ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.

More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.htmlSigned-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

The check of data became severe from newest gcc.
This patch checked in gcc-4.2 and 4.3 .
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

all sh boards use the same cpu linker script so move it to cpu/$(CPU)

that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk

tested on r2dplus
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

currently we need to sync the linker script enty and TEXT_BASE manualy
and the reloc_dst is based on it

instead provide it now from the ldflags

tested on r2dplus
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Conflicts:
	drivers/spi/Makefile
Signed-off-by: NWolfgang Denk <wd@denx.de>

This patch fixes a build problem noticed on Apollon by using
mtd_dev_by_eb() instead of "/" as done in the Linux UBI version.
So this brings the U-Boot UBI version more in sync with the Linux
version again.
Signed-off-by: NStefan Roese <sr@denx.de>

new chips supported:-
MX25L1605D, MX25L3205D, MX25L6405D, MX25L12855E
out of which MX25L6405D and MX25L12855E tested on Kirkwood platforms

Modified the Macronix flash support to use 2 bytes of device id instead of 1
This was required to support MX25L12855E
Signed-off-by: NPiyush Shah <spiyush@marvell.com>
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Looks like when I was encoding the sector sizes, I forgot to divide by 8
(due to the stupid marketing driven process that declares all sizes in
useless megabits and not megabytes).
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>

This patch abstracts Kirkwood arch specific changes to support ehci-kirkwood driver
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller.  Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>

There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>

This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>

The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).
Signed-off-by: NStefano Babic <sbabic@denx.de>

Due to change in the usb_board_init() prototype, the USB for
the TrizepsIV was not correctly initialized.
Removed dummy print from usb_board_stop().
Signed-off-by: NStefano Babic <sbabic@denx.de>

This patch looks okay on u-boot-net.git/next branch
but when it was merged to u-boot.git/master the last line is missing
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
Acked-by: NBen Warren <biggerbadderben@gmail.com>

This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

update against linux v2.6.30
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.

CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

Correct define typo (. -> ,)
Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Acked-by: NFabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NHeungJun, Kim <riverful.kim@samsung.com>
CC: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.

Without this patch, EMIF configurations made in board_init()
will be invalidated.
Signed-off-by: NThomas Lange <thomas@corelatus.se>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Peter Pearse <peter.pearse@arm.com>