This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_ASKENV
   CONFIG_CMD_BMP
   CONFIG_CMD_BOOTD
   CONFIG_CMD_CACHE
   CONFIG_CMD_CRC32
   CONFIG_CMD_DHCP
   CONFIG_CMD_ENV
   CONFIG_CMD_EXPORTENV
   CONFIG_CMD_EXT2
   CONFIG_CMD_EXT4
   CONFIG_CMD_FLASH
   CONFIG_CMD_FS_GENERIC
   CONFIG_CMD_FUSE
   CONFIG_CMD_GPIO
   CONFIG_CMD_GPT
   CONFIG_CMD_GREPENV
   CONFIG_CMD_I2C
   CONFIG_CMD_IMLS
   CONFIG_CMD_IMPORTENV
   CONFIG_CMD_LOADB
   CONFIG_CMD_LOADS
   CONFIG_CMD_MEMINFO
   CONFIG_CMD_MII
   CONFIG_CMD_MTDPARTS
   CONFIG_CMD_NAND
   CONFIG_CMD_NAND_TRIMFFS
   CONFIG_CMD_NFS
   CONFIG_CMD_PCA953X
   CONFIG_CMD_PCA953X_INFO
   CONFIG_CMD_PCI
   CONFIG_CMD_PING
   CONFIG_CMD_READ
   CONFIG_CMD_SF
   CONFIG_CMD_SPI
   CONFIG_CMD_SPL
   CONFIG_CMD_SPL_WRITE_SIZE
   CONFIG_CMD_TIME
   CONFIG_CMD_TRACE
   CONFIG_CMD_UBI
   CONFIG_CMD_UBIFS
   CONFIG_CMD_UNZIP
   CONFIG_FS_EXT4
Signed-off-by: NTom Rini <trini@konsulko.com>

Move this uncommon header out of the common header.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: NTom Rini <trini@konsulko.com>

This complements commit 06878977 which did the conversion for
mpc85xx.
Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: NMario Six <mario.six@gdsys.cc>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Except for one counter example, CONFIG_SYS_LBC_LBCR always has a value
of either 0x00040000 or 0x00000000.

CONFIG_SYS_LBC_MRTPR always has the value 0x20000000.

CONFIG_SYS_LBC_LSDMR_{1,2,4,5} are not set for any mpc83xx board.

CONFIG_SYS_LBC_LSRT is set by one board (to 0x32000000).

To simplify the configuration files, hardcode the setting of these
values for mpc83xx.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

CONFIG_SYS_DDR_SDRAM_BASE is set to the same value as
CONFIG_SYS_SDRAM_BASE on all existing boards. Just use
CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

CONFIG_SYS_DDR_BASE is specific to mpc83xx an is always set to the same
value as CONFIG_SYS_SDRAM_BASE. Just use CONFIG_SYS_SDRAM_BASE instead.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Migrate the CONFIG_LCRR_* settings to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Migrate the arbiter configuration to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Migrate CONFIG_SYS_IMMR to Kconfig for MPC83xx.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Mirate the HID configuration settings to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.

Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Re-format all BR,OR #define lines into single lines. This makes them
harder to read, but accessible to semi-automatic replacement.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

All BR/OR option lines should have the same layout to make them easier
to migrate to Kconfig. This includes using the same option macros
everywhere.

The normalize the lines,
* replace function macros with their results, and
* replace hardcoded hex values with standard macros
Signed-off-by: NMario Six <mario.six@gdsys.cc>

The LBLAW_* values determine the window configuration of the memory
controller. Hence, they must be known at compile time, and cannot be
implemented in the DT mechanism.

Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

The BATs (block address translation registers) determine the initial
memory window mappings. Hence, they must be known at compile time and
cannot be implemented in the DT mechanism.

Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Migrate the CONFIG_HIGH_BATS variable to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

The HRCW (hardware reset configuration word) is a constant that must be
hard-coded into the boot loader image. So, it must be available at
compile time, and cannot be migrated to the DT mechanism, but has to be
kept in Kconfig.

Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the
system clock. To migrate the architecture, we can replace
CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ.

To do this
* replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ
* set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all
  MPC83xx config files
Signed-off-by: NMario Six <mario.six@gdsys.cc>

CONFIG_MPC8313ERDB is unused, and
TARGET_MPC8313ERDB_NAND/TARGET_MPC8313ERDB_NOR Kconfig could replace it.

Hence, get rid of CONFIG_MPC8313ERDB.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

MPC8313ERDB has the option of either enabling NOR or NAND boot in its
config file (by commenting out certain #ifdefs). To keep this ability
after migrating options to Kconfig, we introduce two MPC8313ERDB
configs: one for NOR, and one for NAND.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Replace CONFIG_MPC833* with proper CONFIG_ARCH_MPC833* Kconfig options.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: NTom Rini <trini@konsulko.com>

NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

This converts the following to Kconfig:
   CONFIG_MISC_INIT_R
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE
Signed-off-by: NAdam Ford <aford173@gmail.com>

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: NTom Rini <trini@konsulko.com>

CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every
use is couched by __stringify(...).

Hence, convert it to a proper string option.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Migrate the CONFIG_TSEC_ENET option to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>

This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: NTom Rini <trini@konsulko.com>

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: NTom Rini <trini@konsulko.com>

We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.

Tested-by: Adam Ford <aford173@gmail.com>  #omap3_logic
Signed-off-by: NTom Rini <trini@konsulko.com>

Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_PCI
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.
Tested-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>