- 15 2月, 2018 2 次提交
-
-
由 Faiz Abbas 提交于
Add CONFIG_DYNAMIC_CRC_TABLE to am335x_evm_defconfig to reduce the size of the image. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
-
由 Faiz Abbas 提交于
ISO and EFI partition configs in SPL are selected by default. However, they are not being used. Therefore, remove ISO and EFI partition support in SPL. Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 14 2月, 2018 10 次提交
-
-
由 Tom Rini 提交于
This driver is no longer used on any supported platform in U-Boot and there is no interest in maintaining it further from people that have used it historically. Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> c: Alexey Brodkin <alexey.brodkin@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Max Filippov 提交于
Remove CONFIG_BOOT_RETRY_TIME as it doesn't do much good and enable CONFIG_HUSH_PARSER in xtfpga_defconfig. Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
-
- 11 2月, 2018 2 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 10 2月, 2018 3 次提交
-
-
由 Vinitha Pillai-B57223 提交于
Enable validation of boot.scr script prior to its execution dependent on "secureboot" flag in environment. Enable fall back option to qspi boot in case of secure boot. Signed-off-by: NSumit Garg <sumit.garg@nxp.com> Signed-off-by: NVinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Rajat Srivastava 提交于
Currently in LS1088A, XIP mode in QSPI works up to 16 MB addresses. This patch enables QSPI support in XIP mode for addresses above 16 MB as well. Signed-off-by: NRajat Srivastava <rajat.srivastava@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Hou Zhiqiang 提交于
Enable PCIe and E1000 in ls1046aqds lpuart defconfig. Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 09 2月, 2018 3 次提交
-
-
由 Tom Rini 提交于
Migrate the base and sub-options to Kconfig. Note that we only enable this in the base sandbox config now. Cc: Alexey Brodkin <alexey.brodkin@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: NTom Rini <trini@konsulko.com> --- Is this driver still used anywhere? It's fishy that it's only enabled in sandbox anymore.
-
由 Adam Ford 提交于
config_fallbacks.h had some logic to automatically select LIB_RAND if RANDOM_UUID or CMD_UUID were set if LIB_HW_RAND wasn't already selected. By migrating LIB_HW_RAND to Kconfig, we can remove this check from config_fallbacks.h and put it into Kconfig Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NLukasz Majewski <lukma@denx.de> [trini: Turn into a choice, add NET_RANDOM_ETHADDR] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Michal Simek 提交于
Distro default configuration contains also dhcp and pxe setting which can't working without enabling CONFIG_NET. EFI is not required that's why it is not enabled. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 08 2月, 2018 6 次提交
-
-
由 Stefan Agner 提交于
This converts CONFIG_NAND_MXS to Kconfig. Signed-off-by: NStefan Agner <stefan.agner@toradex.com>
-
由 Stefan Agner 提交于
The motivation for moving MX28 selection to Kconfig is to be able to better handle NAND MXS selection through Kconfig. This selection method also aligns with the way other i.MX SoCs are selected in U-Boot. Signed-off-by: NStefan Agner <stefan.agner@toradex.com>
-
由 Stefan Agner 提交于
The motivation for moving MX23 selection to Kconfig is to be able to better handle NAND MXS selection through Kconfig. This selection method also aligns with the way other i.MX SoCs are selected in U-Boot. Signed-off-by: NStefan Agner <stefan.agner@toradex.com>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MXC_GPIO Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Adam Ford 提交于
Since CONFIG_PHY_SMSC was already in Kconfig, move this from header file to defconfig Signed-off-by: NAdam Ford <aford173@gmail.com>
-
由 Adam Ford 提交于
Since CONFIG_MXC_UART is already in Kconfig, move this from the header to imx6q_logic_defconfig Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NStefano Babic <sbabic@denx.de>
-
- 06 2月, 2018 2 次提交
-
-
由 Tuomas Tynkkynen 提交于
cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
由 Tuomas Tynkkynen 提交于
These are declared in Kconfig, but some #defines have crept in. CONFIG_FPGA CONFIG_FPGA_ALTERA CONFIG_FPGA_CYCLON2 CONFIG_FPGA_SOCFPGA CONFIG_FPGA_XILINX CONFIG_FPGA_ZYNQMPPL Signed-off-by: NTuomas Tynkkynen <tuomas@tuxera.com>
-
- 04 2月, 2018 11 次提交
-
-
由 Fabio Estevam 提交于
fastboot tool is a convenient way to flash the eMMC, so add support for it. Examples of usages: On the mx6sabresd: => fastboot 0 On the Linux PC connected via USB: $ sudo fastboot getvar bootloader-version -i 0x0525 bootloader-version: U-Boot 2018.01-00550-g7517cfe finished. total time: 0.000s $ sudo fastboot reboot -i 0x0525 (this causes the mx6sabresd to reboot) Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Tested-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Fabio Estevam 提交于
Select CONFIG_CMD_USB_MASS_STORAGE so that the 'ums' can be used. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Peng Fan 提交于
Enable UHS and HS200 for mx7dsabresd. Read Speed improvement: Kingston SD10VG2/16GB SDHC 3.0 card 22.2MB/s -> 73.7MB/s eMMC5.0 MTFC8GACAEAM: 68MB/s -> 87MB/s Signed-off-by: NPeng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
-
由 Eric Nelson 提交于
The initial implementation of mx6memcal reset the CPU after running the memory calibration procedure because the generic board has no information about which boot devices are available. Now that we have SDP support in SPL, use it to allow a full U-Boot to be uploaded (i.e. to use "mtest"). Signed-off-by: NEric Nelson <eric@nelint.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Eric Nelson 提交于
This patch just changes the order of configuration items in mx6memcal_defconfig to match the Kconfig layout, making it easier to track changes made using menuconfig. Signed-off-by: NEric Nelson <eric@nelint.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
-
由 Nandor Han 提交于
Validate the time at startup: - in case rtc error add to kernel command line RTC_ERROR - clamp date to 1-Jan-2036 Signed-off-by: NNandor Han <nandor.han@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
-
由 Ian Ray 提交于
Modify configuration to support FIT. Set variable `confidx' from VPD, in order to load the correct device tree. Modify/simplify U-Boot environment to support loading FIT image. Signed-off-by: NIan Ray <ian.ray@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
-
由 Ian Ray 提交于
Modify b450v3, b650v3 and b850v3 defconfigs to enable the network devices found in these products. Signed-off-by: NIan Ray <ian.ray@ge.com> Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
-
由 Jagan Teki 提交于
Enable nand on mmc defconfig, so-that preparing nand for writing/updating bootimage, Linux becomes easy. Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Jagan Teki 提交于
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for Android and video capture application. notable features: CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz Memory Up to 2 GB DDR3-1066 Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4 port 8 bit CSI INPUT MIPI-CSI INPUT 1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc This patch adds support for Quad/Dual and DualLite/Solo SOM's on MIPI starter kit with boot from SD and eMMC. Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Simon Glass 提交于
When functions return an error it propagates up the stack to the point where it is reported. Often the error code provides enough information about the root cause of the error that this is obvious what went wrong. However in some cases the error may be hard to trace. For example if a driver uses several devices to perform an operation, it may not be obvious which one failed. Add a log_ret() macro to help with this. This can be used to wrap any error-return value. The logging system will then output a log record when the original error is generated, making it easy to trace the call stack of the error. This macro can significantly impact code size, so its use is controlled by a Kconfig option, which is enabled for sandbox. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 02 2月, 2018 1 次提交
-
-
由 Lukasz Majewski 提交于
After moving some USB gadget configs (USB_FUNCTIONS_*) to Kconfig it turned out that following *_defconfig entries for RockChip are not needed. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-