- 25 6月, 2007 4 次提交
-
-
由 Niklaus Giger 提交于
This patch fixes the problem to assemble cpu/ppc4xx/start.S experienced last week where building failed having specified O=../build.sequoia. Signed-off-by: NNiklaus Giger <niklaus.giger@nestal.com>
-
由 Stefan Roese 提交于
This patch removes the CFG_PCI_PRE_INIT option completely, since it's not needed anymore with the patch from Matthias Fuchs with the "weak" pci_pre_init() implementation. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
-add pci_pre_init() for pci interrupt fixup code -disable phy sleep mode via reset_phy() function -use correct io accessors -cleanup Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
-
由 Matthias Fuchs 提交于
This patch adds support for calling a plattform dependant pci_pre_init() function for 405 boards. This can be used to move the current pci_405gp_fixup_irq() function into the board code. This patch also makes the CFG_PCI_PRE_INIT define obsolete. A default function with 'weak' attribute is used when a board specific pci_pre_init() is not implemented. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
-
- 22 6月, 2007 2 次提交
-
-
由 Stefan Roese 提交于
The recently extended program_tlb() function had a problem when multiple TLB's had to be setup (for example with 512MB of SDRAM). The virtual address was not incremented. This patch fixes this issue and is tested on Katmai with 512MB SDRAM. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Rafal Jaworowski 提交于
- adapt to the more generic EXCEPTION_PROLOG and CRIT_EXCEPTION macros - minor 4xx cleanup
-
- 21 6月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 20 6月, 2007 1 次提交
-
-
- 19 6月, 2007 4 次提交
-
-
由 Stefan Roese 提交于
This patch adds a board command to configure the I2C bootstrap EEPROM values. Right now 533 and 667MHz are supported for booting either via NOR or NAND FLASH. Here the usage: => bootstrap 533 nor ;to configure the board for 533MHz NOR booting => bootstrap 667 nand ;to configure the board for 667MHz NNAND booting Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
The latest changes showed a problem with the location of the NAND-SPL image in the OCM and the init-data area (incl. cache). This patch fixes this problem. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Wolfgang Denk 提交于
-
- 15 6月, 2007 5 次提交
-
-
由 Stefan Roese 提交于
Now CONFIG_440 has to be defined in all PPC440 board config files. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
-
由 Grzegorz Bernacki 提交于
- Introduced dedicated switches for building 440 and 405 images required for 440-specific machine instructions like 'rfmci' etc. - Exception vectors moved to the proper location (_start moved away from the critical exception handler space, which it occupied) - CriticalInput now serviced (with default handler) - MachineCheck properly serviced (added a dedicated handler and return subroutine) - Overall cleanup of exceptions declared with STD_EXCEPTION macro (unused, unhandled and those not relevant for 4xx were eliminated) - Eliminated Linux leftovers, removed dead code Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com> Signed-off-by: NRafal Jaworowski <raj@semihalf.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch adds initial support for the Liebherr lwmon5 board euqipped with an AMCC 440EPx PowerPC. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
The board config array CFG_440_GPIO_TABLE for the ppc440 GPIO setup is extended with the default GPIO output state (level). Signed-off-by: NStefan Roese <sr@denx.de>
-
- 14 6月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
Now program_tlb() allows to program a TLB (or multiple) with different virtual and physical addresses. With this change, now one physical region (e.g. SDRAM) can be mapped 2 times, once with caches diabled and once with caches enabled. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 12 6月, 2007 2 次提交
-
-
由 Detlev Zundel 提交于
Most prominently this changes 'erase' to be non-repeatable. Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
由 Detlev Zundel 提交于
Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
- 08 6月, 2007 3 次提交
-
-
由 Bartlomiej Sieka 提交于
Signed-off-by: NJan Wrobel <wrr@semihalf.com> Acked-by: NBartlomiej Sieka <tur@semihalf.com>
-
由 Wolfgang Denk 提交于
-
由 Benoît Monin 提交于
Set the correct value in GPIOx_TCR when configuring the gpio with CFG_440_GPIO_TABLE. Signed-off-by: NBenoit Monin <bmonin@adeneo.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 06 6月, 2007 7 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Stefan Roese 提交于
-
由 Stefan Roese 提交于
This patch adds NAND booting support for the AMCC Acadia eval board. Please make sure to configure jumper J7 to position 2-3 when booting from NOR, and to position 1-2 when booting for NAND. I also added a board command to configure the I2C bootstrap EEPROM values. Right now only 267MHz is support for booting either via NOR or NAND FLASH. Here the usage: => bootstrap 267 nor ;to configure the board for 267MHz NOR booting => bootstrap 267 nand ;to configure the board for 267MHz NNAND booting Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Jon Loeliger 提交于
-
由 Ed Swarthout 提交于
e600 does not have a bootpg restriction. Move the version string to beginning of image at fff00000. Resetvec.S is not needed. Update flash copy instructions. Add tftpflash env variable Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: NJon Loeliger <jdl@freescale.com>
-
- 05 6月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 04 6月, 2007 1 次提交
-
-
由 Benoît Monin 提交于
The attached patch is mainly cosmetic, allowing u-boot to display the correct bootstrap option letter according to the datasheets. The original patch was extended with 405EZ support by Stefan Roese. Signed-off-by: NBenoit Monin <bmonin@adeneo.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 01 6月, 2007 8 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
-
由 Stefan Roese 提交于
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As suggested by AMCC it is not recommended to dynamically change the EBC speed after bootup. So we undo this change to be on the safe side. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch adds NAND booting support for the AMCC Bamboo eval board. Since the NAND-SPL boot image is limited to 4kbytes, this version only supports the onboard 64MBytes of DDR. The DIMM modules can't be supported, since the setup code for I2C DIMM autodetection and configuration is too big for this NAND bootloader. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
The U-Boot NAND booting support is now extended to support ECC upon loading of the NAND U-Boot image. Tested on AMCC Sequoia (440EPx) and Bamboo (440EP). Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch updates the "normal" Bamboo NOR booting port, so that it is compatible with the coming soon NAND booting Bamboo port. It also enables the 2nd NAND flash on the Bamboo. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-