Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.

Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865, and
some power rails. The board is mainly used to measure the power
consumption. As all those changes are done in at91bootstrap,
in U-Boot, only use another device tree file, no code needed
to change.

As there is additional power consumption when enbling the USB
Host and USB device, for the power consumption measurement
intention, disable the USB host and device.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>

Enable config options to support the SPL, increase the malloc
memory size for the SPL and board_init_f stage and increase
the memory space for the SPL binary.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>

Enable CONFIG_DM_ETH to make MACB to support driver model.

Because the USB Ether doesn't support driver model so far,
remove this feature.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>

Enable TI_COMMON_CMD_OPTIONS on all keystone2 platforms.
Also sync with savedefconfig.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable TI_COMMON_CMD_OPTIONS on all dra7xx platforms.
Also sync with savedefconfig.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable TI_COMMON_CMD_OPTIONS on all am57xx platforms.
Also sync with savedefconfig
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable TI_COMMON_CMD_OPTIONS on all am43xx platforms.
Also sync with savedefconfig.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable TI_COMMON_CMD_OPTIONS on all am335x platforms.
Also sync with savedefconfig.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
[trini: Re-sync, add in boneblack*, evm_hs_{norboot,spiboot,usbspl} configs]
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable I2C driver in ast2500 Eval Board defconfig.
Also enable i2c command.
Signed-off-by: NMaxim Sloyko <maxims@google.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Enable Pinctrl Driver in AST2500 Eval Board's defconfig
Signed-off-by: NMaxim Sloyko <maxims@google.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This change switches all existing users of ast2500 Watchdog to Driver
Model based Watchdog driver.

To perform system reset Sysreset Driver uses first Watchdog device found
via uclass_first_device call. Since the system is going to be reset
anyway it does not make much difference which watchdog is used.

Instead of using Watchdog to reset itself, SDRAM driver now uses Reset
driver to do that.

These were the only users of the old Watchdog API, so that API is
removed.

This all is done in one change to avoid having to maintain dual API for
watchdog in between.
Signed-off-by: NMaxim Sloyko <maxims@google.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This is a simple uclass for Watchdog Timers. It has four operations:
start, restart, reset, stop. Drivers must implement start, restart and
stop operations, while implementing reset is optional: It's default
implementation expires watchdog timer in one clock tick.
Signed-off-by: NMaxim Sloyko <maxims@google.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The IGEP SMARC AM335x is an industrial processor module with
following highlights:

  o AM3352 TI processor (Up to AM3359)
  o Cortex-A8 ARM CPU
  o SMARC form factor module
  o Up to 512 MB DDR3 SDRAM / 512 MB FLASH
  o WiFi a/b/g/n and Bluetooth v4.0 on-board
  o Ethernet 10/100/1000 Mbps and 10/100 Mbps controller on-board
  o JTAG debug connector available
  o Designed for industrial range purposes
Signed-off-by: NPau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Tested-by: NPau Pajuelo <ppajuel@gmail.com>

Convert IGEP board to use UBI volumes for U-Boot, its environment and
kernel. With exception of first four sectors read by SoC BootROM whole
NAND is UBI managed.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
Tested-by: NPau Pajuelo <ppajuel@gmail.com>

Rename igep0033 to igep003x as IGEP SMARC AM335x module (igep0034)
can use the same source files.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Tested-by: NPau Pajuelo <ppajuel@gmail.com>

With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.

Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
Signed-off-by: NVikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NVikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>

Add CONFIG_CMD_USB to the defconfig file.
Signed-off-by: NUri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: NTom Rini <trini@konsulko.com>

Add CONFIG_USB_STORAGE to the defconfig file.
Signed-off-by: NUri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: NTom Rini <trini@konsulko.com>

Modify the determination of the base address of xHCI registers of DRA7XX
targets.
Before the commit: by the target.
After the commit: by the USB port index.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: NUri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: NMarek Vasut <marex@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NMarek Vasut <marex@denx.de>
Acked-by: NMarek Vasut <marex@denx.de>

Banana Pi M2 Plus is an Allwinner H3-based SBC by Sinovoip, which has
already mainline device tree file that have landed into U-Boot source
tree.

Add a defconfig file for it and add the MAINTAINERS items.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Reviewed-by: NJagan Teki <jagan@openedev.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Banana Pi M2 Ultra has a SATA port connected to the internal SATA
controller of R40 SoC. The controller's 1.2v VDD is connected to ELDO3
and the 2.5v VDD is connected to DLDO4.

Enable these regulators as well as the SATA support of Banana Pi M2
Ultra, by adding needed config lines into its defconfig.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NTom Rini <trini@konsulko.com>

With 3f66149d we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup.  On ARM however we largely relied on this call.  Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location.  Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.

Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NStefan Roese <sr@denx.de>
Acked-by: NYork Sun <york.sun@nxp.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NChris Packham <judge.packham@gmail.com>
[trini: default y if DM_RTC, re-sync]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_DISPLAY
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_DIAG
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: imply CMD_DIAG on some keymile configs]
Signed-off-by: NTom Rini <trini@konsulko.com>

Rather than using CMD_CRAMFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CRAMFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: imply FS_CRAMFS for keymile]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_CRAMFS
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: imply CMD_CRAMFS for keymile]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_CLK
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: imply CMD_CLK on ARCH_ZYNQ]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_CHIP_CONFIG
Signed-off-by: NSimon Glass <sjg@chromium.org>

Rather than using CMD_CBFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CBFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: imply FS_CBFS on SYS_COREBOOT]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_CBFS
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: imply CMD_CBFS on SYS_COREBOOT]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_WHITE_ON_BLACK
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: Make this default y on various SoCs]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_BSP
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_BMP
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: Add depends on LCD || DM_VIDEO || VIDEO]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_BMODE
Signed-off-by: NSimon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_CMD_BEDBUG
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_BAT
Signed-off-by: NSimon Glass <sjg@chromium.org>