Enable USB PHY driver.
Also fixed the alphabetically ordering of the config.
Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

Alias is required so req-seq will be filled.
Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

platdata_auto_alloc_size was not initialized in structure.
Caused null pointer dereference when configuring device as
gadget.
Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

Use standard board_usb_init() instead of the specific board_prepare_usb.
Signed-off-by: NRamon Fried <ramon.fried@gmail.com>

Since commit 7b3b74d3 ("serial: serial_stm32: Enable overrun")
on STM32F7xx based boards, the first lines of serial output are
missing during boot (we no more see the U-Boot release version,
board model and DRAM size).

By enabling the uart FIFO on STM32F7, the complete U-boot log
can be sent correctly.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>

Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Signed-off-by: NNeil Stainton <nstainton@asl-control.co.uk>
[trini: Manually apply, rework whitespace]
Signed-off-by: NTom Rini <trini@konsulko.com>

The escape sequence '\#' does not work for the latest GNU Make from
the git tree.

Replace it with $(pound) as Linux did.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

[ commit 9564a8cf422d7b58f6e857e3546d346fa970191e in Linux ]

I tried building using a freshly built Make (4.2.1-69-g8a731d1), but
already the objtool build broke with

orc_dump.c: In function ‘orc_dump’:
orc_dump.c:106:2: error: ‘elf_getshnum’ is deprecated [-Werror=deprecated-declarations]
  if (elf_getshdrnum(elf, &nr_sections)) {

Turns out that with that new Make, the backslash was not removed, so cpp
didn't see a #include directive, grep found nothing, and
-DLIBELF_USE_DEPRECATED was wrongly put in CFLAGS.

Now, that new Make behaviour is documented in their NEWS file:

  * WARNING: Backward-incompatibility!
    Number signs (#) appearing inside a macro reference or function invocation
    no longer introduce comments and should not be escaped with backslashes:
    thus a call such as:
      foo := $(shell echo '#')
    is legal.  Previously the number sign needed to be escaped, for example:
      foo := $(shell echo '\#')
    Now this latter will resolve to "\#".  If you want to write makefiles
    portable to both versions, assign the number sign to a variable:
      C := \#
      foo := $(shell echo '$C')
    This was claimed to be fixed in 3.81, but wasn't, for some reason.
    To detect this change search for 'nocomment' in the .FEATURES variable.

This also fixes up the two make-cmd instances to replace # with $(pound)
rather than with \#. There might very well be other places that need
similar fixup in preparation for whatever future Make release contains
the above change, but at least this builds an x86_64 defconfig with the
new make.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=197847
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

If we fail to find the MMC boot device, report the number of the one
we were looking for in the error to aid diagnosis.
Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com>

The Arm Versatile Express and Juno development boards contain an
OSC clock generator that can be accessed through the Versatile
Express config bus. The generators are quite often being controlled
by some MCU and the config bus offers a uniform way of exposing them.
Signed-off-by: NLiviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>

Fix failure to reimport exported checksummed, size constrained data block.

'env export -c' command ignores optional -s size argument when calculating checksum causing subsequent 'env import -c' to fail.
Signed-off-by: NNeil Stainton <nstainton@asl-control.co.uk>

Signed-off-by: NTom Rini <trini@konsulko.com>

Use device tree for mpc85xx with binman. Enabled for T2080QDS.

Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.

This converts the following to Kconfig:
   CONFIG_DISABLE_CONSOLE
Signed-off-by: NChristian Gmeiner <christian.gmeiner@gmail.com>

With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Signed-off-by: NAdam Ford <aford173@gmail.com>

With DM_MMC working for both SPL and U-Boot, this patch removes
the legacy style of initializing the MMC driver.
Signed-off-by: NAdam Ford <aford173@gmail.com>

With the pinctrl function enabled and the device tree setting up
the pins we want to use, this patch removes the manual pinmuxing
except for that which is not done by the device tree and minimal
pins necessary for SPL (like serial, GPMC, and MMC)
Signed-off-by: NAdam Ford <aford173@gmail.com>

With DM_I2C and DM_GPIO working, this patch can enable the
GPIO expander on the I2C bus.  This GPIO expander is connected
to some of the DIP switches and can now read the status of these
pins.
Signed-off-by: NAdam Ford <aford173@gmail.com>

The simple pin controller works for da850, so this patch enables
this to pin-mux the pins defined in the device tree for the da850evm.
Signed-off-by: NAdam Ford <aford173@gmail.com>

With DM enabled, this patch enables the 'dm' command to access
the dm tree, uclass and devres.
Signed-off-by: NAdam Ford <aford173@gmail.com>

The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Signed-off-by: NAdam Ford <aford173@gmail.com>

Previously poweroff was located under boot.  It seems to make more
sense to have it located under the Device access commands.
Signed-off-by: NAdam Ford <aford173@gmail.com>

With the omap_mmc driver no longer supporting cd-inverted, this
patch removes all these references since they are not needed.
Signed-off-by: NAdam Ford <aford173@gmail.com>

With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this.  This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: NTom Rini <trini@konsulko.com>

Add onewire node in device tree for TM series LCDs
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add onewire node in device tree for TM series LCDs
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add onewire node in device tree for TM series LCDs
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add onewire node in device tree for TM series LCDs
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add onewire node in device tree for TM series LCDs
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>