- 18 2月, 2017 8 次提交
-
-
由 Tom Rini 提交于
This is no longer used anywhere. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Andrew F. Davis 提交于
When using early malloc the allocated memory can overflow into the SRAM scratch space, move NON_SECURE_SRAM_IMG_END down a bit to allow more dynamic allocation at the expense of a slightly smaller maximum image size. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 ahaslam@baylibre.com 提交于
The da850 soc's can boot from a external mmc card, but the AIS image should be written to the correct sector. Add instructions to copy the AIS image to a MMC card. Signed-off-by: NAxel Haslam <ahaslam@baylibre.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Semen Protsenko 提交于
serial# variable is used to correctly display device ID in "fastboot devices". It also can be used further for displaying device ID in "adb devices" (should be passed as "androidboot.serialno" to kernel cmdline, via "bootargs" variable). Serial number generating algorithm is described at [1]. [1] http://lists.denx.de/pipermail/u-boot/2015-March/207462.htmlSigned-off-by: NSam Protsenko <semen.protsenko@linaro.org> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Dalon Westergreen 提交于
Added SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION and SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION to Kconfig. Due to SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION being moved to Kconfig the board defconfigs for db-88f6820-gp_defconfig kc1_defconfig and sniper_defconfig need to be updated. Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
-
由 Dalon Westergreen 提交于
the socfpga bootrom supports mmc booting from either a raw image starting at 0x0, or from a partition of type 0xa2. This patch adds support for locating the boot image in the first type 0xa2 partition found. Assigned a partition number of -1 will cause a search for a partition of type CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE and use it to find the u-boot image Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
-
由 Andrew F. Davis 提交于
When the node 'reserved-memory' is not defined in the DT we fail to add needed properties. We also fail to move 'offs' to point to the new node. Fix these here. Signed-off-by: NAndrew F. Davis <afd@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
With gcc-6.x we see: drivers/i2c/fsl_i2c.c:86:3: warning: ‘fsl_i2c_speed_map’ defined but not used [-Wunused-const-variable=] The easy way to fix this is that since we only use fsl_i2c_speed_map at all on __M68K__ move the existing guards around slightly. Reported-by: NThomas Schaefer <Thomas.Schaefer@kontron.com> Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
- 17 2月, 2017 2 次提交
-
-
由 Chris Packham 提交于
Commit 94084eea ("tools: kwbimage: Fix dest addr") changed kwbimage to do this adjustment. So now the adjustment in kwboot is not needed (and would prevent UART booting for images generated by the new kwbimage). Remove the destaddr adjustment in kwboot. Signed-off-by: NChris Packham <judge.packham@gmail.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Mario Six 提交于
The return value of fstat was not checked in kwbimage, and in the case of an error, the already open file was not closed. Fix both errors. Reported-by: Coverity (CID: 155971) Reported-by: Coverity (CID: 155969) Signed-off-by: NMario Six <mario.six@gdsys.cc> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 14 2月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 2月, 2017 5 次提交
-
-
git://www.denx.de/git/u-boot-microblaze由 Tom Rini 提交于
Xilinx fixes for v2017.03 - defconfig alignment - Topic.nl board updates - Minor microblaze comment fix
-
由 Masahiro Yamada 提交于
With the Kconfig re-sync with Linux 4.10, characters such as '}', ';' in Kconfig help message cause warnings: $ make defconfig *** Default configuration is based on 'sandbox_defconfig' drivers/i2c/Kconfig:132:warning: ignoring unsupported character '}' drivers/i2c/Kconfig:132:warning: ignoring unsupported character ';' Drop the Device Tree fragment from the help. Acked-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Re-sync all files under the scripts/kconfig directory with Linux 4.10. Some parts include U-Boot own modification. I made sure to not revert the following commits: 5b8031cc ("Add more SPDX-License-Identifier tags") 192bc694 ("Fix GCC format-security errors and convert sprintfs.") da58dec8 ("Various Makefiles: Add SPDX-License-Identifier tags") 20c20826 ("Kconfig: Enable usage of escape char '\' in string values") Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The whole of common/flash.c is guarded by #if defined() ... #endif. Move the conditional to common/Makefile. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
- 11 2月, 2017 2 次提交
-
-
- 10 2月, 2017 17 次提交
-
-
由 Michal Simek 提交于
Use correct name in endif comment. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Mike Looijmans 提交于
The kernel partition in QSPI is 0x440000 large, not 0x400000. Fix this in the environment, otherwise the kernel will fail to boot if it occupies more space. Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Mike Looijmans 提交于
Allow sending firmware to RAM. Without this, the DFU support was not of much use. Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Mike Looijmans 提交于
On the miami board, ethernet is accessed via logic. To use it, one would have to program logic first and then set up the rgmii conversion block as well. Not likely to ever be used, so disable network support by default to save some space. Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Keep all defconfig sorted to ensure the smallest diff. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Simon Glass 提交于
We don't ever search for these so there is no need for a 4KB alignment. It just wastes space. Drop this and use the standard 4-byte alignment. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
-
由 Eddie Cai 提交于
Miniarm is the internal project code. Now it is officially named Tinker board. So rename it. Signed-off-by: NEddie Cai <eddie.cai@rock-chips.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Romain Perier 提交于
This commit enables ethernet MAC address randomization on the firefly-rk3288. It removes the error at startup 'ethernet@ff290000 address not set'. Signed-off-by: NRomain Perier <romain.perier@collabora.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Jacob Chen 提交于
Keep it same with other boards otherwise i have to write special script for it.. Signed-off-by: NJacob Chen <jacob2.chen@rock-chips.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Jacob Chen 提交于
To reduce redundant code. Signed-off-by: NJacob Chen <jacob2.chen@rock-chips.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This is wrong at present, so genboardscfg.py gives the following warnings: WARNING: no status info for 'chromebook_minnie' WARNING: no maintainers for 'chromebook_minnie' Fix it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Jacob Chen 提交于
miniarm board use lpddr3 Signed-off-by: NJacob Chen <jacob2.chen@rock-chips.com> Acked-by: NSimon Glass <sjg@chromium.org> Added 'rockchip:' prefix to subject: Signed-off-by: NSimon Glass <sjg@chromium.org> Change-Id: I84c3679dab2dbd8d01c1ebfd22220946d07c03cd
-
由 Tom Rini 提交于
It was incorrect to always include "asm/arch-omap3/mux.h" constantly. This introduced warnings on non-omap3 where certain values will conflict between the various families. Conditionally guard the inclusion in order to correct the problem. Fixes: 6aca17c9 ("drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xx") Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
-
由 Tom Rini 提交于
To save more space, switch to simple malloc here. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 2月, 2017 5 次提交
-
-
由 Tom Rini 提交于
The qemu-x86* targets do not want to enable this. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Fiach Antaw 提交于
MMC devices accessed exclusively via the driver model were not being initialized before being exposed as block devices, causing issues in scenarios where the MMC device is first accessed via the uclass block interface. Signed-off-by: NFiach Antaw <fiach.antaw@uqconnect.edu.au>
-
由 Adam Ford 提交于
On the OMAP36xx/37xx the CONTROL_WKUP_CTRL register has a field (bit 6) named GPIO_IO_PWRDNZ. If 0, the IO buffers which are related to GPIO_126, 127 and 129 are disabled. Some boards may need this for MMC. After the PBIAS is configured, this bit should be set high to enable these GPIO pins. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jaehoon Chung 提交于
ftsdc021_sdhci.c is dead file. There is no reason to maintain this host controller. Removes the entire ftsdc021_sdhci.c. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Jaehoon Chung 提交于
If there are alias nodes as "mmc", use the devnum as alias index number. This patch is for fixing a problem of Exynos4 series. Problem is the below thing. Current legacy mode: EXYNOS DWMMC: 0, SAMSUNG SDHCI: 1 After using DM: SAMSUNG SDHCI: 0, EXYNOS DWMMC: 1 Dev index is swapped. Then u-boot can't find the kernel image..because it is already set to 0 as mmcdev. If change from legacy to DM, also needs to touch all exynos4 config file. For using simply, just supporting the fixed devnum with alias node is better than it. Usage: alaise { .... mmc0 = &sdhci2; /* eMMC */ mmc1 = &sdhci1; /* SD */ ... } Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-