Signed-off-by: NBen Peled <bpeled@marvell.com>
Reviewed-by: NStefan Chulski <stefanc@marvell.com>
Reviewed-by: NKostya Porotchkin <kostap@marvell.com>
Signed-off-by: NStefan Roese <sr@denx.de>

GMII_SPEED should be enabled for 2.5G speed
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Reviewed-by: NYan Markman <ymarkman@marvell.com>
Reviewed-by: NKostya Porotchkin <kostap@marvell.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Because the mvpp2 driver now relies on the PHYLIB and
the external MDIO driver, configuring low level
SMI bus settings is redundant.
Signed-off-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NKostya Porotchkin <kostap@marvell.com>
Reviewed-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NStefan Roese <sr@denx.de>
Reviewed-by: NRamon Fried <rfried.dev@gmail.com>

Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NStefan Roese <sr@denx.de>
Reviewed-by: NRamon Fried <rfried.dev@gmail.com>

1. Differ between Port1 RGMII and SFI modes in Netcomplex config.
2. Remove XPCS config from SFI mode.
   Port1 doesn't XPCS domain, XPCS config should be removed.
   Access to Port1 XPCS can cause stall.
3. Add Port1 MPCS configurations.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Xilinx changes for v2021.07-rc3

ZynqMP:
- Syncup DT with Linux kernel
- Fix mmc mini configurations via DT
- Add pinctrl/psgtr description to DTs
- Add DTs for Kria boards
- Enable RTC and Time commands

Versal:
- Fix early BSS section location

Right now U-Boot is not aware about date/time that's why enable it by
default also with EFI runtime service for setting time.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

U-Boot expects to be linked to a specific hard-coded address and to
be loaded to and run from that address. CONFIG_POSITION_INDEPENDENT
config lifts that restriction & allowing the code to be loaded to
and executed from almost any address.

As we enabled CONFIG_POSITION_INDEPENDENT, CONFIG_INIT_SP_RELATIVE
is enabled by default, where it will set the early stack pointer at
runtime by adding an offset value to &_bss_start. The offset value
is taken from SYS_INIT_SP_BSS_OFFSET.

SYS_INIT_SP_BSS_OFFSET offset should be large enough so that the
early malloc region, global data (gd), and early stack should fit.
With commit d8fabcc424bd ("arm64: versal: Increase SYS_MALLOC_F_LEN")
SYS_MALLOC_F_LEN is increased from 32KB to 1MB, so we need to
accommodate this space with SYS_INIT_SP_BSS_OFFSET. Hence increasing
SYS_INIT_SP_BSS_OFFSET to 1.5MB.
Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The patch contains several DT files for SOM platform.
Carrier card is sck-kv (KV260) revA/B. SMK-K26 is description for starter
kit which doesn't have EMMC populated. And SM-K26 is full som with EMMC.

Files are divided in this way to make sure that SOM can be plugged to
different carrier card and all peripherals on SOM (or defined by a spec) can
be used by U-Boot. Full DT for SOM+CC can be merged together as overlays.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Mainline kernel has psgtr driver that's why it is good to add description
to DT files. Some boards are just missing description for USB3 and sata.
zc1751-dc1 and p-a2197 are also missing clock descriptions for input
clocks.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Probe zynqmp firmware driver by adding zynqmp firmware, power &
ipi mailbox device tree nodes for mini emmc.
Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com>

Add missing xlnx,mio-bank property to sdhci node. Also add properties with
0 value to have it listed in case that files are copied to different
projects where default case doesn't need to be handled in the same way.
That's why explicitly list them too.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

These comments weren't push to mainline that's why remove them.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

I2C muxes that have the slave devices with same address are
falling into the below problem.

VCK190 system controller (SC) - zynqmp-e-a2197-00-revA.dts
I2C1 (0xff030000) -> Mux1 (@0x74) -> Channel 3 -> 0x50
I2C1 (0xff030000) -> Mux2 (@0x75) -> Channel 0 -> 0x50

1. SC accesses I2C1 - Mux1 (0x74) - Channel 3 and then
2. SC accesses I2C1 - Mux2 (0x75) - Channel 0.

Now it results in 2 slave devices with same address (0x50)
on the I2C bus, making the communication un-reliable.

When ' i2c-mux-idle-disconnect' is in DT, after '1', the Mux
channel output is disconnected, making none of the channels
available to the I2C1. So, there is no question of having the
same addressed slave (0x50) present on the bus when we are doing '2'.

Same pattern is seen in below two boards also.

ZCU208 - zynqmp-zcu208-revA.dts
ZCU216 - zynqmp-zcu216-revA.dts
Signed-off-by: NRaviteja Narayanam <raviteja.narayanam@xilinx.com>

Add label to GPIO lines so the user-level applications can find any line
without knowing its physical path on System Controller on VCK190/VMK180.

These labels are describing EMIO gpio connection which depends on PL which
we normally don't describe but that's only way to go for now. Lately this
should be done out of this source code.
Signed-off-by: NSaeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The 'silabs,skip-recall' property prevents interruption in operation of
the clock while the driver is being probed.  Without this property, the
DDR DIMM clk can cause a failure during Versal's boot.
Signed-off-by: NSaeed Nowshadi <saeed.nowshadi@xilinx.com>

All si570 which are used for ps reference clock generation should contain
silabs,skip-recall property not to cause break on ps clock.
On Versal boards this will cause hang on Versal cpu when it is booted at
the same time with SC.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Pull request for efi-2021-07-rc3

Documentation:

* add a man-page for the size command
* add man-page for extension command to index

Bug fixes:

* avoid build failure due to missing SHA512 hardware acceleration
* correct error handling in TCG2 protocol
* don't let user disable capsule authentication
* correct reading directories via UEFI API

Build error occurs when CONFIG_EFI_SECURE_BOOT or
CONFIG_EFI_CAPSULE_AUTHENTICATE is enabled,
because hash-checksum.c is not compiled.

Since hash_calculate() implemented in hash-checksum.c can be
commonly used aside from FIT image signature verification,
this commit itroduces HASH_CALCULATE option to decide
if hash-checksum.c shall be compiled.
Signed-off-by: NMasahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

EFI_TCG2 depends not only on TPMv2 but also on the underlying algorithms.
So select the missing SHA1, SHA256, SHA384 and SHA512 we currently support
Reported-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>

Add 'default y'.
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Up to now we are stopping the EFI subsystem if a TPMv2 exists but the
protocol fails to install.  Now that we've switched the config to 'default
y' the sandbox TPM fails, since it doesn't support all the required
capabilities of the protocol.

Not installing the protocol is not catastrophic.  If the protocol fails
to install the PCRs will never be extended to the expected values, so
some other entity later in the boot flow will eventually figure it out
and take the necessary actions.

While at it fix a corner case were the user can see an invalid error
message when the protocol failed to install.  We do have a tcg2_uninit()
which we call when the protocol installation fails.  There are cases though
that this might be called before the configuration table is installed (e.g
probing the TPM for capabilities failed).  In that case the user will see
"Failed to delete final events config table".  So stop printing it since it's
not an actual failure , simply because the config table was never installed
in the first place.

In order to stop printing it make efi_init_event_log() and create_final_event()
cleanup themselves and only call tcg2_uninit() when the protocol installation
fails.
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Instead of just failing, clean up the installed config table and
EventLog memory if logging an s-crtm event fails during the protocol
installation
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>

Eliminate label 'out:' by using return.
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

efi_init_event_log() calls tcg2_uninit() in case of failure.
We can skip that since the function is called on efi_tcg2_register()
which also cleans up if an error occurs
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

This is same issue as https://bugzilla.redhat.com/show_bug.cgi?id=1733817,
but that fix was wrongly partial reverted.

When reading a directory, EFI_BUFFER_TOO_SMALL should be returned when
the supplied buffer is too small, so a use-case is to call
EFI_FILE_PROTOCOL.Read() with *buffer_size=0 and buffer=NULL to
obtain the needed size before doing the actual read.

So remove the check only for directory reading, file reading already
do the check by itself.

Fixes: db12f518("efi_loader: implement non-blocking file services")
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefan Sørensen <stefan.sorensen@spectralink.com>
Tested-by: NPeter Robinson <pbrobinson@gmail.com>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

The current capsule authentication code checks if the environment
variable capsule_authentication_enabled is set, for authenticating the
capsule. This is in addition to the check for the config symbol
CONFIG_EFI_CAPSULE_AUTHENTICATE. Remove the check for the environment
variable. The capsule will now be authenticated if the config symbol
is set.
Signed-off-by: NSughosh Ganu <sughosh.ganu@linaro.org>
Reviwed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Commit a479f103 ("hash: Allow for SHA512 hardware implementations")
defined function definitions for hardware accelerated SHA384 and SHA512.
If CONFIG_SHA_HW_ACCEL=y, these functions are used.

We already have boards using CONFIG_SHA_HW_ACCEL=y but none implements the
new functions hw_sha384() and hw_sha512().

For implementing the EFI TCG2 protocol we need SHA384 and SHA512. The
missing hardware acceleration functions lead to build errors on boards like
peach-pi_defconfig.

Introduce a new Kconfig symbol CONFIG_SHA512_HW_ACCEL to control if the
functions hw_sha384() and hw_sha512() shall be used to implement the SHA384
and SHA512 algorithms.

Fixes: a479f103 ("hash: Allow for SHA512 hardware implementations")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Building 32bit boards with the TCG2 protocol enabled leads to a build
warning due to a missing conversion.

    lib/efi_loader/efi_tcg2.c:774:27:
    error: cast to pointer from integer of different size
    [-Werror=int-to-pointer-cast]
    774 |  ret = tcg2_create_digest((u8 *)data_to_hash, data_to_hash_len,
        |                           ^
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>

'make htmldocs' results in a build warning

    checking consistency... doc/usage/extension.rst:
    WARNING: document isn't included in any toctree

Add the document to the index.

Fixes: 2f84e9cf ("cmd: add support for a new "extension" command")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Provide a man-page for the size command.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

My mail address doesn't work any longer, change to gmail.
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>

Versions of U-Boot before 2014.01 created a symlink from include/asm to
the architecture-specific header directory.

If an ARM board is build with that old version, then sandbox is built on
a more recent version (both with in-tree builds), the include/asm symlink
confuses the build system. It picks up the ARM headers when it should be
using the sandbox ones.

Since 2014 U-Boot has only created a symlink inside the include/asm/
directory and only for out-of-tree builds. So for in-tree builds it does
not expect to see an include/asm symlink. It is not removed by
'make mrproper'. It does show up with 'git status' but is easy enough to
miss.

Add include/asm to the files to remove with 'make mkproper'. For recent
U-Boot builds this has no effect, since include/asm is a directory, not a
file. If the include/asm symlink is there, it will be removed.
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>

s/psci_features/request_psci_features/g for the case when both
ARCH_SUPPORT_PSCI=y and ARM_PSCI_FW=y, that leads to these
compilation issues:

drivers/firmware/psci.c:69:12: error: conflicting types for 'psci_features'
   69 | static int psci_features(u32 psci_func_id)
      |            ^~~~~~~~~~~~~
In file included from drivers/firmware/psci.c:23:
./arch/arm/include/asm/system.h:548:5: note: previous declaration of 'psci_features' was here
  548 | s32 psci_features(u32 function_id, u32 psci_fid);
      |     ^~~~~~~~~~~~~
Tested-by: NAlexandru Gagniuc <mr.nuke.me@gmail.com>
Reported-by: NAlexandru Gagniuc <mr.nuke.me@gmail.com>
Fixes: b7135b03 ("psci: add features/reset2 support")
Signed-off-by: NIgor Opaniuk <igor.opaniuk@foundries.io>

This patch tries to distinguish two error messages.
Signed-off-by: Npeng.wang@smartm.com <peng.wang@smartm.com>

Python3 taken from the PATH causes build issues when pylibfdt bindings are
generated with Yocto SDK.

Python3 provided as a part of SDK is not compatible with host Python3,
therefore binding build breaks with following errors:

scripts/dtc/pylibfdt/libfdt_wrap.c:154:11: fatal error: Python.h: No such file or directory
  154 | # include <Python.h>
      |           ^~~~~~~~~~

Do not enforce the python3 from the PATH and make it conditionally-assigned
so it can be overridden from outside of build system. Keep the default
assignment to point to version that is taken from the PATH.

Similar fix has been introduced in b48bfc74 ("tools: allow to override
python"), where conditional assignment is used for python executable to
address similar build errors.
Signed-off-by: NAndrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Simon Glass <sjg@chromium.org>
Fixes: e91610da ("kconfig: re-sync with Linux 4.17-rc4")
Reviewed-by: NSimon Glass <sjg@chromium.org>

- Add base support for Marvell OcteonTX2 CN9130 DB (mostly done
  by Kostya)
- Sync Armada 8k MMU setup with Marvell version (misc Marvell
  authors)
- spi: kirkwood: Some fixes especially for baudrate generation
  (misc Marvell authors)
- mvebu: x530: Reduce SPL image size (Stefan)
- Rename "rx_training" to "mvebu_comphy_rx_training" (Stefan)

Currently all assembly optimized implementation of memory routines
show up at the top level of the RISC-V architecture Kconfig menu.
Let's group them together into a submenu.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>