- 22 11月, 2009 1 次提交
-
-
- 19 11月, 2009 6 次提交
-
-
由 Matthias Fuchs 提交于
This patch shrinks the PMC440 u-boot binary (from next branch) to fit into 384kB again. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
This is not the sequoia board. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
The latest changes in the u-boot/next branch increased the size of the alpr image a bit more. Now it doesn't fit into the 256k reserved for it. This patch now removes the commands "askenv" and "irq" which are not needed in the production systems. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
-
由 Stefan Roese 提交于
This patch removes the duplicted implementations of the pci_master_init() function by introducing a weak default function for it. It can be overridden by a board specific version. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch removes the duplicted implementations of the pci_pre_init() function by introducing a weak default function for it. This weak default has a different implementation for some PPC variants. It can be overridden by a board specific version. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch removes the duplicted implementations of the pci_target_init() function by introducing a weak default function for it. This weak default has a different implementation for 440EP(x)/GR(x) PPC's. It can be overridden by a board specific version (e.g. PMC440, korat). Signed-off-by: NStefan Roese <sr@denx.de> Acked-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
-
- 16 11月, 2009 5 次提交
-
-
由 Dirk Behme 提交于
Add support to use second and third I2C bus, too. Bus 0 is still the default, but by calling i2c_set_bus_num(1/2) before doing I2C accesses, code can switch to bus 1 and 2, too. Don't forget to switch back afterwards, then. Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Wolfgang Denk 提交于
-
-
-
-
- 14 11月, 2009 14 次提交
-
-
由 Amul Kumar Saha 提交于
Define and use CONFIG_ENV_ADDR_FLEX and CONFIG_ENV_SIZE_FLEX for storing environment variables. Signed-off-by: NRohit Hagargundgi <h.rohit@samsung.com> Signed-off-by: NAmul Kumar Saha <amul.saha@samsung.com>
-
由 Amul Kumar Saha 提交于
This patch adds support for Flex-OneNAND devices. Signed-off-by: NRohit Hagargundgi <h.rohit@samsung.com> Signed-off-by: NAmul Kumar Saha <amul.saha@samsung.com>
-
由 Mingkai Hu 提交于
The commit 66372fe2 manually relocated the bbt pattern pointer, which can be removed by using full relocation. Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
-
由 Mingkai Hu 提交于
Take advantage of the latest full relocation commit of PPC platform for boot from NAND. Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com> Acked-by: NKumar Gala <galak@kernel.crashing.org>
-
由 David Brownell 提交于
The syndrome based page read/write routines store ECC, and possibly other "OOB" data, right after each chunk of ECC'd data. With ECC chunk size of 512 bytes and a large page (2KiB) NAND, the layout is: data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines use a traditional layout -- data OOB, disregarding the prepad and postpad values -- so when they're used with that type of ECC hardware, those calls mix up the data and OOB. Which means, in particular, that bad block tables won't be found on startup, with data corruption and related chaos ensuing. The current syndrome-based drivers in mainline all seem to use one chunk per page; presumably they haven't noticed such bugs. Fix this, by adding read/write page_raw_syndrome() routines as siblings of the existing non-raw routines; "raw" just means to bypass the ECC computations, not change data and OOB layout. Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Sandeep Paulraj 提交于
When computing oobavail from the list of free areas in the OOB, don't assume there will always be an unused slot at the end. This syncs up with the kernel NAND driver. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
The patch updates the check condition for determining whether the ECC corrections has failed. This makes it similar to what is in the kernel NAND driver. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
Patch updates the comments and explanations for the arguments to various functions. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This was originally part of Thomas Gleixner's patch for adding support for 4KiB pages. This is not part of the U-Boot NAND driver so updating the driver with this to sync up with the kernel NAND driver. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
Patch removes already commented out dead code Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch updates the "chip_shift" calculation in the NAND driver. This is being done to sync up the NAND driver with the kernel NAND driver. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch adds support for NANDs greater than 2 GB. Patch is based on the MTD NAND driver in the kernel. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com> Signed-off-by: NScott Wood <scottwood@freescale.com>
-
由 Peter Tyser 提交于
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
由 Peter Tyser 提交于
Also remove vague, unnecessary comment Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
-
- 13 11月, 2009 3 次提交
-
-
由 Kumar Gala 提交于
We were incorrectly use the max CAM size as the number of entries in the array for setting up the addrmap. We should be using the NENTRY field which is the low 12-bits of TLB1CFG. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Mike Rapoport 提交于
Make smc911x_initialize return -1 on error and number of interfaces detected otherwise. Signed-off-by: NMike Rapoport <mike@compulab.co.il> Acked-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Mike Frysinger 提交于
When the smc911x driver was converted to NET_MULTI, the smc911x eeprom was missed. The config option needed updating as well as overhauling of the rergister read/write functions. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Tested-by: NMike Rapoport <mike.rapoport@gmail.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 12 11月, 2009 5 次提交
-
-
由 Dave Liu 提交于
commit 1542fbde introduced one new bug to chip-select interleaving. Single DDR controller also can do the chip-select interleaving if there is dual-rank or qual-rank DIMMs. Signed-off-by: NDave Liu <daveliu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
-
-
由 javier Martin 提交于
Sometimes, inside NetLoop, eth_halt() is called before eth_init() has been called. This is harmless except for free() calls to pointers which have not been allocated yet. This patch initializes those pointers to NULL and allocates them only the first time. This way we can get rid of free calls in halt callback. This has been tested in i.MX27 Litekit board and eldk-4.2 toolchains. Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 javier Martin 提交于
This patch fixes erroneous access to the ethernet PHY which broke the driver. 1. Selector field in the auto-negotiation register must be 0x00001 for using 802.3, not 0x00000 which is reseved. 2. Access to the PHY address specified by CONFIG_FEC_MXC_PHYADDR, not 0x0 fixed address. This has been tested in i.MX27 Litekit board and eldk-4.2 toolchains. Now using proper defines for auto-negotiation register. Signed-off-by: NJavier Martin <javier.martin@vista-silicon.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 11 11月, 2009 1 次提交
-
-
由 Ron Lee 提交于
------------------------------------------------------------------------ GCC 4.4 complains about this now. Signed-off-by: NRon Lee <ron@debian.org>
-
- 10 11月, 2009 5 次提交
-
-
由 Stefan Roese 提交于
This patch removes the Katmai "bootstrap" command and replaces it with the now common command "chip_config". Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
All currently available 4xx derivats have the I2C bootstrap EEPROM located on I2C bus number 0. This patch now first sets this bus number, so that the chip_config command also works for board with multiple I2C busses, like Katmai. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Matthias Fuchs 提交于
-add UBI support -increase malloc'able memory size -cleanup MONITOR|FLASH_BASE|LEN constants Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Ben Warren 提交于
Both lpd7a400 and lpd7a404 failed to compile because they had CONFIG_SMC_USE_IOFUNCS defined: examples/standalone/smc91111_eeprom.c:388: undefined reference to `SMC_outw' Also removed an orphaned paren in lpd7a404.h Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Ben Warren 提交于
This patch fixes the following warnings: Configuring for xaeniax board... smc91111_eeprom.c: In function 'print_macaddr': smc91111_eeprom.c:278: warning: suggest parentheses around + or - in operand of & smc91111_eeprom.c:281: warning: suggest parentheses around + or - in operand of & ... Configuring for xsengine board... smc91111_eeprom.c: In function 'print_macaddr': smc91111_eeprom.c:278: warning: suggest parentheses around + or - inside shift smc91111_eeprom.c:281: warning: suggest parentheses around + or - inside shift Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-