- 15 11月, 2010 4 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
eepro100 driver does not have write_hwaddr function. However, eth stuff executes write_hwaddr function because eth_device structure has not been initialized. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Ben Warren <biggerbadderben@gmail.com>
-
由 Nobuhiro Iwamatsu 提交于
dc2114x driver does not have write_hwaddr function. However, eth stuff executes write_hwaddr function because eth_device structure has not been initialized. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Ben Warren <biggerbadderben@gmail.com>
-
由 Nobuhiro Iwamatsu 提交于
rtl8139 driver does not have write_hwaddr function. However, eth stuff executes write_hwaddr function because eth_device structure has not been initialized. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Ben Warren <biggerbadderben@gmail.com>
-
由 Nobuhiro Iwamatsu 提交于
rtl8169 does not have write_hwaddr function. However, eth stuff executes write_hwaddr function because eth_device structure has not been initialized. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Ben Warren <biggerbadderben@gmail.com>
-
- 13 11月, 2010 3 次提交
-
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
-
- 12 11月, 2010 7 次提交
-
-
由 Becky Bruce 提交于
The size of the other bank needed to be added to the br0 setting; this got dropped in the LBC cleanup. Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org> Tested-by: NWolfgang Denk <wd@denx.de> Acked-by: NWolfgang Denk <wd@denx.de> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Timur Tabi 提交于
Display the 64-byte Reset Configuration Word (RCW) during boot, so that there's no confusion as to what RCW U-boot is using. Reset Configuration Word (RCW): 00000000: 4a500000 00000000 18181818 00008888 00000010: 28402400 00002000 fe800000 01200000 00000020: 00000000 00000000 00000000 000b0000 00000030: 00000000 00000000 00000000 00000000 Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
We appear to have different refclk's on the different corenet DS boards so move the define out of the common header. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
CONFIG_SYS_TEXT_BASE setting is common across the 'corenet_ds' board family so move it out of P4080DS.h and into corenet_ds.h Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Priyanka Jain 提交于
SQW/INT pin in RTC can be used for generating square wave(by default) or as interrupt line. U-boot is registering this pin for interrupts. Configuring SQW/INT bit as interrupt line during board initialization to avoid spurious interrupts generated by square wave. Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Haiying Wang 提交于
Introduce a SPL specific CONFIG_SYS_TEXT_BASE_SPL define to be used by the linker. This has similiar semantics to CONFIG_SYS_TEXT_BASE however since SPL is a unqiue image we introduce a new variable to control its text base address. Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 11 11月, 2010 3 次提交
-
-
由 Haiying Wang 提交于
Use CONFIG_SYS_MONITOR_BASE instead of CONFIG_SYS_TEXT_BASE in early init code so we can share the same code with NAND or NOR boot and not have additional ifdefs in here. Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Haiying Wang 提交于
Fix u-boot-nand.lds and u-boot-nand_spl.lds according to: Author: Peter Tyser <ptyser@xes-inc.com> Date: Wed Sep 29 14:05:56 2010 -0500 commit fbe53f59 85xx: Use gc-sections to reduce image size Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 10 11月, 2010 2 次提交
-
-
由 Kumar Gala 提交于
When P2020DS DDR2 was merged it was merged incorrectly and propogated to boards.cfg. Fix this by moving DDR2 config to be associated with P2020DS and not P1_P2_RDB. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Reinhard Meyer 提交于
Supports most types that support Read-Id and the FM25H20. Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 30 10月, 2010 9 次提交
-
-
由 Stefano Babic 提交于
Signed-off-by: NStefano Babic <sbabic@denx.de>
-
git://git.denx.de/u-boot-marvell由 Wolfgang Denk 提交于
Conflicts: include/configs/km_arm.h Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
-
-
-
由 Wolfgang Denk 提交于
For ARM systems, before ELF relocation was introduced, CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the U-Boot image from whereever it was loaded to it's link address (CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation was performed at all, it was just a memcpy(). With ELF relocation, this does not work like that any more, and related boards need to be fixed anyway. So don't keep this relict any longer. Signed-off-by: NWolfgang Denk <wd@denx.de> Tested-by: NHeiko Schocher <hs@denx.de> Tested-by: NReinhard Meyer <u-boot@emk-elektronik.de>
-
由 Wolfgang Denk 提交于
When this define was introduced, the idea was to provide a soft migration path for ARM boards to get adapted to the new relocation support. However, other recent changes led to a different implementation (ELF relocation), where this no longer works. By now CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it actually hurts because it obfuscates the actual code by sprinkling it with lots of dead and non-working debris. So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC. Signed-off-by: NWolfgang Denk <wd@denx.de> Tested-by: NHeiko Schocher <hs@denx.de> Tested-by: NReinhard Meyer <u-boot@emk-elektronik.de>
-
由 Wolfgang Denk 提交于
By now, the majority of architectures have working relocation support, so the few remaining architectures have become exceptions. To make this more obvious, we make working relocation now the default case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC. Signed-off-by: NWolfgang Denk <wd@denx.de> Tested-by: NHeiko Schocher <hs@denx.de> Tested-by: NReinhard Meyer <u-boot@emk-elektronik.de>
-
- 28 10月, 2010 12 次提交
-
-
由 Tanmay Upadhyay 提交于
If start of any DRAM bank is greater than total DDR size, remaining DDR banks' start address & size were left un-initialized in dram_init function. This could break other functions who uses array 'gd->bd->bi_dram'. Kirkwood network driver is one example. This also stops Linux kernel from booting. v2 - Set start address also to 0. Without this Linux kernel couldn't boot up Signed-off-by: NTanmay Upadhyay <tanmay.upadhyay@einfochips.com>
-
由 Prafulla Wadaskar 提交于
After moving the definition of CONFIG_SYS_TEXT_BASE to the respective board config files, all Marvell kirkwood board have just a single and common entry in their config.mk files: KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg Replace the only reference to KWD_CONFIG in the top level Makefile by an equivalent setting, and remove all kirkwood config.mk files. Signed-off-by: Wolfgang Denk <wd at denx.de> Cc: Prafulla Wadaskar <prafulla at marvell.com> Cc: Siddarth Gore <gores at marvell.com> Cc: Simon Kagstrom <simon.kagstrom at netinsight.net> Cc: Heiko Schocher <hs at denx.de> Cc: Eric Cooper <ecc at cmu.edu> Acked-by: Wolfgang Denk <wd at denx.de> Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-
由 Gray Remlin 提交于
Current default options increase u-boot size to overlap the location of the environment in NAND, move environment higher up Signed-off-by: NGray Remlin <g_remlin@rocketmail.com>
-
由 Shawn Guo 提交于
This patch is to fix build breakage and support new relocation scheme for mx51evk. - Correct IRAM base address and add size definition The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than 0x1FFE8000 which is for older revision. - Include imx-regs.h in mx51evk.h Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be referred to. - Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE They are used to define init RAM layout. - Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been buried by Wolfgang's commit below 25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value Signed-off-by: NShawn Guo <shawn.gsc@gmail.com>
-
由 Shawn Guo 提交于
This patch is to consolidate default mx51evk env for two primary boot modes, mmcboot and netboot. It also cleans some unused env like netdev, uboot and redundant env like loadaddr since CONFIG_LOADADDR already defines it. Signed-off-by: NShawn Guo <shawn.gsc@gmail.com>
-
由 Shawn Guo 提交于
The mx51evk u-boot has an issue that system will get reset every 2 hours. MC13892 has an inside charge timer which expires in 120 minutes. If ICHRG and CHGAUTOB are not set properly, this timer expiration will get system power recycled. Since mx51evk has no Li-Ion battery on board, the patch sets ICHRG in externally powered mode and sets CHGAUTOB bit to avoid automatic charging, so that system will not get reset by this timer expiration. The patch also corrects the bit field definition of register 48 (Charger 0) per latest MC13892 Reference Manual. Signed-off-by: NShawn Guo <shawn.gsc@gmail.com>
-
由 Stefano Babic 提交于
The patch removes the warning: clock.c:291: warning: initialization from incompatible pointer type after constification of args[] Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 Matthias Weisser 提交于
This patch fixes the reset command on imx25. The watchdog registers are 16 bits in size and not 32. This patch also adds the service register codes as constants. Signed-off-by: NMatthias Weisser <weisserm@arcor.de>
-
由 Jason Liu 提交于
Remove u-boot.lds from mx5 and use the common u-boot.lds of cpu layer. This patch also fix the building errors: arch/arm/cpu/armv7/start.o: In function `_rel_dyn_start_ofs': arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_start' arch/arm/cpu/armv7/start.o: In function `_rel_dyn_end_ofs': arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_end' arch/arm/cpu/armv7/start.o: In function `_dynsym_start_ofs': arch/arm/cpu/armv7/start.S:283: undefined reference to `__dynsym_start' Signed-off-by: NJason Liu <r64343@freescale.com>
-
由 Stefano Babic 提交于
Recent patch changed TEXT_BASE to CONFIG_SYS_TEXT_BASE and vision2 board was not updated. Signed-off-by: NStefano Babic <sbabic@denx.de>
-
由 C Nauman 提交于
This patch adds generic support for the Samsung s3c2440 processor. Global s3c24x0 changes to struct members converting from upper case to lower case. Signed-off-by: NCraig Nauman <cnauman@diagraph.com> Cc: kevin.morfitt@fearnside-systems.co.uk Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Mike Frysinger 提交于
Now that the common code takes care of stripping away quotes and such from numeric options, we no longer need to do so ourselves. So drop the custom code we have in the Blackfin config.mk. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-