Move this option to Kconfig and tidy up existing boards.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Before Linux boot DPL must be deployed to DPAA2 interface.
So update bootcmd env variable to make sure DPL deployment before
Linux boot.
Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Define mcinitcmd env variable to load Management complex during
u-boot boot sequence.
Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Increase default hugepage count to 256 from 16
Signed-off-by: NAshish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Valid for core A57
Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Freescale's management complex (MC) uses System DDR for internal usage.
Increase used System DDR size from 256MB to 512 MB.
Signed-off-by: NPratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

MC and debug server are not board-specific. Move reserving memory to SoC
file, using the new board_reserve_ram_top function. Reduce debug server
memory by 2MB to make room for secure memory.

In the system with MC and debug server, the top of u-boot memory
is not the end of memory. PRAM is not used for this reservation.
Signed-off-by: NYork Sun <yorksun@freescale.com>

Remove 115200 from "earlycon" to avoid loss of initial
log messages during linux kernel 4.1  bootup
Signed-off-by: NPratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

As the environment variables "serial#" and "ethaddr" need to be
overwriten by the users, CONFIG_ENV_OVERWRITE is defined to disable
the write protection. Anybody can change or delete these parameters.
Signed-off-by: NAlison Wang <alison.wang@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: NPratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
           Dropped #ifdef in cpu.h
           Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: NYork Sun <yorksun@freescale.com>

LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: NPratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: NYork Sun <yorksun@freescale.com>

Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>

There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: NMingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: NHou Zhiqiang <B48286@freescale.com>
Signed-off-by: NGong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

This will allow OF-based earlycon to be used once the appropriate
aliases are added to the device tree and kernel support is fixed.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

The driver assumed that I2C1 and I2C2 were always enabled,
and if they were not, then an asynchronous abort was (silently)
raised, to be caught much later on in the Linux kernel.

Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4
are.

To make the change binary-invariant, declare I2C1 and I2C2 in
every include/configs/ file which defines CONFIG_SYS_I2C_MXC.

Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and
CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed
(CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE)
config options.
Signed-off-by: NAlbert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>

Enable CONFIG_CMD_GREPENV to allow search in env variables
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

LS2085 targets supports following UART console
 LS2085AQDS	UART0
 LS2085ARDB	UART1
 LS2085ASim	UART0
 LS2085AEmu	UART0

So update the bootargs as per the default console present at the target
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Add option to set shell prompt string from menuconfig and migrate
boards globally.

The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
  entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
  CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
  right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
  CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
  files. This results in a streamlined default value across platforms, and
  includes the following files: spear-common, sunxi-common, mv-common,
  ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
  not updated in their respective defconfig files under the assumption that
  since they did not explicitly define a value, they're fine with whatever
  the default is.
- On the other hand, boards that relied on a value defined in some
  <boards>_common.h file such as woodburn_common, rpi-common,
  bur_am335x_common, ls2085a_common, siemens_am33x_common, and
  omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
  assigning a value for CONFIG_SYS_PROMPT.

Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: NTom Rini <trini@konsulko.com>

Linux itb image size has been increased from 30MB.

So updating kernel_size to 40MB in env variable.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Stream IDs on ls2085a devices are not hardwired and are
programmed by sw.  There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Load AIOP image from NOR flash into DDR so that the MC firmware
the MC fw can start it at boot time
Signed-off-by: NJ. German Rivera <German.Rivera@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Signed-off-by: Stuart Yoder <stuart.yoder at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

The agreed split of the top of memory is 256M for debug server and 256M
 for MC. This patch implements the split.

 In addition, the MC mem must be 512MB aligned, so the amount of memory
 to hide must be 512MB to achieve that alignment.
Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Increases the kernel size supported for LS2085A platforms:-
 - Update environment variables
 - Add ramdisk_size in bootargs env variable
 - Define  CONFIG_SYS_BOOTM_LEN to 64MB

Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Compatible field "fsl,20851a-pcie" is not correct.
So update it to "fsl,ls2085a-pcie"

Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: NTom Rini <trini@konsulko.com>

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a83 (commands: add more
command entries in Kconfig).
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>

This patch adds esdhc support for ls2085a.
Signed-off-by: NYangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: NYork Sun <yorksun@freescale.com>

This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: NScott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: NYork Sun <yorksun@freescale.com>

The LS2085AQDS is an evaluatoin platform that supports the LS2085A
family SoCs. This patch add basic support of the platform.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com>

Changed MC firmware loading to comply with the new MC boot architecture.
Flush D-cache hierarchy after loading MC images. Add environment
variables "mcboottimeout" for MC boot timeout in milliseconds,
"mcmemsize" for MC DRAM block size. Check MC boot status before calling
flib functions.
Signed-off-by: NJ. German Rivera <German.Rivera@freescale.com>
Signed-off-by: NYork Sun <yorksun@freescale.com>

Add support of SerDes framework for Layerscape Architecture.
    - Add support of 2 SerDes block
    - Add SerDes protocol parsing and detection
    - Create table of SerDes protocol supported by LS2085A
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NMinghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.
Signed-off-by: NYork Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>

ls2085a_common.h contains hard-coded information for NOR/NAND flash,
I2C, DDR, etc. These are platform specific. Move them out of common
header file and placed into respective board header files.

Move TEXTBASE to 1MB offset to fit NOR flash with up to 1MB sector
size.

Enable command auto complete. Update prompt symbol. Set fdt_high to
0xa0000000 because Linux requires that the fdt  be 8-byte aligned
and below 512 MiB. Besides ensuring compliance with the 512 MiB
limit, this avoids problems with the dtb being misaligned within
the FIT image.

Change the MC FW, MC DPL and Debug server NOR addresses in compliance
with the NOR flash layouts for 128MB flash.

Add PCIe macros. Enable "loadb" command. Disable debug server.
Enable workaround for erratum A008511.
Stop reset on panic for postmortem debugging.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: NMinghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: NYork Sun <yorksun@freescale.com>

Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.
Signed-off-by: NYork Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>

Increase malloc length for more than 2M.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:

MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: NBhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Tested-by: NHeiko Schocher <hs@denx.de>
Acked-by: NHeiko Schocher <hs@denx.de>

Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory
fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree
from "fsl,dprcr" to "fsl-mc". Print MC version info when
appropriate.
Signed-off-by: NJ. German Rivera <German.Rivera@freescale.com>
Signed-off-by: NLijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>