- 01 1月, 2018 4 次提交
-
-
由 Derald D. Woods 提交于
This commit clears 'ethaddr' before calling 'smc911x_initialize' to allow the SROM MAC address to be assigned properly. Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>
-
由 Derald D. Woods 提交于
This commit updates the configuration files needed to support OF_CONTROL on the OMAP3 EVM baseboard. Additionally: - CONFIG_SYS_THUMB_BUILD is enabled - CONFIG_SPL_ENV_SUPPORT is enabled Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb]. Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>
-
由 Derald D. Woods 提交于
This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note that this is the first addition of OMAP34XX devicetree files. Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>
-
由 Derald D. Woods 提交于
This commit keeps the 'fdtaddr' as provided by DEFAULT_LINUX_BOOT_ENV. Signed-off-by: NDerald D. Woods <woods.technical@gmail.com>
-
- 29 12月, 2017 20 次提交
-
-
-
由 Patrick Bruenn 提交于
Since commit 999a78d5 ("scripts/dtc: Update to upstream version v1.4.5-3-gb1a60033c110") dtc warns about: arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/serial@53fc0000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/ccm@53fd4000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/gpio@53fe4000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/sdma@63fb0000 arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/ethernet@63fec000 Fix this by adding a node for the tzic interrupt controller. Copied from "<Linux>/arch/arm/boot/dts/imx53.dts" Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Marek Vasut 提交于
The DDR DRAM calibration doesn't work on T-topology sometimes, so disable it. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
由 Vagrant Cascadian 提交于
In commit 6e6cf015 ("Merge git://www.denx.de/git/u-boot-imx") the line defining spl_sd configuration for wandboard was removed, which resulted in no SPL target being built. Add it back. Signed-off-by: NVagrant Cascadian <vagrant@debian.org> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Breno Lima 提交于
Currently CONFIG_SECURE_BOOT is selecting FSL_CAAM for all i.MX devices, this causes the following error when building mx6sl boards since this SoC doesn't have the CAAM block: In file included from drivers/crypto/fsl/jobdesc.c:12:0: drivers/crypto/fsl/jobdesc.c: In function 'inline_cnstr_jobdesc_blob_dek': include/fsl_sec.h:268:25: error: 'CAAM_ARB_BASE_ADDR' undeclared (first use in this function) #define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000) ^ drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1' memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz); ^ include/fsl_sec.h:268:25: note: each undeclared identifier is reported only once for each function it appears in #define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000) ^ drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1' memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz); ^ scripts/Makefile.build:280: recipe for target 'drivers/crypto/fsl/jobdesc.o' failed make[3]: *** [drivers/crypto/fsl/jobdesc.o] Error 1 scripts/Makefile.build:425: recipe for target 'drivers/crypto/fsl' failed make[2]: *** [drivers/crypto/fsl] Error 2 scripts/Makefile.build:425: recipe for target 'drivers/crypto' failed make[1]: *** [drivers/crypto] Error 2 Add HAS_CAAM configuration to avoid this error. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Breno Lima 提交于
MX6UL contains features that MX6ULL doesn't support. Deselect CONFIG_MX6UL and select SYS_L2CACHE_OFF and ROM_UNIFIED_SECTIONS. The motivation for doing this change is that MX6UL supports CAAM and MX6ULL does not. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Breno Lima 提交于
Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS, but it is better to select it directly via Kconfig. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
由 Breno Lima 提交于
Secure boot is not enabled in warp imximage.cfg, add support for it. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Breno Lima 提交于
Secure boot is not enabled in mx6slevk imximage.cfg, add support for it. Signed-off-by: NBreno Lima <breno.lima@nxp.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Acked-by: NPeng Fan <peng.fan@nxp.com>
-
由 Fabio Estevam 提交于
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the correct dtb is imx6sx-sdb-reva.dtb, so make this possible. While at it, remove an extra 'mmc dev'. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
NXP development boards based on i.MX6/i.MX7 contain the board revision information stored in the fuses. Introduce a common function that can be shared by different boards and convert mx6sabreauto to use this new mechanism. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Lukasz Majewski 提交于
This commit switch display5_factory_defconfig to use new, generic USE_BOOTCOMMAND Kconfig option. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Peng Fan 提交于
Include dm/ofnode.h. Signed-off-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Christopher Spinrath 提交于
Commit 5248930e ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for MMC. Remove the old mmc init code, which is no longer used, from the board file. Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Christopher Spinrath 提交于
Commit 5248930e ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for AHCI. Remove the old, now unused, sata init code from the board file. Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Christopher Spinrath 提交于
Commit 5248930e ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for USB. But it missed to enable driver model support for keyboards. As a result, USB keyboards do no longer work. Fix this by enabling driver model support for keyboards. Fixes: 5248930e ("dm: imx: cm_fx6: Enable more driver model support") Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Christopher Spinrath 提交于
Commit 5248930e ("dm: imx: cm_fx6: Enable more driver model support") enabled driver model support for USB, thereby effectively removing USB support because the cm_fx6 devicetree in the U-Boot does *not* enable the USB nodes. Reinstate the USB support by syncing the devicetree with Linux whose devicetree enables the USB nodes properly. More precisely, use the devicetree found in Linux v4.15-rc1 with the following two changes: 1) Remove the audio mux; the required dt-bindings header is not present in the U-Boot. 2) Keep the usdhc3 MMC controller node currently present in the U-Boot's devicetree to retain the ability to boot from MMC. Fixes: 5248930e ("dm: imx: cm_fx6: Enable more driver model support") Signed-off-by: NChristopher Spinrath <christopher.spinrath@rwth-aachen.de> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Martyn Welch 提交于
We are going to be using check_time() on more than the mx53ppd, move this function to a common location. Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
-
由 Adam Ford 提交于
There is an #ifdef and #endif with nothing in between. This patch simply removes this dead/useless code. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Fabio Estevam 提交于
In order to provide a consistent user experience for imx board users, remove the custom CONFIG_BOOTDELAY values from defconfig files, so that all boards can use the default two second delay. Signed-off-by: NFabio Estevam <festevam@gmail.com> Reviewed-by: NLukasz Majewski <lukma@denx.de>
-
- 27 12月, 2017 2 次提交
-
-
-
由 Masahiro Yamada 提交于
Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 25 12月, 2017 3 次提交
-
-
由 Prabhakar Kushwaha 提交于
Linux device tree contains "ethernet" node for all possible interface supported by SoC i.e. LS1046A. It is not necessary for a SerDes protocol to support all possible interface. So disable unavailable "ethernet" node in device tree. Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address sequentially from environment variables Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Prabhakar Kushwaha 提交于
"ethernet" node fix-up for device tree happens before Linux boot. There can be requirement of updating "ethernet" node even before fix-up. So, add support of updating "ethernet" node. Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Prabhakar Kushwaha 提交于
The MAC addresses get fixed in the device tree for "ethernet" nodes is by using trailing number behind "ethernet" found in "/aliases". It may not be necessary for the "ethernet" nodes to be sequential. There can be gaps in between or any node disabled So provide a support to fetch MAC addr sequentially from env and apply them to "ethernet" nodes in the order they appear in device tree only if "ethernet" is not "disabled" Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 21 12月, 2017 2 次提交
-
-
-
由 Andy Shevchenko 提交于
FLIS IP since now gets its own ACPI ID. Drop PRP0001 workaround in favour of official ACPI HID. Corresponding kernel commit dabd4bc6de2b pinctrl: intel: merrifield: Introduce ACPI device table in the pin control subsystem tree [1] targeting v4.16. [1]: https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=dabd4bc6de2bReviewed-by: NBin Meng <bmeng.cn@gmail.com> Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
-
- 19 12月, 2017 9 次提交
-
-
-
-
由 Emmanuel Vadot 提交于
When adding a partition, set the logical_partition member in the media structure as mandated by the UEFI spec. Signed-off-by: NEmmanuel Vadot <manu@freebsd.org> Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Sean Nyekjaer 提交于
This spi-nor is 4Mbit/512KB Fixes: b4fbcbc5 ("mtd/spi: add support for is25lq040b") Signed-off-by: NSean Nyekjaer <sean.nyekjaer@prevas.dk> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Jagan Teki 提交于
Order sun50i-h5-orangepi-prime.dts nodes in alphabetic Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Jagan Teki 提交于
Now FASTBOOT_FLASH is auto select for sunxi platform, so drop explicit addition. Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Jagan Teki 提交于
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error when uncompressing Image.gz out of FIT image. Uncompressing Kernel Image ... Error: inflate() returned -5 Image too large: increase CONFIG_SYS_BOOTM_LEN and loading Image out of FIT image. Loading Kernel Image ... Image too large: increase CONFIG_SYS_BOOTM_LEN Must RESET board to recover Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-