geam6ul> mtdparts

device nand0 <nand>, # parts = 6
0: spl                 0x00200000      0x00000000      0
1: uboot               0x00200000      0x00200000      0
2: env                 0x00100000      0x00400000      0
3: kernel              0x00400000      0x00500000      0
4: dtb                 0x00100000      0x00900000      0
5: rootfs              0x1f600000      0x00a00000      0

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Enable MTD device, partition and command support.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add NAND support for Engicam GEAM6UL board.

Boot Log:
--------
U-Boot SPL 2016.11-g537fa5f (Nov 28 2016 - 11:42:28)
Trying to boot from NAND
NAND : 256 MiB

U-Boot 2016.11-g537fa5f (Nov 28 2016 - 11:20:06 +0100)

CPU:   Freescale i.MX6UL rev1.1 69 MHz (running at 396 MHz)
CPU:   Automotive temperature grade (-40C to 125C) at 42C
Reset cause: WDOG
Model: Engicam GEAM6UL
DRAM:  128 MiB
NAND:  256 MiB
MMC:   FSL_SDHC: 0
* Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add I2C support for Engicam GEAM6UL module.

geam6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
geam6ul> i2c dev 0
Setting bus to 0
geam6ul> i2c dev
Current bus is 0
geam6ul> i2c speed 100000
Setting bus speed to 100000 Hz
geam6ul> i2c probe
Valid chip addresses: 2C
geam6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add I2C nodes for Engicam GEAM6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Boot Log:
--------
U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30)
Trying to boot from MMC1

U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 43C
Reset cause: POR
Model: Engicam GEAM6UL
DRAM:  128 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
geam6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add i.MX6UL dtsi support from Linux.

Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add I2C support for Engicam i.CoreM6 qdl board.

icorem6qdl> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl> i2c dev 2
Setting bus to 2
icorem6qdl> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl> i2c probe
Valid chip addresses: 2C
icorem6qdl> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NHeiko Schocher <hs@denx.de>

Some I2C bus devicetree nodes, doesn't require to have
gpio pinctrl so replace the dev_info to debug so the
print never comes on the console and for bus that uses
gpio pinctrl anyway have dev_err.

Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.

After:
------
U-Boot> i2c dev 1
Setting bus to 1

Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NHeiko Schocher <hs@denx.de>

Better to print the hex value for bus address instead of
decimal, for more readbility on bus addressing.

Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 35274752, no gpio pinctrl state.

After:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.

Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NHeiko Schocher <hs@denx.de>

Added kconfig for SYS_I2C_MXC driver.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add custom splashscreen, engicam.bmp support for
Engicam i.CoreM6 qdl board.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add IPUv3 framebuffer support for Engicam i.CoreM6 qdl board.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Added kconfig entry for CONFIG_VIDEO_IPV3 driver.

Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Use CONFIG_DM_ETH and remove board_eth_init code
from board files.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add FEC dts support for Engicam i.CoreM6 dql modules.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add .read_rom_hwaddr on dm eth_ops.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

- Remove exctra space
- Add space
- Add tab space
- Fix single line comments quotes
- Fix 'CHECK: Avoid CamelCase'
- Fix 'CHECK: Alignment should match open parenthesis'
- Fix 'WARNING: line over 80 characters'
- Re-arrage header include files

Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

This patch add driver model support for fec_mxc driver.

Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

fec_get_hwaddr never used eth_device argument, hence removed.

Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.

The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: NPatrick Bruenn <p.bruenn@beckhoff.com>

Add plugin support for mx6sllevk board.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add i.MX6SLL EVK board support.
1. Add imx6sll-evk device tree.
2. Enable SDHC/I2C/UART.
3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver.

Boot Log:
U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800)

CPU:   Freescale i.MX6SLL rev1.0 at 792MHz
CPU:   Commercial temperature grade (0C to 95C)Reset cause: POR
Model: Freescale i.MX6SLL EVK Board
Board: MX6SLL EVK
DRAM:  2 GiB
i2c bus 0 at 35258368, no gpio pinctrl state.
PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add i.MX6SLL device tree.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

There two iomuxc for i.MX6SLL. One is normal IOMUXC, the other
is for IOMUXC_SNVS.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Update lcdif regs for i.MX6SL/SLL
Signed-off-by: NYe.Li <ye.li@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add the i.MX6SLL support to OCOTP driver.

The i.MX6SLL reuses the i.MX6ULL fuse, bank 7 and bank8 have 4 words
each, and there is a hole between bank 5 and bank 6.
Signed-off-by: NYe Li <ye.li@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Correct loadaddr and text base for i.MX6SLL
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

add Kconfig entry for i.MX6SLL
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

If L2 cache configured as OCRAM, reset it.
Switch to use runtime check.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add clock support for i.MX6SLL.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

The LCDIF Pixel clock mux is not glitchless, so need
to gate before changing mux.

Also change enable_lcdif_clock prototype with a new input
parameter to indicate disable or enable.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add lcdif clock support for i.MX6SL.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

The mux for the lcd clock is not glitchless,
so need to first gate the clock before changing the mux.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

>From RM, per_periph2_clk_sel option3 is:
"derive clock from 198MHz clock (divided 392MHz PLL2 PFD)."

So fix it.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add iomux settings for i.MX6 SLL
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Signed-off-by: NYe.Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add i.MX6 SLL GPT timer support.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Update register address for i.MX6 SLL
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add i.MX6SLL pinmux header files
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

Add i.MX6SLL cpu type.
MXC_CPU_MX6D is not a real value in chip, so change it to 0x6A.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>