- 06 6月, 2013 1 次提交
-
-
由 Fabio Estevam 提交于
When running the "save" command several times on a mx6qsabresd we see: U-Boot > save Saving Environment to MMC... Writing to MMC(1)... done U-Boot > save Saving Environment to MMC... MMC partition switch failed U-Boot > save Saving Environment to MMC... Writing to MMC(1)... done U-Boot > save Saving Environment to MMC... MMC partition switch failed U-Boot > save Saving Environment to MMC... Writing to MMC(1)... done U-Boot > save Saving Environment to MMC... MMC partition switch failed This issue is caused by the incorrect usage of CONFIG_SYS_MMC_ENV_PART. CONFIG_SYS_MMC_ENV_PART should be used to specify the mmc partition that stores the environment variables. On some imx boards it is been incorrectly used to pass the partition of kernel and dtb files for the 'mmcpart' script variable. Remove the CONFIG_SYS_MMC_ENV_PART usage and configure the 'mmcpart' variable directly. Reported-by: NJason Liu <r64343@freescale.com> Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NJason Liu <r64343@freescale.com>
-
- 03 6月, 2013 1 次提交
-
-
由 Renato Frias 提交于
Add i2c2 and 3 to mx6qsabreauto board, i2c3 is multiplexed use gpio to set steering. Signed-off-by: NRenato Frias <b13784@freescale.com> Reviewed-by: NOtavio Salvador <otavio@ossystems.com.br> Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
- 28 1月, 2013 2 次提交
-
-
由 Fabio Estevam 提交于
commit 49ea0ff5 (49ea0ff5) introduced CONFIG_SYS_MMC_ENV_PART into mx6qsabresd.h to store the mmc partition, but in order for it to have effect we should place it into 'mmcpart' variable. Also add CONFIG_SYS_MMC_ENV_PART into mx6qsabreauto.h. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Knut Wohlrab 提交于
The USB host interface is routed to plug USB1/J30 on the mother board. Signed-off-by: NKnut Wohlrab <knut.wohlrab@de.bosch.com>
-
- 13 1月, 2013 1 次提交
-
-
由 Otavio Salvador 提交于
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 06 1月, 2013 1 次提交
-
-
由 Shawn Guo 提交于
The on-board number of available usdhc devices is something board specific. The patch moves CONFIG_SYS_FSL_USDHC_NUM out of mx6qsabre_common.h and adds usdhc2 and usdhc4 support for mx6qsabresd board. To keep the default mmc device for environment same as before (usdhc3), it moves CONFIG_SYS_MMC_ENV_DEV out of mx6qsabre_common.h and changes it to 1 for mx6qsabresd. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 16 10月, 2012 3 次提交
-
-
由 Otavio Salvador 提交于
The mmcroot setting vary between mx6qsabreauto and mx6qsabresd so we move this to the board configuration file. Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Acked-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Otavio Salvador 提交于
The mx6qsabreauto console is different than mx6qsabresd so the console configuration is now set in the board file. Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Fabio Estevam 提交于
mx6qsabreauto is a board based on mx6q SoC with the following features: - 2GB of DDR3 - 2 USB ports - 1 HDMI output port - SPI NOR - 2 LVDS LCD ports - Gigabit Ethernet - Camera - eMMC and SD card slot - Multichannel Audio - CAN - SATA - NAND - PCIE - Video Input Add very basic support for it. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-