- 04 11月, 2019 40 次提交
-
-
由 Igor Opaniuk 提交于
Extend GPMI Integrated ECC Control Register Description, include additional defines for enabling randomizer function and providing proper randomizer type. For additional details check i.MX7 APR, section 9.6.6.3 GPMI Integrated ECC Control Register Description (GPMI_ECCCTRLn) Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com> Tested-by: NMax Krummenacher <max.krummenacher@toradex.com> Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>
-
由 Tom Rini 提交于
We have once again reached a point where this board does not build in some cases with supported toolchains due to reaching a size constraint. To regain some space, disable support for Plan 9 / RTEMS images with the bootm command. Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NStefano Babic <sbabic@denx.de>
-
由 Oliver Graute 提交于
Add i.MX8QM ROM 7720a1 board support Boot log as below: U-Boot 2019.10-rc3-00004-gd073e0242f (Sep 20 2019 - 08:24:13 +0200) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Advantech iMX8QM Qseven series Board: ROM-7720-A1 4GB Build: SCFW 65afe5f6 Boot: SD2 DRAM: 4 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 Net: eth0: ethernet@5b040000Could not get PHY for FEC1: addr 1 , eth-1: ethernet@5b050000 Hit any key to stop autoboot: 0 Signed-off-by: NOliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com>
-
由 Peng Fan 提交于
Sync dts for i.MX8MM from Linux Kernel 5.4.0-rc1 Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Hannes Schmelzer 提交于
This commit adds support for the brppt2 board. The board is based on the i.mx6 dual-lite SoC. Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>
-
由 Anatolij Gustschin 提交于
Borrow ID reading code from Ye Li (NXP U-Boot, commit ID 5b443e3e2617) but drop imx-mkimage commit ID reading since we now use in tree mkimage. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
由 Ye Li 提交于
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ, so update the interface to add new argument. Signed-off-by: NYe Li <ye.li@nxp.com> [agust: fixed imx8m-power-domain build] Signed-off-by: NAnatolij Gustschin <agust@denx.de> Reviewed-by: NPatrick Wildt <patrick@blueri.se> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Add secure boot script, use ahab to verify image Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Add secure boot script, use ahab to verify image Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Add function and new command "auth_cntr" for secure boot support. When booting with life cycle set to OEM closed, we need to use this function to authenticate the OS container and load kernel & FDT from OS container to their destination. Also add image authentication call when loading container images. Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not set at default. Signed-off-by: NYe Li <ye.li@nxp.com> Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for DRAM and linux suspend voltage requirement. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
We are going to add i2c pmic support before dram could be used. So we need enable clk driver earlier, so use spl_early_init and move clock controller probe eariler to board_init_f. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Add CONFIG_SPL_DM_PMIC_BD71837 to make this driver could be used in SPL stage Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Drop DEBUG macro definition which is used for debug purpose. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Import usb pd bindings from Linux 5.4.0-rc1. This file will be included by imx8mm-evk.dts. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
It will be easy to separate SD/EMMC when booting in SPL stage, then no need to bother which device is BOOT_DEVICE_MMC1/2. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF, so we still use legacy mode to configure the clock. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
Improve the IRQ response latency by setting GIC root clock source to sys_pll2_200m from osc. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Peng Fan 提交于
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id. It returns a magic number 0xff0055aa. update get_cpu_rev to support it, and enable ocotp clock to access ocotp. Signed-off-by: NPeng Fan <peng.fan@nxp.com>
-
由 Sébastien Szymanski 提交于
Set gd->fb_base so it can be shown with bdinfo command. Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
由 Sébastien Szymanski 提交于
Migrate to DM_VIDEO, update the device tree and remove code that is no longer necessary. Reviewed-by: NPeng Fan <peng.fan@nxp.com> Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
-
由 Sébastien Szymanski 提交于
Migrate to DM_ETH and remove code that is no longer necessary. Reviewed-by: NPeng Fan <peng.fan@nxp.com> Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
-
由 Patrick Wildt 提交于
This updates the i.MX8MQ device trees and, necessarily, also the i.MX8MQ clock bindings. These are taken verbatim from from the Linux kernel version v5.4-rc2, which three small changes which were already part of the previous device tree: * Keep the PSCI reserved memory range * Keep the alias for ethernet, so that the MAC address can be set * Keep the modified #include for the IOMUXC pins Signed-off-by: NPatrick Wildt <patrick@blueri.se> Acked-by: NPeng Fan <peng.fan@nxp.com>
-
由 Lukasz Majewski 提交于
After this change the SPL size has been reduced from 38K to 34K. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit enabled support for fitImage on mccmon6 when we switch to DT/DTS (including falcon mode). Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit adds falcon boot support (by also copying args necessary for booting) to the SPL NOR memory driver. After this change it is possible to use the falcon boot in the same way as on NAND memories. The necessary configs (i.e. CONFIG_CMD_SPL_NOR_OFS) are now defined in Kconfig. Signed-off-by: NLukasz Majewski <lukma@denx.de> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Lukasz Majewski 提交于
The mccmon6 has been used a "mixed" approach between SPL and U-Boot proper sources. This commit decoupes SPL and u-boot proper, which allows clear distinction between those two code bases and facilitates conversion to DM/DTS on this particular board. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit converts mccmon6's u-boot proper (in a single commit to avoid build breaks) to use solely DM/DTS. The DTS description of the mccmon6 has been ported from Linux kernel (v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be) Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
The TPC70 is equipped with DS1307 RTC device. Add code to enable support for it. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Claudius Heine 提交于
In order for 'bmode emmc' to work, the eMMC needs to be initialized in the SPL. This change initializes the eMMC as BOOT_DEVICE_MMC1 (index=0). Signed-off-by: NClaudius Heine <ch@denx.de>
-
由 Claudius Heine 提交于
Signed-off-by: NClaudius Heine <ch@denx.de>
-
由 Claudius Heine 提交于
The board_boot_modes contained the wrong values for the emmc entry. The eMMC here is connected over a 8-bit bus. This change allows to use the 'bmode emmc' command to boot from emmc. Signed-off-by: NClaudius Heine <ch@denx.de>
-
由 Robert Hancock 提交于
The expire_now function was previously setting the watchdog timeout to minimum and waiting for the watchdog to expire. However, this watchdog also has bits to trigger immediate reset. Use those instead, like the Linux imx2_wdt driver does. Signed-off-by: NRobert Hancock <hancock@sedsystems.ca>
-
由 Robert Hancock 提交于
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the device tree to specify whether the board design should use the external reset instead of the internal reset. Use this boolean to determine which mode to use rather than using external reset unconditionally. For the legacy non-DM mode, the external reset is always used in order to maintain the previous behavior. Signed-off-by: NRobert Hancock <hancock@sedsystems.ca>
-
由 Igor Opaniuk 提交于
Add u-boot,dm-pre-reloc properties for uart pinmux configuration nodes, which enables UART as early as possible (before relocation). Without this we miss almost the half of output (U-boot version, CPU defails, Reset cause, DRAM details etc.). Fixes: cd69e8ef ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm") Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: NFabio Estevam <festevam@gmail.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>
-
由 Igor Opaniuk 提交于
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to keep original imx6ull-colibri.dts in sync with Linux. Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi + additionally fix checkpatch warnings. Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: NFabio Estevam <festevam@gmail.com> Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>
-
由 Marek Vasut 提交于
According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating Conditions, page 16, the VDDD should be set to 1.55V when the CPU is operating at 454MHz. This is the case in U-Boot, hence increase the VDDD voltage. This fixes instability when performing TFTP transfers. Increase the brownout threshold to 1.4V. The documentation recommends 1.45V setting for the brownout, however, this triggers failure during power block init, so keep the brownout slightly lower. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: NFabio Estevam <festevam@gmail.com>
-
由 Claudius Heine 提交于
Signed-off-by: NClaudius Heine <ch@denx.de>
-
由 Claudius Heine 提交于
imx6_is_bmode_from_gpr9 always returns false, because IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return. This moves the function body into imx6_src_get_boot_mode, since that is the only one using it and it is on the same abstraction level (accessing registers directly). Signed-off-by: NClaudius Heine <ch@denx.de>
-
由 Manivannan Sadhasivam 提交于
Add devicetree support for iMXQXP AI_ML board from Einfochips. Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Reviewed-by: NLukasz Majewski <lukma@denx.de>
-