This patch add support for the Network Space v2 board and parents, based
on the Marvell Kirkwood 6281 SoC. This include Network Space (Max) v2
and Internet Space v2.

Additional information is available at:
http://lacie-nas.org/doku.php?id=network_space_v2Signed-off-by: NSimon Guinot <sguinot@lacie.com>

This adds support for the keymile Kirkwood BEC portl2 board. This board
relies on the km_arm (km_kirkwood) BEC.

The egiga driver is configured for a 100M full-duplex, A/N off connnection
to the backplane. This board has always ethernet present, because it is
connected to the marvell switch similar to mgcoge3un. The reset_phy
functionality is also the same to mgcoge3un.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>

suen3 and suen8 were in first HW version quite different, but
now they are from a u-boot point of view similar. So these
two boards can use the same header file. Other keymile boards
differ only in the usage of the PCI interface. Therefore
a target km_kirkwood_pci was introduced. All targets use
the same header file.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

I can't build test this, but just looking at the config files written
and it seems OK ...
Tested-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NScott McNutt <smcnutt@psyent.com>

Signed-off-by: NMichael Schwingen <michael@schwingen.org>

Signed-off-by: NMichael Schwingen <michael@schwingen.org>

Signed-off-by: NMichael Schwingen <michael@schwingen.org>

Make ATMEL's at91sam9260/9g20/9xe-ek boards build again
Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>

Minimal platform support to boot linux from SD.

Supported devices/hw limited to external MMC/SD slot,
GPIO, I2C and minimal PRCMU.
Signed-off-by: NJohn Rigby <john.rigby@linaro.org>
CC: Albert Aribaud <albert.aribaud@free.fr>

The mgcoge2un target was only an intermediate step to mgcoge3un.
For this reason the mgcoge2un support was moved to mgcoge3un,
because it isn't needed to support both targets.

We add the BootROM init file for the mgcoge3un memphis RAM.

We also move the suen3 and suen8 boards into the correct category
in the MAINTAINERS file.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>

config.mk should not be used in board directory and should be removed.
Use the same approach for building the image as other MX51/MX53 boards.

After this change vision2 board can be built again.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch
Signed-off-by: NJason Liu <jason.hui@linaro.org>

Signed-off-by: NShaohui Xie <b21989@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The otc570 board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

The meesc board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

Add support for Bluewater Systems AT91 based Snapper 9260 and 9G20
single board computer modules. Includes NAND flash and Ethernet
support.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>

- remove from boards.cfg
- add to doc/README.scrapyard
Signed-off-by: NEric Bénard <eric@eukrea.com>

Signed-off-by: NClint Adams <clint@debian.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Julian Pidancet <julian.pidancet@citrix.com>

Signed-off-by: NClint Adams <clint@debian.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Julian Pidancet <julian.pidancet@citrix.com>

This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>

The directory and file mgcoge was renamed to km82xx.
Because other keymile 82xx will follow and will use the
same platform code.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>

The Keymile SUPx5 board series is based on a PBEC8321 but
contains an additional PBUS FPGA (LPXF) on local bus CS2.
Signed-off-by: NThomas Reufer <thomas.reufer@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>

The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This board is similar to keymile suen3.
Signed-off-by: NClive Stubbings <clive.stubbings@xentech.co.uk>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount

This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NZhao Chenhui <b35336@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P3041DS & P5020DS boards are almost identical (except for the
processor in them).  Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.

Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS.  We utilize some of these for SERDES clock
configuration.

Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NShaohui Xie <b21989@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>

- fix board support following relocation changes
- switch to boards.cfg
- disable i2c to keep size under 128kiB (1 sector)
Signed-off-by: NEric Bénard <eric@eukrea.com>

- update to new relocation code
- switch to boards.cfg
- get rid of LEGACY (still a little hack in .h to compile)
- add nand boot configuration
- boot tested for the following configurations :
	9260 (64MB RAM & nor boot)
	9260_nand (64MB RAM & nand boot)
	9G20_128M (128MB RAM & nor boot)
	9G20_nand_128M (128MB RAM & nand boot)
	(nor boot is using lowlevel init)
Signed-off-by: NEric Bénard <eric@eukrea.com>

Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.

The board support is based on the BeagleBoard implementation.
Signed-off-by: NLuca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: NSrinath <srinath@mistralsolutions.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: NJason Liu <r64343@freescale.com>