- 05 3月, 2015 1 次提交
-
-
由 Marek Vasut 提交于
Add support for USB host mode and USB device mode for the Cyclone V development kit and enable support for UMS (to export SD card as USB mass storage). The UMS is activated via 'ums 0 mmc 0' command, the system must be connected to a host PC via HPS USB port and SD card must be installed for this to work. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@opensource.altera.com> Acked-by: NDinh Nguyen <dinguyen@opensource.altera.com> Acked-by: NPavel Machek <pavel@denx.de> Reviewed-by: NStefan Roese <sr@denx.de> Cc: Vince Bridgers <vbridger@opensource.altera.com>
-
- 03 3月, 2015 1 次提交
-
-
由 Michal Simek 提交于
Add basic Xilinx ZynqMP arm64 support. Serial and SD is supported. It supports emulation platfrom ep108 and QEMU. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 02 3月, 2015 12 次提交
-
-
由 Andreas Bießmann 提交于
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Marcel Ziswiler 提交于
Integrate latest validated register settings from Toradex WinCE BSP 4.2 working accross all module versions from early V1.x, V1.2D, V2.2B to V2.4A. Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
Usually not required for NOR flash. Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
While 'mmc init' is no longer required the address to bootm the kernel from NOR flash was wrong. Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
Specify a CONFIG_BOARD_SIZE_LIMIT of 256 KB in order to avoid overwriting the factory configuration block located at offset 0x40000 in NOR flash. Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
To save more than 20 KB of precious space in NOR flash get rid of the following configuration options: CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_SYS_LONGHELP Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
Migrate Toradex Colibri PXA270 to use CONFIG_SYS_GENERIC_BOARD. Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Marcel Ziswiler 提交于
I couldn't quite figure out whether or not CONFIG_SYS_ENV_IS_NOWHERE actually ever worked but nowadays this is called CONFIG_ENV_IS_NOWHERE. Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
-
由 Marcel Ziswiler 提交于
Basically finish what the following commit started a long time ago: 488f5d87Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com> For mx35pdk/woodburn: Acked-by: NStefano Babic <sbabic@denx.de>
-
- 28 2月, 2015 2 次提交
-
-
由 Masahiro Yamada 提交于
PH1-Pro4 includes both EHCI and xHCI IP cores. Unfortunately, U-Boot cannot enable EHCI and xHCI support simultaneously. Some users may wish Super-Speed connection. Disable CONFIG_USB_EHCI_HCD and enable CONFIG_USB_XHCI_HCD. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Akshay Saraswat 提交于
This patch adds "iRAM, CPU state and low power" configs which are the addresses acting as flag registers. iROM code checks CONFIG_LOWPOWER_FLAG address. If it is equal to CONFIG_LOWPOWER_EN then it jumps to the address (0x02020000+CPUID*4). This is a part of iROM logic. Rest other flags are being used at various places during kernel switching and reset. They are nowhere documented because they are part programming. These configs are serving as flags for us because they are representing the addresses in iRAM which we are using for storing and extracting CPU Status and GIC status. Signed-off-by: NAkshay Saraswat <akshay.s@samsung.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 25 2月, 2015 24 次提交
-
-
由 Vladimir Barinov 提交于
This adds GPIO configuration and initialization function of SDHI on Silk board Signed-off-by: NVladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Vladimir Barinov 提交于
Porter is an entry level development board based on R-Car M2 SoC (R8A7791) This commit supports the following peripherals: - SCIF, I2C, Ethernet, QSPI, SD, USB Host Signed-off-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Lager board has two SDHI port as SDHI0 and SDHI2. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Gose board has three SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Koelsch board has three SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Alt board has two SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Silk board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Alt board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Lager board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Gose board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This adds drivers model support of serial port to Koelsch board, and migrate serial port to drivers model. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Fabio Estevam 提交于
Boards need to select CONFIG_SYS_GENERIC_BOARD in order to prevent removal from the project. Cc: Matthias Weisser <weisserm@arcor.de> Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Boards need to select CONFIG_SYS_GENERIC_BOARD in order to prevent removal from the project. Acked-by: NAnatolij Gustschin <agust@denx.de> Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Fabio Estevam 提交于
Boards need to select CONFIG_SYS_GENERIC_BOARD in order to prevent removal from the project. Acked-by: NAnatolij Gustschin <agust@denx.de> Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Masahiro Yamada 提交于
This is still a non-generic board. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: NSughosh Ganu <urwithsughosh@gmail.com> Cc: Syed Mohammed Khasim <sm.khasim@gmail.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Masahiro Yamada 提交于
This is still a non-generic board. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Chan-Taek Park <c-park@ti.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Masahiro Yamada 提交于
This is still a non-generic board. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Po-Yu Chuang <ratbert@faraday-tech.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Masahiro Yamada 提交于
These are still non-generic boards. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Greg Ungerer <greg.ungerer@opengear.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Masahiro Yamada 提交于
This is still a non-generic board. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Lei Wen <leiwen@marvell.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Masahiro Yamada 提交于
This is still a non-generic board. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Matthias Weisser <weisserm@arcor.de> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Enric Balletbo i Serra 提交于
Commit referenced in subject breaks IGEP0032 build with the following error: drivers/misc/status_led.c:30:7: error: 'RED_LED_GPIO' undeclared here (not in a function) scripts/Makefile.build:275: recipe for target 'drivers/misc/status_led.o' failed make[2]: *** [drivers/misc/status_led.o] Error 1 scripts/Makefile.build:420: recipe for target 'drivers/misc' failed make[1]: *** [drivers/misc] Error 2 Makefile:1093: recipe for target 'drivers' failed make: *** [drivers] Error 2 Fix this by skipping the status led on IGEP0032 machine as is not available and throw an error for future machines if the status led is not configured to avoid build breakage. Reported-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
-
由 Volodymyr Riazantsev 提交于
Add support of the DDR mode for eSDHC driver. Enable it for i.MX6 SoC family only. Signed-off-by: NVolodymyr Riazantsev <volodymyr.riazantsev@globallogic.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Minghuan Lian 提交于
The patch enables and adds PCIe settings for boards LS1021AQDS and LS1021ATWR. Signed-off-by: NMinghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 J. German Rivera 提交于
Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree from "fsl,dprcr" to "fsl-mc". Print MC version info when appropriate. Signed-off-by: NJ. German Rivera <German.Rivera@freescale.com> Signed-off-by: NLijun Pan <Lijun.Pan@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-