- 08 3月, 2010 1 次提交
-
-
由 Stefano Babic 提交于
The patch adds initial support for the Freescale mx51evk board. Network (FEC) and SD controller (fsl_esdhc) are supported. Signed-off-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NFred Fan <fanyefeng@gmail.com>
-
- 13 2月, 2010 3 次提交
-
-
由 Jens Scharsig 提交于
* new board (eb_cpux9k2) * support for EB+CPUx9K2 board by BuS Elektronik GmbH & Co. KG * select via make eb_cpux9k2_config * this also demonstrates, how to use boards with AT91RM9200 cpu in at91 arch tree Signed-off-by: NJens Scharsig <js_at_ng@scharsoft.de>
-
由 Matthias Kaehlcke 提交于
Added support for the following EDB93xx boards: EDB9301 EDB9302 EDB9302A EDB9307 EDB9307A EDB93012 EDB9315 EDB9315A Signed-off-by: NMatthias Kaehlcke <matthias@kaehlcke.net>
-
由 Daniel Gorsulowski 提交于
This patch adds support for esd gmbh OTC570 board. The OTC570 is based on an Atmel AT91SAM9263 SoC. Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
-
- 04 2月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
The EXBITGEN board has not been maintained for a long time; it has build problems, but no hardware is available any more for testing. Drop support for this board. Signed-off-by: NWolfgang Denk <wd@denx.de> Acked-by: NStefan Roese <sr@denx.de>
-
- 19 1月, 2010 1 次提交
-
-
由 Alessandro Rubini 提交于
Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
-
- 17 1月, 2010 3 次提交
-
-
由 Harald Krapfenbauer 提交于
Signed-off-by: NHarald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Michael Hennerich 提交于
The new board revision has a different LCD. Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Valentin Yakovenkov 提交于
Signed-off-by: NValentin Yakovenkov <yakovenkov@niistt.ru> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 08 1月, 2010 1 次提交
-
-
由 Reinhard Arlt 提交于
The caddy2 is a variant of the already supported vme8349. So we just add the differences to this board port. To better support those two boards we switched from fixed SDRAM configuration to usage of spd_sdram(). This is done by providing a board specific SPD EEPROM routine with different values for both boards. Signed-off-by: NReinhard Arlt <reinhard.arlt@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de> changed to use mkconfig -t option instead, plus misc codingstyle fixes. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 03 12月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Becky Bruce <beckyb@kernel.crashing.org>
-
- 28 11月, 2009 2 次提交
-
-
由 Po-Yu Chuang 提交于
This patch adds support for A320 evaluation board from Faraday. This board uses FA526 processor by default and has 512kB and 32MB NOR flash, 64M RAM. FA526 is an ARMv4 processor and uses the ARM920T source in this patch. Signed-off-by: NPo-Yu Chuang <ratbert@faraday-tech.com>
-
由 Sekhar Nori 提交于
Integrate DA830 EVM support into U-Boot. Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum Digital EVM board. See http://www.spectrumdigital.com/Signed-off-by: NNick Thompson <nick.thompson@gefanuc.com>
-
- 31 10月, 2009 1 次提交
-
-
由 Wolfgang Grandegger 提交于
This patch adds support for the board IPEK01 based on the MPC5200. The Futjitsu Lime graphics controller is configured in 16 bpp mode. Signed-off-by: NWolfgang Grandegger <wg@denx.de>
-
- 24 10月, 2009 1 次提交
-
-
由 Tom Rix 提交于
Start of support of Texas Instruments Software Development Platform(SDP) for OMAP3430 - SDP3430 Highlights of this platform are: Flash Memory devices: Sibley NOR, Micron 8bit NAND and OneNAND Connectivity: 3 UARTs and expanded 4 UART ports + IrDA Ethernet, USB Other peripherals: TWL5030 PMIC+Audio+Keypad VGA display Expansion ports: Memory devices plugin boards (PISMO) Connectivity board for GPS,WLAN etc. Completely configurable boot sequence and device mapping etc. Support default jumpering and: - UART1/ttyS0 console(legacy sdp3430 u-boot) - UART3/ttyS2 console (matching other boards, and SDP HW docs) - Ethernet - mmc0 - NOR boot Currently the UART1 is enabled by default. for compatibility with other OMAP3 u-boot platforms, enable the #define of CONSOLE_J9. Conflicts: Makefile Fixed the conflict with smdkc100_config by moving omap_sdp3430_config to it is alphabetically sorted location above zoom1. Signed-off-by: NDavid Brownell <david-b@pacbell.net> Signed-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 19 10月, 2009 3 次提交
-
-
由 Sandeep Paulraj 提交于
Adding entries to the MAINTAINERS directory for the DM355 and DM365 EVM. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch adds support for the leopard board which is based on the DM355 SOC. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch adds the initial support for DM6467 EVM. Other features like NET and NAND support will be added as follow up patches. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 14 10月, 2009 1 次提交
-
-
由 Minkyu Kang 提交于
Adds new board SMDKC100 that uses s5pc100 SoC Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Signed-off-by: NHeungJun, Kim <riverful.kim@samsung.com>
-
- 13 10月, 2009 3 次提交
-
-
由 Simon Kagstrom 提交于
The implementation is borrowed from the sheevaplug board and the Marvell 1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA. Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
-
由 Tom Rix 提交于
these boards are built around Atmel's AT91SAM9260/9G20 and have up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND and include a 10/100 Ethernet PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Tom Rix 提交于
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 14 9月, 2009 1 次提交
-
-
由 Michal Simek 提交于
Users should use microblaze-generic platform. This platform is longer not supported. Signed-off-by: NMichal Simek <monstr@monstr.eu>
-
- 11 9月, 2009 1 次提交
-
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 05 9月, 2009 1 次提交
-
-
由 Frederik Kriewitz 提交于
This patch adds support for the DevKit8000 board. Signed-off-by: NFrederik Kriewitz <frederik@kriewitz.eu>
-
- 02 9月, 2009 4 次提交
-
-
由 Harald Krapfenbauer 提交于
The CM-BF537U is similar to the CM-BF537E module, but enough to need its own board port. Signed-off-by: NHarald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Albin Tonnerre 提交于
The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by Calao Systems <http://www.calao-systems.com>. Their components are very similar to the AT91SAM9260EK board, so their configuration is based on the configuration of this board. There are however some differences: different clocks, no LCD, no ethernet. They also can use SPI EEPROM to store the environment. Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Albin Tonnerre 提交于
The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems <http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND flash, two USB host ports, and an USB device port. More informations can be found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936> Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>
-
由 Ilya Yanok 提交于
This patch adds support for i.MX27-LITEKIT development board from LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND flash, FEC ethernet controller integrated into i.MX27. Signed-off-by: NIlya Yanok <yanok@emcraft.com> Acked-by: NWolfgang Denk <wd@denx.de>
-
- 29 8月, 2009 1 次提交
-
-
由 Poonam Aggrwal 提交于
The code base adds P1 & P2 RDB platforms support. The folder and file names can cater to future SOCs of P1/P2 family. P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series. Tested following on P2020RDB: 1. eTSECs 2. DDR, NAND, NOR, I2C. Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 25 8月, 2009 1 次提交
-
-
由 Eric Millbrandt 提交于
Add support for the DEKA Research and Development galaxy5200 board The galaxy5200 is an Freescale mpc5200 based embedded industrial control board. Signed-off-by: NEric Millbrandt <emillbrandt@dekaresearch.com>
-
- 28 7月, 2009 2 次提交
-
-
由 Dirk Eibach 提交于
Board support for the Guntermann & Drunck CompactCenter and DevCon-Center. Based on the AMCC Canyonlands board support by Stefan Roese. Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Reinhard Arlt 提交于
This patch adds support for the esd VME8349 board equipped with the MPC8349. It's a VME PMC carrier board equipped with the Tundra TSI148 VME-bridge. Signed-off-by: NReinhard Arlt <reinhard.arlt@esd-electronics.com> Signed-off-by: NStefan Roese <sr@denx.de> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 24 7月, 2009 4 次提交
-
-
由 Matthias Fuchs 提交于
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Peter Tyser 提交于
The XPedite1000 is an X-ES product thus it can be put in board/xes along with other X-ES boards. Along with the move, the board was renamed to XPedite1000 from XPedite1K to fit X-ES's standard naming convention. Maintainership was also transfered to Peter Tyser. Signed-off-by: NPeter Tyser <ptyser@xes-inc.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Dirk Eibach 提交于
Board support for the Guntermann & Drunck DL-Vision. Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 23 7月, 2009 1 次提交
-
-
由 Prafulla Wadaskar 提交于
This is Marvell's 88F6281_A0 based reference design board This patch is tested for- 1. Boot from DRAM/NAND flash/NFS 2. File transfer using tftp and loadb 3. NAND flash read/write/erase Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 19 7月, 2009 2 次提交
-
-
由 Prafulla Wadaskar 提交于
This is Marvell's 88F6281_A0 based custom board developed for wireless access point product This patch is tested for- 1. Boot from DRAM/SPI flash/NFS 2. File transfer using tftp and loadb 3. SPI flash read/write/erase 4. Booting Linux kernel and RFS from SPI flash 5. Boot from USB supported Reviewed-by: NRonen Shitrit <rshitrit@marvell.com> Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-
由 Prafulla Wadaskar 提交于
Reference: http://plugcomputer.org/ http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support This patch is tested for- 1. Boot from DRAM/NAND flash 2. File transfer using tftp 3. NAND flash read/write/erase 4. Linux kernel and RFS Boot from NAND 5. Enabled USB PHY init for kernel need 6. Boot from USB supported Note: to boot Kirkwood kernel with USB support, you should add "usb start" in the boot sequence Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-