- 05 4月, 2017 12 次提交
-
-
由 Andre Przywara 提交于
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores. To allow sharing the clocks, GPIO and driver code easily, create an architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol. Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and let it be selected by a new shared Kconfig option. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Andre Przywara 提交于
The DRAM controller in the Allwinner H5 SoC is again very similar to the one in the H3 and A64. Based on the existing socid parameter, add support for this controller by reusing the bulk of the code and only deviating where needed. These new bits set or cleared here and there have been mostly found by looking at DRAM register dumps after using the H5 boot0 and comparing them to what we set in the code. So for now it's mostly unclear what those bits actually mean - hence the missing names and comments. Also add the delay line parameters taken from the boot0 and libdram disassembly. Register setup differences between H5 and H3 are courtesy of Jens Kuske. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Andre Przywara 提交于
Addresses passed on to readl and writel are expected to be of the same size as a pointer. Change the parameter types of sunxi_spi0_read_data() to make the compiler happy and allow a warning-free aarch64 compile. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Andre Przywara 提交于
Every armv8 board needs the memory map, so change the #ifdef to ARM64 to avoid enumerating every single board or SoC. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Andre Przywara 提交于
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB, while the first SRAM region is mapped at address 0. With the extended physical memory support of the A80 this was changed, so the BROM is now at address 0 and the SRAM region starts right behind this at 64KB. This configuration seems to be called "high SRAM". Instead of enumerating the SoCs which have copied this configuration, let's call a spade a spade and introduce a Kconfig option for this setup. SoCs implementing this (A80, A64 and H5, so far), can then select this configuration. Simplify the config header definition on the way. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Andre Przywara 提交于
For some reason we were pretty conservative when defining the maximum SPL size for the Allwinner A80(sun9i) SoC. According to the manual the SRAM A1 is even 40KB, but the BROM probably still has the 32 KiB load limit. For the sake of simplicity, merge the SPL memory definitions for the A64 and A80 SoCs, since both SoC share the BROM/SRAM A1 memory layout. This helps to further simplify this is in the next patch. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Andre Przywara 提交于
Instead of enumerating all SoC families that need that bit set, let's just express this more clearly: The SMP bits needs to be set on SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the other way round, so we use ! CPU_IS_UP and ! ARM64. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Andre Przywara 提交于
Some Freescale boards used an extra version of the constant to hold the Generic Timer frequency. This can easily be covered by the now unified COUNTER_FREQUENCY constant, so remove this extra variable from those boards. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NYork Sun <york.sun@nxp.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Andre Przywara 提交于
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the frequency of the ARM Generic Timer (aka. arch timer). ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same purpose. It seems useful to unify them. Since there are less occurences of the latter version, lets convert all users over to COUNTER_FREQUENCY. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Andre Przywara 提交于
If we take the liberty to use register r0 to perform our bit set, we should be nice enough to tell the compiler about it. Add r0 to the clobber list to avoid potential mayhem. Signed-off-by: NAndre Przywara <andre.przywara@arm.com> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Acked-by: NJagan Teki <jagan@openedev.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
- 04 4月, 2017 6 次提交
-
-
git://git.denx.de/u-boot-arc由 Tom Rini 提交于
In this patch-set we add support of new AXS103 firmware as well as troubleshoot unexpected execution by multiple cores simultaneously.
-
-
-
git://www.denx.de/git/u-boot-marvell由 Tom Rini 提交于
This includes Marvell mvpp2 patches with the ethernet support for the ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe and he is okay with me pushing them via the Marvell tree.
-
-
-
- 02 4月, 2017 3 次提交
-
-
由 Marcel Ziswiler 提交于
Actually make use of that shiny new CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK. Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Marcel Ziswiler 提交于
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0 register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM. Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
由 Marcel Ziswiler 提交于
This patch adds board support for the Toradex Apalis TK1 a computer on module which can be used on different carrier boards. The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec. Furthermore, there is a Kinetis MK20DN512 companion micro controller for analogue, CAN and resistive touch functionality. For the sake of ease of use we do not distinguish between different carrier boards for now as the base module features are deemed sufficient enough for regular booting. The following functionality is working so far: - eMMC boot, environment storage and Toradex factory config block - Gigabit Ethernet - MMC/SD cards (both MMC1 as well as SD1 slot) - USB client/host (dual role OTG port as client e.g. for DFU/UMS or host, other two ports as host) Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com> Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 01 4月, 2017 3 次提交
-
-
由 Alexey Brodkin 提交于
Even though we expect only master core to execute U-Boot code let's make sure even if for some reason slave cores attempt to execute U-Boot in parallel with master they get halted very early. If platform wants it may kick-start slave cores before passing control to say Linux kernel or any other application that want to see all cores of SMP SoC up and running. Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
由 Alexey Brodkin 提交于
In axs103 v1.1 procedure to kick-start slave cores has changed quite a bit compared t previous implementation. In particular: * We used to have a generic START bit for all cores selected by CORE_SEL mask. But now we don't touch CORE_SEL at all because we have a dedicated START bit for each core: bit 0: Core 0 (master) bit 1: Core 1 (slave) * Now there's no need to select "manual" mode of core start Additional challenge for us is how to tell which axs103 firmware we're dealing with. For now we'll rely on ARC core version which was bumped from 2.1c to 3.0. Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
由 Alexey Brodkin 提交于
* Rely on default pulse polarity value * Don't mess with "multicore" value as it doesn't affect execution In essence we now do a bare minimal stuff: 1) Select HS38x2_1 with CORE_SEL=1 bits 2) Select "manual" core start (via CREG) with START_MODE=0 3) Generate cpu_start pulse with START=1 Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
- 30 3月, 2017 4 次提交
-
-
由 Jean-Jacques Hiblot 提交于
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jean-Jacques Hiblot 提交于
This is a preparation work for the support of CONFIG_BLK. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jean-Jacques Hiblot 提交于
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jean-Jacques Hiblot 提交于
For consistency, use an accessor to access the private data. Also for the same reason, rename all priv_data to priv. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 29 3月, 2017 12 次提交
-
-
由 Stefan Roese 提交于
The Marvell PHY support is needed espescially for the A7040-DB with the SGMII port (port 2). As without the marvell PHY driver configuration for SGMII, ethernet won't work. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
The default configuration for the COMPHY-0 port should be 1G, as its used as 1G SGMII connection. This change is necessary to get the MAC2 port (SGMII) working on this DB. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
As pointed out by Stefan Chulski, this variable is unused and should be removed. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
On PPv2.2 we enable PHY polling, so we also need to configure the PHY address in the specific PHY address rgisters. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
Testing shows, that PHY polling needs to be enabled on Armada 7k/8k. Otherwise ethernet transfers will not work correctly. PHY polling is enabled per default after reset, so we do not need to specifically enable it, but this makes it clearer. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
Add a missing occurrance of PHY_INTERFACE_MODE_RGMII_ID, which should be handled identical to PHY_INTERFACE_MODE_RGMII. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to the Marvell mvpp2 ethernet driver for the missing port 0. This code is mostly copied from the Marvell U-Boot version and was written by Stefan Chulski. Please note that only SFI support have been added, as this is the only interface that this code has been tested with. XAUI and RXAUI support might follow at a later stage. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to the Marvell mvpp2 ethernet driver. This code is mostly copied from the Marvell U-Boot version and was written by Stefan Chulski. Please note that only RGMII and SGMII support have been added, as these are the only interfaces that this code has been tested with. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
Read the "phy-speed" DT property to differentiate between 1 and 2.5GB SGMII operations. Please note that its unclear right now, if this DT property will be accepted in mainline Linux. If not, we need to revisit this code and change it to use the accepted property. Signed-off-by: NStefan Roese <sr@denx.de> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
This patch does a bit of restructuring of the probe / init functions, mainly to allow earlier register access as it is needed for the upcoming GoP (Group of Ports) and NetC (Net Complex) code. Signed-off-by: NStefan Roese <sr@denx.de> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
This patch adds the new PHY interface modes XAUI, RXAUI and SFI that will be used by the PPv2.2 support in the Marvell mvpp2 ethernet driver. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Stefan Roese 提交于
This patch adds the PPv2.2 specific FIFO configuration to the mvpp2 driver. The RX FIFO packet data size is changed to the recommended FIFO sizes. The TX FIFO configuration is newly added. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Stefan Chulski <stefanc@marvell.com> Cc: Kostya Porotchkin <kostap@marvell.com> Cc: Nadav Haklai <nadavh@marvell.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-