Ethernet packages with IEEE 802.1Q VLAN support may be up to 1522
bytes long. Increase the default size used to allocate packet
storage by 4 bytes. While at it, let git care about history and
rewrite the comment to represent the situation today only.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Reviewed-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

VLAN identifiers are 12-bit decimal numbers, not IP addresses.
Signed-off-by: NStefan Agner <stefan@agner.ch>
Reviewed-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Move CONFIG_SPL_TEXT_BASE down to 0x40200000 and set CONFIG_SPL_MAX_SIZE
to (SRAM_SCRATCH_SPACE_ADDR - CONFIG_SPL_TEXT_BASE), so that it's clear
what the limit is.

This will also help some compilers to fit all the code into the allocated
space.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>

mx6ul_evk does not come with a eMMC populated, so we should not
define CONFIG_SUPPORT_EMMC_BOOT as it causes SPL to not be able
to boot some brands of SD cards, such as SanDisk microSD HC - 8GB:

U-Boot SPL 2016.05-rc1-28384-g108f8418 (Apr 19 2016 - 11:19:11)
Trying to boot from MMC1
spl: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

When CONFIG_SUPPORT_EMMC_BOOT is defined spl_boot_mode() returns
MMCSD_MODE_EMMCBOOT, so remove this option to have a reliable boot
via SD card.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>

Since 770e68c0
BoneGreen is detected in board_late_init as board_name 'BBG1'
Signed-off-by: NMatwey V. Kornilov <matwey.kornilov@gmail.com>

Signed-off-by: NVagrant Cascadian <vagrant@debian.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

I'll switch my mails to my own server, so drop all gmail references.
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

We cannot change the long standing hard-coded offset for raw boot mode
for everyone to accommodate how Android expects things to be done here.

This reverts commit ef5ebe95.
Signed-off-by: NTom Rini <trini@konsulko.com>

While the OMAP3 has 64KiB of SRAM, per the TRM the download area is only
from 0x40200000 to 0x4020F000 and exceeding that will cause failure to
boot.  Further, we need to make sure that we don't run into
SRAM_SCRATCH_SPACE_ADDR as once SPL is running we will write values
there and would corrupt our running image.

Cc: Adam Ford <aford173@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

The patch:
"configs: Re-sync almost all of cmd/Kconfig"
(sha1: 78d1e1d0)
doesn't remove empty if-endif. This patch is fixing it.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The defconfig/config.h file were merged but were already out of sync
with mainline.  This brings them further into line now.

Cc: Richard Hu <richard.hu@technexion.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

This allows to drop annoying (char *) casts when setting the host
name of struct sdhci_host.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The memory node gets automatically generated by U-Boot
in arch_fixup_fdt(), before passing control to the kernel
using U-Boots representation of the dram banks.

However the upstream kernel uses the memory node to carve-out
regions of RAM for various purposes. To make this work without
changing arch_fixup_fdt() which will effect many platforms
we replicate the upstream memory node layout using the dram
banks.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

Import the upstream kernel dts into U-Boot. Currently
only serial is supported, but a lot more DT changes are
queued for v4.7.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

According to common eMMC partition table for Android boot (see
PARTS_DEFAULT definition in include/configs/dra7xx_evm.h), "bootloader"
partition (where u-boot.img is stored) starts at 256 KiB. Which is equal
to 512 sectors (as 1 MMC sector size is 512 bytes).

This patch fixes CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR constant so that
it points to correct address of "bootloader" partition and SPL is able to
read, parse and run u-boot.img correctly.

This change was originally done as part of patch [1] in omapzoom u-boot.
Without this patch, SPL fails to parse U-Boot header with next error:

    mkimage signature not found - ih_magic = 4814325a

While at it, also fix U-Boot partition size, which is 384 KiB (as stated in
include/configs/dra7xx_evm.h).

[1] http://omapzoom.org/?p=repo/u-boot.git;a=commit;h=742b82d0c0aa0ed8096c2225a00e9f350212efa9Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: NTom Rini <trini@konsulko.com>

A number of moveconfig.py runs have left a instances of multiple empty
lines in a row.  Correct this to a single empty line.
Signed-off-by: NTom Rini <trini@konsulko.com>

This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND.  Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: NTom Rini <trini@konsulko.com>

Now that CONFIG_USB_MUSB_HOST is part of Kconfig, migrate that over to
the defconfig files.
Signed-off-by: NTom Rini <trini@konsulko.com>

Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files.  Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.
Signed-off-by: NTom Rini <trini@konsulko.com>

On some platforms (e.g. x86), the return value of dev_get_addr() can't
be assigned to a pointer type variable directly. As there might be a
difference between the size of fdt_addr_t and the pointer type. On
x86 for example, "fdt_addr_t" is 64bit but "void *" only 32bit. So
assigning the register base directly in dev_get_addr() results in this
compilation warning:
  warning: cast to pointer from integer of different size

This patch introduces the new function dev_get_addr_ptr() that
returns a pointer to the 'reg' address that can be used by drivers
in this case.
Signed-off-by: NStefan Roese <sr@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Copy the kernel image double-word-wise rather than byte-wise.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The last 64 byte of each DDR channel of PH1-LD20 is periodically
used as a scratch area for the DDR PHY training.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

This is the first ARMv8 SoC from Socionext Inc.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

And also reformat defconfigs using "make savedefconfig" rule.
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

Description was borrowed from kernel dwc3 Kconfig.
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some
config headers. This is also probably fixes am335x_baltos board.
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
  - add next options to Kconfig selecting USB_GADGET_DUALSPEED:
    - USB_GADGET_ATMEL_USBA
    - USB_GADGET_DWC2_OTG
    - USB_DWC3
    - CI_UDC
  - make USB_MUSB_GADGET select USB_GADGET_DUALSPEED

While at it, make some related fixes:
  - remove DUALSPEED from configs that don't enable gadget support:
    - kwb.h
    - tseries.h
  - add missing USB_GADGET option to next configs:
    - novena_defconfig
    - pcm051_rev*_defconfig
    - xfi3_defconfig
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

The description was borrowed from kernel. Definitions were added to
defconfig files in a way that "make savedefconfig" generates exactly
the same file as used defconfig.

Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use
2 mA (as minimal allowed by Kconfig).
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>

Add support for Technexion's PICO-IMX6UL-EMMC board.

For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmcSigned-off-by: NRichard Hu <richard.hu@technexion.com>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>

Setup the LCD backlight brightness control pin to use PWM
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>

As of commit 69e173eb, CONFIG_OF_LIBFDT
needs to be selected in defconfig instead of board specific header file.
Hence enable CONFIG_OF_LIBFDT in defconfig.
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>

When there is no $fdtfile variable set, we still have a good chance
that on 32bit arm the fdtfile really is just called $soc-$board.dtb.

Enable the exports for $soc and $board in our distr defaults and make
use of them in the efi boot script.
Reported-by: NAndreas Faerber <afaerber@suse.de>
Reported-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>
Reviewed-by: NAndreas Färber <afaerber@suse.de>

The bootefi cmd today fetches its device tree pointer from either the
location appointed by "fdt addr" with a fallback to the U-Boot control
fdt.

This integration is unusual for U-Boot and diverges from the way we
usually handle parameters to boot commands. So let's pass the fdt
directly into the bootefi command instead and move the control fdt
logic into the distro boot script.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Reviewed-by: NAndreas Färber <afaerber@suse.de>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>

Some variables for the distro boot commands were missing, using some
custom name instead. Rename them.

Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NAndreas Färber <afaerber@suse.de>

NAND is not yet enabled on all Keystone2 platforms. So enabled
CMD_NAND in the respective defconfigs only if available.
Reported-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Not all Keystone2 devices has AEMIF NAND controller. So adding Kconfig
entry for CONFIG_TI_AEMIF and enabling it in respective defconfigs on
platforms with AEMIF controller.
Reported-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>