.marinho@arm.com>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Bumping the digest list count, for all supported algorithms,  can be
calculated outside of the individual switch statements.  So let's do that
for every loop iteration instead and simplify the code a bit.
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

To avoid diverging function definitions we need to include efi_loader.h.

Fixes: fe179d7f ("efi_loader: Add size checks to efi_create_indexed_name()")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Due to copy-paste error, two of the setexpr arguments were missing.
Add the missing arguments.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Provide a man-page for the fatinfo command.

The .rst file was lost in patch 15d96946 ("doc: fatinfo man-page").

Fixes: 15d96946 ("doc: fatinfo man-page")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>