commit f31a911f (arm, post: add missing post_time_ms for arm)
enables get_ticks and get_tbclk for all arm based boards,
MX5/MX6 have not yet implemented.
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Liu <jason.hui@linaro.org>
CC: Marek Vasut <marek.vasut@gmail.com>

Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Helmut Raiger <helmut.raiger@hale.at>

commit f31a911f (arm, post: add missing post_time_ms for arm)
enables get_ticks and get_tbclk for all arm based boards,
MX5/MX6 have not yet implemented.
Signed-off-by: NStefano Babic <sbabic@denx.de>

This patch adds SPI support for the MX28EVK. Support for
an optionally installed SPI flash is also added. An example
configuration for redundant envrionment from SPI flash is also
added but disabled by default.

This patch has been tested on a MX28EVK Rev. D with an installed
SST25VF032B 32Mbit SPI flash.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: NFabio Estevam <fabio.estevam@freescale.com>

This patch enables USB host support on the MX28EVK board.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>

This patch adds support for the MX28 internal RTC
and enables u-boot's date command.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>

* 'master' of git://git.denx.de/u-boot-microblaze:
  microblaze: Enable TFTP put command
  microblaze: avoid interrupt race conditions
  microblaze: fix build failure due to undefined reference to `get_ticks'

Signed-off-by: NStephan Linz <linz@li-pro.net>

The interrupt acknowledge action have to run after the
registered interrupt handler. So we have a chance to
bear out the corresponding interrupt request in the
corresponding controller hardware.

With this reordering, we optain a proper interrupt
handling for level triggered interrupt sources -- for
example the new axi_timer v1.02.a introduced in ISE 13.2.
Signed-off-by: NStephan Linz <linz@li-pro.net>
Acked-by: NMichal Simek <monstr@monstr.eu>

after commit "common: add possibility for readline_into_buffer
timeout" (sha1:9c348311) was applied. The Microblaze generic build
fails with error below:

common/libcommon.o: In function `cread_line':
/devel/u-boot/common/main.c:717: undefined reference to `get_ticks'
/devel/u-boot/common/main.c:717: undefined reference to `get_tbclk'
/devel/u-boot/common/main.c:720: undefined reference to `get_ticks'
Signed-off-by: NStephan Linz <linz@li-pro.net>
Acked-by: NMichal Simek <monstr@monstr.eu>

This reverts commits 2faa7619 as
this has introduced some large problems on all other platforms and have
more changes in them than the commit message implies.

Cc: Heiko Schocher <hs@denx.de>
Cc: Patil, Rachna <rachna@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

This reverts commit 498cbdfe as we need
to revert the i2c changes that add the support for the platform.

Cc: Heiko Schocher <hs@denx.de>
Cc: Patil, Rachna <rachna@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>

* 'master' of git://git.denx.de/u-boot-mmc:
  mmc: make mmc_send_status() more reliable
  mmc: fix card busy polling
  Tegra: mmc: Fixed handling of interrupts in timeouts.
  omap_hsmmc: Wait for CMDI to be clear

* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/8xxx:Add MPH controller support in USB device-tree fixup
  powerpc/8xxx: Cleanup USB device-tree fixup

* 'trini@ti.com' of git://git.denx.de/u-boot-staging:
  usb_ether: fix typo
  cmd_eeprom: typo
  doc: complete, typos

* 'master' of git://git.denx.de/u-boot-x86:
  x86: Convert board_init_f_r to a processing loop
  x86: Split init functions out of board.c
  x86: Move relocation code out of board.c
  x86: Move setup_pcat_compatibility() out of board.c
  x86: Move do_go_exec() out of board.c
  CHECKPATCH: arch/x86/lib/*
  x86: Tweak IDT and GDT for alignment and readability
  x86: Allow cache before copy to RAM
  x86: Create weak init_cache() and default enable_caches() functions
  x86: Set GD_FLG_RELOC after entering in-RAM copy of U-Boot
  x86: Use fs for global data
  x86: Rework relocation calculations
  x86: Simplify Flash-to-RAM code execution transition
  x86: Rework Global Descriptor Table loading
  x86: Remove GDR related magic numbers
  x86: Speed up copy-to-RAM and clear BSS operations
  x86: Import glibc memcpy implementation

Align the card status polling with the Linux kernel and retry the
command at least five times. Also some cards apparently mishandle the
status bits, so make sure to check the card state too.
Signed-off-by: NJan Kloetzke <jan.kloetzke@dspg.com>
Cc: Andy Fleming <afleming@gmail.com>

A MMC/SD card may always go into the programming state (and hence be
busy) after a block write. Therefore always check the card state, even
after single block writes. On the other hand there is no need to check
the card status after a read.

Also make sure that errors during busy polling are propagated upwards.
Signed-off-by: NJan Kloetzke <jan.kloetzke@dspg.com>
Cc: Andy Fleming <afleming@gmail.com>

We are seeing occasional timeouts in the Tegra mmc code when
we are reading from external MMC cards. These don't seem to be
detrimental if they are handled properly.  This CL properly
clears the "normal interrupt status register" (norintsts) in
error conditions.  If we don't do this, when we come back into
mmc_send_cmd() the register will still contain status from the
last transaction.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Before we can send a command we need both the DATI (command inhibit on
mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear.
The previous behavior of only checking on DATI was insufficient on some
cards and incorrect behavior in any case.  This makes the code check
for both bits being clear and makes the error print more clear as
to what happened.  DATI_CMDDIS is removed as it was unused elsewhere
in the code and stood for 'DATI is set, cmds are disabled still'.

Fix originally spotted by Peter Bigot.
Tested-by: NPeter A. Bigot <bigotp@acm.org>
Tested-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NTom Rini <trini@ti.com>
Tested-by: NAndreas Müller <schnitzeltony@googlemail.com>

Add support for fixing usb mode and phy type for
MPH(Multi Port Host) USB controllers in device-tree nodes.
Required for socs like P3060, P5020, etc having MPH USB controller
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>

Some code cleanup done for USB device-tree fixup:
	- handling error value returned from fdt_fixup_usb_mode_phy_type()
	- using ARRAY_SIZE macro
	- using snprintf instead of sprintf
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>

Signed-off-by: NPeter Meerwald <p.meerwald@bct-electronic.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NPeter Meerwald <p.meerwald@bct-electronic.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>

mention repeatable to README.commands and fix some typos
Signed-off-by: NPeter Meerwald <p.meerwald@bct-electronic.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Tested-by: NMarek Vasut <marek.vasut@gmail.com>

* 'sf' of git://git.denx.de/u-boot-blackfin:
  README: Add description of SPI Flash (SF) command configuration
  sf command: allow default bus and chip selects
  sf: eeprom_m95xxx: set a sane default timeout
  sf: eeprom_m95xxx: fix up style

* 'master' of git://git.denx.de/u-boot-blackfin:
  Blackfin: pata_bfin: fix printf warning
  Blackfin: bfin_nand: mark local func static
  linkage.h: move from blackfin to common includes
  Blackfin: br4: new board port
  Blackfin: add in/out le32 variants
  post: add blackfin to the post_time_ms list
  Blackfin: bf537-stamp: drop board reset workaround
  Blackfin: pr1: new board port

Acked-by: NJason Liu <jason.hui@linaro.org>
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This patch allows a board configuration file to provide default bus
and chip-selects for SPI flash so that first argument to the 'sf' command
is optional.

On boards that use the mxc_spi driver and a GPIO for chip select, this allows
a much simpler command line:
	U-Boot> sf probe
instead of
	U-Boot> sf probe 0x5300
Tested-by: NJason Liu <jason.hui@linaro.org>
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Every board currently defines this to the same value, so just default
to that to avoid having to make everyone do the same thing.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

pata_bfin.c: In function 'bfin_ata_identify':
pata_bfin.c:887:2: warning: format '%x' expects type 'unsigned int',
	but argument 2 has type 'lbaint_t'
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This devready func is only used in this driver, so mark it static.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

1. Add linkage.h support from blackfin to common include,
   which is a reduced version from Linux.
2. Add architecture part support of linkage.h into blackfin
3. Fix include path of in blackfin related to linkage.h
   due to header file movement.
Signed-off-by: NMacpaul Lin <macpaul@andestech.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This adds support for the BR4 Appliance.  It is a quad channel ISDN BRI
board based on Blackfin BF537 CPU.
Signed-off-by: NDimitar Penev <dpn@switchfin.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

These are rarely used, but the post code does currently, so add small
redirect hacks for that.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The bf537-stamp shouldn't need this SPI flash workaround.  It was added
by accident a long time ago through a convoluted series of steps which
originated from a customer board (not the bf537-stamp).  So drop it to
keep people from incorrectly adding it to their own boards.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This add support for the PR1 Appliance - Asterisk based ISDN PRI PBX.
This board is Blackfin BF537 based.  The schematics are not fully opened.
Signed-off-by: NDimitar Penev <dpn@switchfin.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This patch adds support for the Calimain board from
OMICRON electronics GmbH. The board features a Texas Instruments AM1808
SoC, 128 MB DDR2 memory, and 64 MB NOR flash memory connected to CS2 and
CS3.
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>