- 05 6月, 2020 1 次提交
-
-
由 Tom Rini 提交于
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 5月, 2020 1 次提交
-
-
由 Simon Glass 提交于
Move this uncommon header out of the common header. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 09 5月, 2020 1 次提交
-
-
由 Ashok Reddy Soma 提交于
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 1月, 2020 1 次提交
-
-
由 Rasmus Villemoes 提交于
This complements commit 06878977 which did the conversion for mpc85xx. Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: NMario Six <mario.six@gdsys.cc>
-
- 21 11月, 2019 2 次提交
-
-
由 Tom Rini 提交于
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
由 Tom Rini 提交于
We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one board where we can simply multiple CONFIG_ENV_SIZE by two for the same result. The other place where we could but were not previously using this is for where env_internal.h checks for if we should set ENV_IS_EMBEDDED. This seems like the most likely use, historically, of the variable, but it was not used. Add logic to check for this now. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 21 5月, 2019 15 次提交
-
-
由 Mario Six 提交于
Except for one counter example, CONFIG_SYS_LBC_LBCR always has a value of either 0x00040000 or 0x00000000. CONFIG_SYS_LBC_MRTPR always has the value 0x20000000. CONFIG_SYS_LBC_LSDMR_{1,2,4,5} are not set for any mpc83xx board. CONFIG_SYS_LBC_LSRT is set by one board (to 0x32000000). To simplify the configuration files, hardcode the setting of these values for mpc83xx. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as CONFIG_SYS_SDRAM_BASE on all existing boards. Just use CONFIG_SYS_SDRAM_BASE instead. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
CONFIG_SYS_DDR_BASE is specific to mpc83xx an is always set to the same value as CONFIG_SYS_SDRAM_BASE. Just use CONFIG_SYS_SDRAM_BASE instead. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the CONFIG_LCRR_* settings to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the arbiter configuration to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate CONFIG_SYS_IMMR to Kconfig for MPC83xx. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Mirate the HID configuration settings to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the BR/OR settings to Kconfig. These must be known at compile time, so cannot be configured via DT. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Re-format all BR,OR #define lines into single lines. This makes them harder to read, but accessible to semi-automatic replacement. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
The LBLAW_* values determine the window configuration of the memory controller. Hence, they must be known at compile time, and cannot be implemented in the DT mechanism. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
The BATs (block address translation registers) determine the initial memory window mappings. Hence, they must be known at compile time and cannot be implemented in the DT mechanism. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the CONFIG_HIGH_BATS variable to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
The HRCW (hardware reset configuration word) is a constant that must be hard-coded into the boot loader image. So, it must be available at compile time, and cannot be migrated to the DT mechanism, but has to be kept in Kconfig. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the system clock. To migrate the architecture, we can replace CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ. To do this * replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ * set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all MPC83xx config files Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
The ve8313 has the option of either configuring the eLBC (enhanced local system bus) such that * NOR flash is the first memory bank, and NAND flash is the second memory bank, or * NAND flash is the first memory bank, and NOR flash is the second memory bank, by using CONFIG_SYS_NOR_{BR,OR}_PRELIM and CONFIG_SYS_NAND_{BR,OR}_PRELIM for defining CONFIG_SYS_{BR,OR}{0,1}_PRELIM. After Kconfig migration, replacing some lines in the defconfig will have the same effect. Hence, we will not create distinct ve8313_{NOR,NAND} configs for such a small change. Instead, fix the current default (NOR first, NAND second), and unroll the CONFIG_SYS_NAND_{BR,OR}_PRELIM options. This will ease the Kconfig migration Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 20 5月, 2019 1 次提交
-
-
由 Mario Six 提交于
Replace CONFIG_MPC833* with proper CONFIG_ARCH_MPC833* Kconfig options. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 20 10月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 07 5月, 2018 1 次提交
-
-
由 Tom Rini 提交于
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 4月, 2018 2 次提交
-
-
由 Mario Six 提交于
CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every use is couched by __stringify(...). Hence, convert it to a proper string option. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 16 3月, 2018 1 次提交
-
-
由 Tom Rini 提交于
This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 2月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 20 1月, 2018 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
The following config symbols are only defined once and never referenced anywhere else: CONFIG_CYRUS CONFIG_IDS8313 CONFIG_MPC8308_P1M CONFIG_MPC8308RDB CONFIG_MPC8349EMDS CONFIG_MPC8349ITXGP CONFIG_SBC8349 CONFIG_SBC8548 CONFIG_SBC8641D CONFIG_TQM834X CONFIG_VE8313 CONFIG_XPEDITE5140 CONFIG_XPEDITE5200 CONFIG_XPEDITE550X Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com> Acked-by: NMario Six <mario.six@gdsys.cc>
-
- 04 9月, 2017 2 次提交
-
-
由 Thomas Petazzoni 提交于
Now that include/config_fallbacks.h define a sane fallback for CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all configurations that were using the default value. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Thomas Petazzoni 提交于
Now that the fallback value of CONFIG_SYS_PBSIZE in include/config_fallbacks.h has been adjusted, remove its definition from a large number of board configuration files. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 12 8月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_PCI Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 01 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the defconfig files. Tested-by: NAdam Ford <aford173@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
- 26 7月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_ENV_IS_IN_FLASH Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 20 3月, 2017 1 次提交
-
-
由 Philipp Tomsich 提交于
Move this in to Kconfig with a default of 115200. Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> [trini: Run moveconfig.py, reword commit slightly] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 1月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_BOARD_EARLY_INIT_F Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 28 10月, 2016 2 次提交
-
-
由 Bin Meng 提交于
Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig to use that. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NTom Rini <trini@konsulko.com> [trini: Re-generate configs and include/configs/ changes] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Add 'PCI' as a menu option and migrate all existing users. Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NStephen Warren <swarren@nvidia.com>
-
- 12 10月, 2016 1 次提交
-
-
由 Lokesh Vutla 提交于
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default in certain architectures. Migrate all config files. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-