- 14 10月, 2019 11 次提交
-
-
由 Jun Nie 提交于
Support distro boot for pico imx7d in FIT image case. Signed-off-by: NJun Nie <jun.nie@linaro.org> Tested-by: NJoris Offouga <offougajoris@gmail.com>
-
由 Jun Nie 提交于
Add config to enable CAAM so that hardware random number generator works. Signed-off-by: NJun Nie <jun.nie@linaro.org>
-
由 Adam Ford 提交于
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with -u-boot.dtsi entries to include the pinmuxing in SPL, the manual code setting up the pinmux can go away. This patch removes the legacy pinmuxing code from the board file. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NFabio Estevam <festevam@gmail.com>
-
由 Adam Ford 提交于
With the 256KB of OCRAM available to SPL now, there should be enough room to enable the pinmuxing in SPL from the device tree. This patch enables SPL_PINCTRL et al and adds the serial and usdhc pin mux references to the -u-boot.dtsi file so the pins can be configured from the device tree. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NFabio Estevam <festevam@gmail.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
由 Adam Ford 提交于
Since this board config only supports, the i.MX6D/i.MX6Q configurations, 256K of on-chip RAM is available which increases the space available to SPL to help further reduce board code and further enable device tree functions. This patch enables 256K of RAM. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NFabio Estevam <festevam@gmail.com>
-
由 Soeren Moch 提交于
So we can remove lots of legacy config code. Signed-off-by: NSoeren Moch <smoch@web.de>
-
由 Soeren Moch 提交于
So we can get rid of legacy pci config code. PCI_PNP is not required for this board, remove it to reduce the size of the u-boot binary. DM_PCI does not start the host controller automatically anymore. Do so in preboot instead. Signed-off-by: NSoeren Moch <smoch@web.de>
-
由 Soeren Moch 提交于
Signed-off-by: NSoeren Moch <smoch@web.de>
-
由 Sjoerd Simons 提交于
Both the distro boot configuration as well as the general pxe support standardized on fdtfile as the variable to hold the dtb filename. Adjust to follow that such that e.g. "pxe boot" will just work. Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
-
由 Shawn Guo 提交于
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications. https://www.novtech.com/products/meerkat96.html https://www.96boards.org/product/imx7-96/ The initial supported/tested devices include: - Debug serial - SD - USB Host (with Ethernet) With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB. Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Tested-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-
由 Shawn Guo 提交于
It imports device tree source of meerkat96 board from Linux Kernel. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 13 10月, 2019 1 次提交
-
-
由 Tom Rini 提交于
We don't need to pull in anything from the MIPS job so exclude that from the new bcm job and make it clear it's building only ARM. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 10月, 2019 28 次提交
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-x86由 Tom Rini 提交于
- Remember the device being emulated for Sandbox PCI - Update Kconfig options for FSP 1.0 - Drop RESET_BASE and RESET_SEG_SIZE that are no longer used
-
由 Tom Rini 提交于
- Assorted cleanups - FAT bugfixes - mediatek platform updates
-
由 Tom Rini 提交于
- Various improvements to dra7xx, keystone 3, am65x SoCs - Platform updates - remoteproc improvements
-
由 Marek Szyprowski 提交于
Add support for quad (64bits) memory access specifier. Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com> Acked-by: NLukasz Majewski <lukma@denx.de>
-
由 Heinrich Schuchardt 提交于
If out of memory, return -1 and not -ENOMEM from get_contents(). Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Heinrich Schuchardt 提交于
When hitting an invalid FAT cluster while reading a file always print an error message and return an error code. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Tom Rini 提交于
At this point, all drivers that do not use CONFIG_BLK are past their migration deadlines, so remove this config as it's no longer helpful and hinders enhancing block drivers. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Lukasz Majewski 提交于
This define indicates if DM_SPI shall be supported in SPL. This allows proper operation of DM converted SPI drivers in SPL, which use #if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted boards. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Heinrich Schuchardt 提交于
If an exception occurs in a loaded image and the relocation offset is unknown, it is helpful to know the instructions pointed to by the program counter. This patch adds the missing output. A possible output is: Code: 910c4021 aa1303e0 f9400662 d63f0040 (e7f7defb) The parentheses indicate the instruction causing the exception. The output can be disassembled using scripts/decodecode: echo 'Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)' | \ ARCH=arm64 scripts/decodecode Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb) All code ======== 0: 90000360 adrp x0, 0x6c000 4: 9100b800 add x0, x0, #0x2e 8: 94002782 bl 0x9e10 c: 17ffff8f b 0xfffffffffffffe48 10:* e7f7defb .inst 0xe7f7defb ; undefined <-- trapping instruction Code starting with the faulting instruction =========================================== 0: e7f7defb .inst 0xe7f7defb ; undefined We already have implemented the same for armv7. For testing command 'exception undefined' can be used. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 T Karthik Reddy 提交于
This patch uses auto instead of decimal in simple_strtoul(). Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Rasmus Villemoes 提交于
readb is unconditionally defined earlier in io.h, so there's no point checking whether it's undefined. Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk>
-
由 Rasmus Villemoes 提交于
No ARM board seems to define __mem_pci - and if it did, one would get tons of ./arch/arm/include/asm/io.h:307:0: warning: "readl" redefined warnings, because readl and friends are unconditionally defined earlier in io.h. Moreover, the redefinitions lack the memory barriers that the first definitions have. So I'm guessing this is practically dead code. Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk>
-
由 Mans Rullgard 提交于
This change allows setting pre-defined eMMC boot partition for SPL eMMC booting. It is necessary in the case when one wants to boot (through falcon boot) from eMMC after loading SPL from other memory (like SPI-NOR). Signed-off-by: NMans Rullgard <mans@mansr.com> [lukma: Edit the commit message] Signed-off-by: NLukasz Majewski <lukma@denx.de> Acked-by: NAndreas Dannenberg <dannenberg@ti.com>
-
由 Mans Rullgard 提交于
This fixes a wrongly indented block of code. Signed-off-by: NMans Rullgard <mans@mansr.com> [lukma: Make the commit message more verbose] Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lokesh Vutla 提交于
If there is any failure during IOdelay recalibration sequence, IOs are not guaranteed to behave as expected. So hang on any failure during the sequence. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
When an error is reported in __recalibrate_iodelay_start(), de-isolation of IO doesn't happen. Because of this, undefined behaviour is observed on many peripherals without any error. So make sure io is out of isolation at the end of iodelay recalibration. Reported-by: NRichard Woodruff <r-woodruff2@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Jarkko Nikula 提交于
Currently "bootcmd" does not work as intended but instead prints MMC usage information and goes directly to "nandboot". Follow what the commit 66968110 ("configs: Fix usage of mmc rescan") does for other boards prior to support for TechNexion TAO3530 SoM was added. Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
-
由 Lokesh Vutla 提交于
spl_dm_init is failing as usb to be probed with the following error: "omap_dwc3@483c0000: ret=-2" Enable usb to make spl boot on am43xx devices Reported-by: NTero Kristo <t-kristo@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Main uart0 is used as debug console by both R5SPL and A72 bootloader and Linux. So mark it as shared device so that power-domain request is successful by both cores. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Tero Kristo 提交于
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: NTero Kristo <t-kristo@ti.com>
-
由 Tero Kristo 提交于
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: NTero Kristo <t-kristo@ti.com>
-
由 Tero Kristo 提交于
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: NTero Kristo <t-kristo@ti.com>
-
由 Tero Kristo 提交于
Add support for CDCE913/925/937/949 family of devices. These are modular PLL-based low cost, high performance, programmable clock synthesizers, multipliers and dividers. They generate up to 9 output clocks from a single input frequency. The initial version of the driver does not support programming of the PLLs, and thus they run in the bypass mode only. The code is loosely based on the linux kernel cdce9xx driver. Signed-off-by: NTero Kristo <t-kristo@ti.com>
-
由 Lokesh Vutla 提交于
Use the driver name to get ti_sci handle rather than relying on just the FIRMWARE uclass. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Enable CONFIG_DISPLAY_CPUINFO so that cpuinfo is printed during boot. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Enable CONFIG_DISPLAY_CPUINFO so that cpuinfo is printed during boot. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Print the board name and ver along with the DT Model. While at it print the ver for all the detected daughter cards. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
Add support for printing CPU info for all K3 devices. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-