- 12 2月, 2008 2 次提交
-
-
由 Timur Tabi 提交于
Remove the "#undef DEBUG" line from all Freescale 83xx board header files. The inclusion of this line makes it impossible to enable debug code in other source files, because "#define DEBUG" typically needs to be defined before any header files are included. Signed-off-by: NTimur Tabi <timur@freescale.com>
-
由 Kumar Gala 提交于
Move the flat device tree setup for QE related devices into a common file shared between 83xx & 85xx platforms that have QE's. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 07 2月, 2008 5 次提交
-
-
由 Grzegorz Bernacki 提交于
Signed-off-by: NJohn Rigby <jrigby@freescale.com> Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com>
-
由 John Rigby 提交于
Changes to match 5121 device tree going mainline in 2.6.25. Change OF_SOC from "soc5121" to plain "soc". Remove unneeded "ref-frequency" fixups. Remove "address" enetaddr fixup. Add bus-frequency fixup for old OF_SOC so old kernels with old device trees will work with new u-boot with 66MHz IPS clock Signed-off-by: NJohn Rigby <jrigby@freescale.com>
-
由 John Rigby 提交于
Recommended frequency is 66MHz Change divider from 4 to 3. Signed-off-by: NJohn Rigby <jrigby@freescale.com>
-
missing migration from "Cleanup of some init functions" in c837dcb1Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Larry Johnson 提交于
Signed-off-by: NLarry Johnson <lrj@acm.org>
-
- 05 2月, 2008 8 次提交
-
-
allow to use a different server as set in serverip add CONFIG_TFTP_FILE_NAME_MAX_LEN to configure the file name length if not defined the max length will be at 128 Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Wolfgang Denk 提交于
According to the OMAP5912 Serial Interfaces Reference Guide (see http://focus.ti.com/lit/ug/spru760c/spru760c.pdf, page 150), the FIFO_EN enable bit in the FIFO Control Register (FCR) can only be changed when the baud clock is not running, i. e. when both DLL and DLH are set to 0. Thus make sure that DLL and DLH are 0 when writing the FCR. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Harald Welte 提交于
This patch adds NAND support to the S3C24x0 SoC code in u-boot Signed-off-by: NHarald Welte <laforge@openmoko.org>
-
由 Harald Welte 提交于
This patch adds support for CONFIG_SERIAL_MULTI on s3c24x0 CPU's Signed-off-by: NHarald Welte <laforge@openmoko.org>
-
由 Harald Welte 提交于
This patch allows us to use the 'gd' pointer (and thus environment and everything else associated with it) from interrupt context on arm920t. Signed-off-by: NHarald Welte <laforge@openmoko.org>
-
由 Harald Welte 提交于
This patch adds a IRQ demultiplexer callback to the arm920 cpu core code, plus a stub implementation of it for the S3C2410. The purpose is to allow arm920t implementations such as the s3c24x0 to implement interrupt handlers in u-boot without having to touch core arm920t code. Signed-off-by: NHarald Welte <laforge@openmoko.org>
-
由 Hebbar 提交于
Add ifdef to bdinfo command to display ethernet information only if CONFIG_CMD_NET is defined for arm modules. Signed-off-by: NK R Gururaja Hebbar <gururajakr@sanyo.co.in>
-
由 Hebbar 提交于
Adds I2C init func call to init sequence for ARM boards. This is present in ppc,blackfin and other processor init sequence. Signed-off-by: NK R Gururaja Hebbar <gururajakr@sanyo.co.in>
-
- 04 2月, 2008 5 次提交
-
-
由 Ladislav Michl 提交于
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
由 Ladislav Michl 提交于
Signed-off-by: NLadislav Michl <ladis@linux-mips.org> Remove nowhere used struct bd_info_ext, remove trailing whitespaces, fix indentation.
-
由 Ladislav Michl 提交于
Somewhere during development of U-Boot-1.1.3 CONFIG_BOOTBINFUNC was renamed into CONFIG_INIT_CRITICAL which was 04 Apr 2005 replaced with CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT. However CONFIG_SKIP_LOWLEVEL_INIT has oposite meaning to CONFIG_BOOTBINFUNC, so fix configuration to reflect this fact. I'm sending this patch 4th (!) time in hope it produces at least some reaction. Signed-off-by: NLadislav Michl <ladis@linux-mips.org> Fix at91rm9200dk base and environment address.
-
由 stefano babic 提交于
MMC support for X_Scale PXA is broken and does not work. Mainly, the mmc_init() function cannot recognize current SD/MMC cards. There were already some patches around the world but none of them was merged into the official u-boot tree. This patch makes order fixing this issue. Resubmit after code cleanup. Applied and tested on PXA 270 (TrizepsIV module). Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 stefano babic 提交于
Fix gcc4 issue. With some toolchain, a previous patch that fixes gcc4 issues generates wrong code. (Problem was reported with gcc-4.0.2-glibc-2.3.6/arm-softfloat-linux-gnu). This patch fixes the problem and solves the gcc-4 issues as the linux kernel does. Signed-off-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NDmitry Ivanov <ivadmitry@gmail.com>
-
- 25 1月, 2008 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 23 1月, 2008 15 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
-
-
-
-
- 19 1月, 2008 1 次提交
-
-
由 Dave Liu 提交于
The commit 04a9e118 cause the 83xx immap broken, so the DMA and PCI will be failed. The patch fix the struct spi8xxx and rm struct spi83xx. Signed-off-by: NDave Liu <daveliu@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 18 1月, 2008 3 次提交
-
-
-
由 Haavard Skinnemoen 提交于
Add support for the ATNGW100 Network Gateway reference design, including flash, ethernet and MMC support. Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-
由 Haavard Skinnemoen 提交于
I don't know why the relevant layers can't do this by itself, but this is what ppc does. Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-