- 20 4月, 2014 2 次提交
-
-
由 Masahiro Yamada 提交于
Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com>
-
由 Masahiro Yamada 提交于
Commit 54e458de deleted qi_lb60 board support because of the incompatible license issue. There is no board with XBurst CPU. Signed-off-by: NMasahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-
- 08 4月, 2014 2 次提交
-
-
由 Nitin Garg 提交于
Full cache line writes to the same memory region from at least two processors might deadlock the processor. Exists on r1, r2, r3 revisions. Signed-off-by: NNitin Garg <nitin.garg@freescale.com> Acked-by: NFabio Estevam <fabio.estevam@freescale.com>
-
由 Nitin Garg 提交于
A short loop including a DMB instruction might cause a denial of service on another processor which executes a CP15 broadcast operation. Exists on r1, r2, r3, r4 revisions. Signed-off-by: NNitin Garg <nitin.garg@freescale.com> Acked-by: NDirk Behme <dirk.behme@de.bosch.com>
-
- 03 4月, 2014 1 次提交
-
-
由 Przemyslaw Marczak 提交于
Those commands basis on implementation of random UUID generator version 4 which is described in RFC4122. The same algorithm is used for generation both ids but string representation is different as below. char: 0 9 14 19 24 36 xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx UUID: be be be be be GUID: le le le be be Commands usage: - uuid [<varname>] - guid [<varname>] The result is saved in environment as a "varname" variable if argument is given, if not then it is printed. New config: - CONFIG_CMD_UUID Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: trini@ti.com
-
- 23 3月, 2014 1 次提交
-
-
由 Heiko Schocher 提交于
on nand flash using ubi, after the download of the new image into the flash, the "rest" of the nand sectors get erased while flushing the medium. With current u-boot version dfu-util may show: Starting download: [##################################################] finished! state(7) = dfuMANIFEST, status(0) = No error condition is present unable to read DFU status as get_status is not answered while erasing sectors, if erasing needs some time. So do the following changes to prevent this: - introduce dfuManifest state According to dfu specification ( http://www.usb.org/developers/devclass_docs/usbdfu10.pdf ) section 7: "the device enters the dfuMANIFEST-SYNC state and awaits the solicitation of the status report by the host. Upon receipt of the anticipated DFU_GETSTATUS, the device enters the dfuMANIFEST state, where it completes its reprogramming operations." - when stepping into dfuManifest state, sending a PollTimeout DFU_MANIFEST_POLL_TIMEOUT in ms, to the host, so the host (dfu-util) waits the PollTimeout before sending a get_status again. Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
-
- 22 3月, 2014 1 次提交
-
-
由 Marek Vasut 提交于
Add simple 'aes' command, which allows using the AES-128-CBC encryption and decryption functions from U-Boot command line. Signed-off-by: NMarek Vasut <marex@denx.de>
-
- 05 3月, 2014 1 次提交
-
-
由 York Sun 提交于
Add 64-bit data for memory commands, such as md, mw, mm, cmp. The new size ".q " is introduced. For 64-bit architecture, 64-bit data is enabled by default, by detecting compiler __LP64__. It is optional for other architectures. Signed-off-by: NYork Sun <yorksun@freescale.com>
-
- 27 2月, 2014 2 次提交
-
-
由 Tom Rini 提交于
When we tell the compiler to optimize for ARMv7 (and ARMv6 for that matter) it assumes a default of SCTRL.A being cleared and unaligned accesses being allowed and fast at the hardware level. We set this bit and must pass along -mno-unaligned-access so that the compiler will still breakdown accesses and not trigger a data abort. To better help understand the requirements of the project with respect to unaligned memory access, the Documentation/unaligned-memory-access.txt file has been added as doc/README.unaligned-memory-access.txt and is taken from the v3.14-rc1 tag of the kernel. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Mans Rullgard <mans@mansr.com> Signed-off-by: NTom Rini <trini@ti.com>
-
由 Albert ARIBAUD 提交于
Remove the last uses of symbol offsets in ARM U-Boot. Remove some needless uses of _TEXT_BASE. Remove all _TEXT_BASE definitions. Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net>
-
- 22 2月, 2014 3 次提交
-
-
由 York Sun 提交于
Freescale LayerScape SoCs support controller interleaving on 256 byte size. This interleaving is mandoratory. Signed-off-by: NYork Sun <yorksun@freescale.com>
-
由 York Sun 提交于
DDR base address has been the same from the view of core and DDR controllers. This has changed for Freescale ARM-based SoCs. Controllers setup DDR memory in a contiguous space and cores view it at separated locations. Signed-off-by: NYork Sun <yorksun@freescale.com>
-
由 York Sun 提交于
Initially it was believed the DDR controller on Freescale ARM would have big endian. But some platform will have little endian. Signed-off-by: NYork Sun <yorksun@freescale.com>
-
- 21 2月, 2014 1 次提交
-
-
由 Tom Rini 提交于
We have an unused FAT implementation in fs/fdos, remove. Signed-off-by: NTom Rini <trini@ti.com>
-
- 20 2月, 2014 1 次提交
-
-
由 Heiko Schocher 提交于
add support for bootcounter on an i2c device. And add a README for all bootcounter options. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 19 2月, 2014 2 次提交
-
-
由 Detlev Zundel 提交于
Signed-off-by: NDetlev Zundel <dzu@denx.de>
-
由 Stephen Warren 提交于
This enables generic filesystem commands such as load and ls, which automatically work with multiple filesystem types, without having to be told which is present, unlike e.g. ext2load, fatls. Signed-off-by: NStephen Warren <swarren@nvidia.com>
-
- 06 2月, 2014 1 次提交
-
-
由 Marek Vasut 提交于
The architecture is unmaintained and dead, remove it. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michael Schwingen <michael@schwingen.org> Cc: Tom Rini <trini@ti.com>
-
- 04 2月, 2014 2 次提交
-
-
由 Michal Simek 提交于
Command provides just dump subcommand for showing clock frequencies in a soc. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Prabhakar Kushwaha 提交于
IFC registers can be of type Little Endian or big Endian depending upon Freescale SoC. Here SoC defines the register type of IFC IP. So update acessor functions with common IFC acessor functions to take care both type of endianness. Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Acked-by: NYork Sun <yorksun@freescale.com>
-
- 22 1月, 2014 1 次提交
-
-
由 Prabhakar Kushwaha 提交于
Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG. Also add their details in README. Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 13 1月, 2014 1 次提交
-
-
This config will use for defining greater than single flash support. currently - DUAL_STACKED and DUAL_PARALLEL. Signed-off-by: NJagannadha Sutradharudu Teki <jaganna@xilinx.com>
-
- 03 1月, 2014 2 次提交
-
-
由 Priyanka Jain 提交于
Single-source clocking is new feature introduced in T1040. In this mode, a single differential clock is supplied to the DIFF_SYSCLK_P/N inputs to the processor, which in turn is used to supply clocks to the sysclock, ddrclock and usbclock. So, both ddrclock and syclock are driven by same differential sysclock in single-source clocking mode whereas in normal clocking mode, generally separate DDRCLK and SYSCLK pins provides reference clock for sysclock and ddrclock DDR_REFCLK_SEL rcw bit is used to determine DDR clock source -If DDR_REFCLK_SEL rcw bit is 0, then DDR PLLs are driven in normal clocking mode by DDR_Reference clock -If DDR_REFCLK_SEL rcw bit is 1, then DDR PLLs are driven in single source clocking mode by DIFF_SYSCLK Add code to determine ddrclock based on DDR_REFCLK_SEL rcw bit. Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com>
-
由 Prabhakar Kushwaha 提交于
CONFIG_SPL_NAND_MINIMAL should not be used as it was defined for temporary review purpose. So, use CONFIG_SPL_NAND_BOOT config. Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
-
- 13 12月, 2013 1 次提交
-
-
Given a multi-file image created through the mkimage's -d option: $ mkimage -A x86 -O linux -T multi -n x86 -d vmlinuz:initrd.img:System.map \ multi.img Image Name: x86 Created: Thu Jul 25 10:29:13 2013 Image Type: Intel x86 Linux Multi-File Image (gzip compressed) Data Size: 13722956 Bytes = 13401.32 kB = 13.09 MB Load Address: 00000000 Entry Point: 00000000 Contents: Image 0: 4040128 Bytes = 3945.44 kB = 3.85 MB Image 1: 7991719 Bytes = 7804.41 kB = 7.62 MB Image 2: 1691092 Bytes = 1651.46 kB = 1.61 MB It is possible to perform the innverse operation -- extracting any file from the image -- by using the dumpimage's -i option: $ dumpimage -i multi.img -p 2 System.map Although it's feasible to retrieve "data files" from image through scripting, the requirement to embed tools such 'dd', 'awk' and 'sed' for this sole purpose is cumbersome and unreliable -- once you must keep track of file sizes inside the image. Furthermore, extracting data files using "dumpimage" tool is faster than through scripting. Signed-off-by: NGuilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 06 12月, 2013 1 次提交
-
-
由 Naveen Krishna Ch 提交于
This patch adds the U_BOOT_I2C_ADAP_COMPLETE defines for channels on Exynos5420 and Exynos5250 and also adds support for init function for hsi2c channels Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
-
- 26 11月, 2013 2 次提交
-
-
由 York Sun 提交于
Make PowerPC specific code conditional so ARM SoCs can reuse this driver. Add DDR3 driver for ARM. Signed-off-by: NYork Sun <yorksun@freescale.com>
-
由 York Sun 提交于
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: NYork Sun <yorksun@freescale.com>
-
- 25 11月, 2013 2 次提交
-
-
由 Igor Grinberg 提交于
Some GPIO connected LEDs have inverted polarity. Introduce new config option: CONFIG_GPIO_LED_INVERTED_TABLE for the specifying the inverted GPIO LEDs list and add support for this in the gpio_led driver. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Tested-by: NIlya Ledvich <ilya@compulab.co.il>
-
由 Igor Grinberg 提交于
The CONFIG_GPIO_LED symbol does not have any documentation in the README file. Document the CONFIG_GPIO_LED symbol. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
-
- 13 11月, 2013 3 次提交
-
-
由 Heiko Schocher 提交于
- add zync i2c driver to new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Michal Simek <michal.simek@xilinx.com>
-
由 Heiko Schocher 提交于
- add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/Signed-off-by: NHeiko Schocher <hs@denx.de> Tested-by: NTom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: NIgor Grinberg <grinberg@compulab.co.il> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Nobuhiro Iwamatsu 提交于
This updates to new I2C framwwork on sh_i2c. And this also updates boards(kzm9g and ecovec) that using sh_i2c. Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 12 11月, 2013 2 次提交
-
-
由 Heiko Schocher 提交于
As http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast states: "Initialize devices only when they are needed within U-Boot" enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is enabled. Enable this in ti_am335x_common.h, so all boards in mainline should work as before. Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
-
由 Heiko Schocher 提交于
If no softreset save registers are found on the hardware "bootcount" is stored in the environment. To prevent a saveenv on all reboots, the environment variable "upgrade_available" is introduced. If "upgrade_available" is 0, "bootcount" is always 0 therefore no need to save the environment on u-boot boot, if "upgrade_available" is 1 "bootcount" is incremented in the environment and environment gets written on u-boot start. So the Userspace Applikation must set the "upgrade_available" and "bootcount" variable to 0 (for example with fw_setenv), if a boot was successfully. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 09 11月, 2013 1 次提交
-
-
由 Przemyslaw Marczak 提交于
This patch allows exiting from UMS mode to u-boot prompt by detaching usb cable or by pressing ctrl+c. Add new config: CONFIG_USB_CABLE_CHECK. If defined then board file should provide function: usb_cable_connected() (include/usb.h) that return 1 if cable is connected and 0 otherwise. Changes v2: - add a note to the README Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
-
- 08 11月, 2013 2 次提交
-
-
由 Igor Grinberg 提交于
There is no CONFIG_PCA953X_INFO symbol. U-Boot uses CONFIG_CMD_PCA953X_INFO instead, which is described in "Monitor Functions" section and thus no need to be repeated in the "GPIO Support" section. Remove the whole line. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
-
由 Andrew Ruder 提交于
env exists is a way to test (in hush) if an environment variable exists. A workaround existed using printenv but this new command doesn't require all the stdout/stderr redirection to prevent printing information to the screen. Example: $ set testexists 1 $ env exists testexists && echo "yes" yes $ env exists testexists || echo "no" $ set testexists $ env exists testexists && echo "yes" $ env exists testexists || echo "no" no $ Signed-off-by: NAndrew Ruder <andrew.ruder@elecsyscorp.com>
-
- 30 10月, 2013 1 次提交
-
-
由 Heiko Schocher 提交于
make CONSOLE_BG_COL/CONSOLE_FG_COL configurable through board config file. Clear video screen in video_init(). Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Anatolij Gustschin <agust@denx.de>
-
- 17 10月, 2013 1 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
-