Rename TARGET_T102XQDS to TARGET_T1024QDS to match the name.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_PPC_T1023 with ARCH_T1023 in Kconfig and clean up
existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

The defconfig files are separated. Splitting targets in Kconfig simplifies
config options.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_PPC_B4420 with ARCH_B4420 in Kconfig and clean up
existing macros.

Replace CONFIG_PPC_B4860 with ARCH_B4860 in Kconfig and clean up
existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_B4420QDS to simplify Kconfig options.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_P5040 with ARCH_P5040 in Kconfig and clean up
existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Replace CONFIG_PPC_P5020 with ARCH_P5020 in Kconfig and clean up
existing macros.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_P2020RDB_PC instead of sharing with P1_P2_RDB_PC to
simplify Kconfig and config macros.

Remove macro CONFIG_P2020RDB.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_P1025RDB instead of sharing with P1_P2_RDB_PC to
simplify Kconfig and config macros.

Remove macro CONFIG_P1025RDB.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_P1024RDB instead of sharing with TARGET_P1_P2_RDB_PC to
simplify Kconfig and macros.

Remove macro CONFIG_P1024RDB.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_P1021RDB instead of sharing with TARGET_P1_P2_RDB_PC to
simplify Kconfig and macros.

Remove macro CONFIG_P1021RDB.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_P1020UTM instead of sharing with TARGET_P1_P2_RDB_PC
to simplify Kconfig and config macros.

Remove macro CONFIG_P1020UTM.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_P1020RDB_PD instead of sharing with P1_P2_RDB_PC
to simplify Kconfig and config macros.

Remove macro CONFIG_P1020RDB_PD.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_P1020RDB_PC instead of sharing with TARGET_P1_P2_RDB_PC
to simplify Kconfig and config macros.

Remove macro CONFIG_P1020RDB_PC.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use TARGET_P1020MBG instead of sharing with TARGET_P1_P2_RDB_PC to
simplify Kconfig and other macros.

Remove macro CONFIG_P1020MBG.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Remove CONFIG_P1010RDB_PA and CONFIG_P1010RDB_PB and split TARGET_P1010RDB
to TARGET_P1010RDB_PA and TARGET_P1010RDB_PB in Kconfig.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use CONFIG_TARGET_C29XPCIE instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Use CONFIG_TARGET_BSC9132QDS from Kconfig option, remove CONFIG_BSC9132QDS
macro.
Signed-off-by: NYork Sun <york.sun@nxp.com>

This macro CONFIG_BSC9131RDB is no longer needed.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
[trini: Fix sniper and kc1 migration]
Signed-off-by: NTom Rini <trini@konsulko.com>

The SinA33 comes with an optional 7" display. Enable it in the
configuration.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

The SinA33 has an 4GB Toshiba eMMC connected to the MMC2 controller.
Enable it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>

Enable zynq Nand flash controller driver for a zynq ZC770
XM011(dc2) board.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM,
32MB QSPI NOR flash and 256MB NAND flash.

The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC,
2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources
and a fan controller.

The "Florida" carrier boards add SD, USB, ethernet and other interfaces.
Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Enable this so that EFI applications (notably grub) can be run under U-Boot
on x86 platforms.

At present the 'hello world' EFI application is not supported for the
qemu-x86_efi_payload64 board. That board builds a payload consisting of a
64-bit header and a 32-bit U-Boot, which is incompatible with the way the
EFI loader builds its EFI application. The following error is obtained:

x86_64-linux-ld.bfd: i386 architecture of input file
   `lib/efi_loader/helloworld.o' is incompatible with i386:x86-64 output

This could be corrected with additional Makefile rules. For now, this
feature is disabled for that board.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
[agraf: drop hello kconfig bits]
Signed-off-by: NAlexander Graf <agraf@suse.de>

Defconfigs should remain the same except CONFIG_SYS_EXTRA_OPTIONS.
Drop NAND specific defconfig as flash type is runtime detected.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Reviewed-by: NJavier Martinez Canillas <javier@samsung.com>

As a single U-Boot binary can now run on various board modifications,
drop CONFIG_DISPLAY_BOARDINFO as it prints flash memory information
too early to give us chance to easily detect it. Also saves few bytes
as a bonus.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Reviewed-by: NJavier Martinez Canillas <javier@samsung.com>
Tested-by: NJavier Martinez Canillas <javier@samsung.com>

Enable the Ethernet device in DT, provide board-specific configuration,
and enable the driver in Kconfig.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Enable ROCKCHIP_SPL_BACK_TO_BROM and disable CONFIG_SPL_MMC_SUPPORT
to save memory in order to enable add source code for dram capacity
auto-detect.
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>

The Cubieboard4 is an A80 SoC based development board from Cubietech.

This board has a UART port, 4 USB host ports, a USB 3.0 OTG connector,
HDMI and VGA outputs, a micro SD slot, 8G eMMC flash, 2G DRAM, a WiFi/BT
combo chip, headphone and microphone jacks, IR receiver, and GPIO headers.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

The A80 Optimus Board was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.

This board has a UART port, a JTAG connector, 2 USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 16G eMMC flash,
2G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: update existing Merrii_A80_Optimus_defconfig
 instead of adding a new defconfig]
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: NAmit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Originally dram clock was set to 480MHz, but this behaves
unstable. To improve stability the clock is reduced to 384MHz
Signed-off-by: NStefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

This was turned off by accident, re-enble.
Signed-off-by: NTom Rini <trini@konsulko.com>

Enable an early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Move the config options from the include/configs/sama5d2_xplained.h
to configs/sama5d2_xplained_*_defconfig.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Introduce CONFIG_PCI_PNP in Kconfig and move over boards' defconfig
to use that.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
[trini: Re-generate configs and include/configs/ changes]
Signed-off-by: NTom Rini <trini@konsulko.com>

Add 'PCI' as a menu option and migrate all existing users.
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NStephen Warren <swarren@nvidia.com>

Add NAND support for Engicam i.CoreM6 qdl board.

Boot Log:
--------

U-Boot SPL 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43)
Trying to boot from NAND
NAND : 512 MiB

U-Boot 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43 +0530)

CPU:   Freescale i.MX6SOLO rev1.3 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 55C
Reset cause: WDOG
Model: Engicam i.CoreM6 DualLite/Solo Starter Kit
DRAM:  256 MiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
icorem6qdl>

Cc: Scott Wood <oss@buserror.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>