Add support for the ARM part of the mgcoge2, named suen3.
This board is based on the Marvell Kirkwood (88F6281) SoC.
As there come more board variants, common config options
are collected in include/configs/km_arm.h. Also, this board
use common code for all keymile boards, which is stored in
board/keymile/common/common.c
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NHeiko Schocher <hs@denx.de>

This is an i.MX25 base board with only NAND
so it uses nand_spl to boot.
Signed-off-by: NJohn Rigby <jcrigby@gmail.com>

Tune configuration, add support for (redundant) environment in NAND.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Acked-by: NWolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>

Use RMII for MX25
Add code to init gasket that enables RMII
Signed-off-by: NJohn Rigby <jcrigby@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>

general cleanup
move clock init to cpu_eth_init in cpu/arm926ejs/mx27/generic.c
make MX27 specific phy init conditional on CONFIG_MX27
replace call to imx_get_ahbclk with one to imx_get_fecclk
and define imx_get_fecclk in include/asm-arm/arch-mx27/clock.h
Signed-off-by: NJohn Rigby <jcrigby@gmail.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>

ARM926EJS core with MX31 peripherals.
Signed-off-by: NJohn Rigby <jcrigby@gmail.com>
Earlier Version Signed-off-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>

remove ifdef'd clock selection code from
serial_mxc.c and replace with call to imx_get_uartclk

Add definitions for imx_get_uartclk to imx31 and imx27
include files.

This makes it easier to add new imx platforms.
Signed-off-by: NJohn Rigby <jcrigby@gmail.com>

The patch adds initial support for the Freescale mx51evk board.
Network (FEC) and SD controller (fsl_esdhc) are supported.
Signed-off-by: NStefano Babic <sbabic@denx.de>
Signed-off-by: NFred Fan <fanyefeng@gmail.com>

The esdhc controller in the mx51 processor is quite
the same as the one in some powerpc processors
(MPC83xx, MPC85xx). This patches adapts the driver
to support the arm mx51.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Some Freescale's processors of different architecture
have the same peripheral (eSDHC controller in PowerPC
and i.MX51). This patch adds accessors for
the internal registers of the SOCs, as already
implemented in the PowerPC architecture.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Most controllers can check if there is a card in the slot.
However, they require pins that could be not available because
required by other functions and the detection of a card must
be performed in another way. This patch adds a weak function
that a board can implement to add its internal custom way
to check the presence of a MMC/SD card.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Most cards do not answer if some reserved bits
in the ocr are set. However, some controllers
can set bit 7 (reserved for low voltages), but
how to manage low voltages SD card is not yet
specified.
Signed-off-by: NStefano Babic <sbabic@denx.de>

The patch adds support for the Freescale mx51 processor.
Signed-off-by: NStefano Babic <sbabic@denx.de>
Signed-off-by: NFred Fan <fanyefeng@gmail.com>

The patch add header files to support the pin multiplexer
of the the Freescale i.MX51 processor.
Signed-off-by: NStefano Babic <sbabic@denx.de>
Signed-off-by: NFred Fan <fanyefeng@gmail.com>

The patch add header files to support the Freescale i.MX51
processor, setting definitions for internal registers.
Signed-off-by: NStefano Babic <sbabic@denx.de>
Signed-off-by: NFred Fan <fanyefeng@gmail.com>

The patch add initial support for the Freescale i.MX51 processor
(family arm cortex_a8).
Signed-off-by: NStefano Babic <sbabic@denx.de>
Signed-off-by: NFred Fan <fanyefeng@gmail.com>

edb93xx: Fix SDRAM initialization by issuing a precharge all command before
forcing the precharge and select mode register update mode before programming
the mode registers. Write to the SDRAM banks in order to force a precharge,
reading causes the edb93xx boards to hang
Signed-off-by: NMatthias Kaehlcke <matthias@kaehlcke.net>

Use AT91_GPBR 3 as a bootcount register.
The bootmagic and the bootcount shares AT91_GPBR 3.
Signed-off-by: NAnders Darander <ad@datarespons.se>

Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with

repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit aea187c46f7d03ce985e55eb1398d0776a15b928
Signed-off-by: NTom Rix <Tom.Rix@windriver.com>

ep93xx: Refactoring of the timer code, including the following changes

 * use a free running timer instead of a periodical one
 * use unsigned long long for total number of ticks
 * hold the timer state in a structure instead of separate variables
 * increment the timer counter instead of decrementing it
 * remove unused function udelay_masked()
 * remove unused function set_timer()
Signed-off-by: NMatthias Kaehlcke <matthias@kaehlcke.net>

ep93xx: Use unsigned long long for calculation of sys ticks in clk_to_systicks()
for proper handling of large intermediate values
Signed-off-by: NMatthias Kaehlcke <matthias@kaehlcke.net>

725233: PLD instructions executed with PLD data forwarding
enabled can result in a processor deadlock

This deadlock can happen when NEON load instructions are used together
with cache preload instructions (PLD). The problematic conditions
can be triggered in-the-wild by NEON optimized functions from pixman
library (http://cgit.freedesktop.org/pixman), which perform dynamic
adjustment of prefetch distance.

The workaround disables PLD data forwarding by setting PLD_FWD bit
in L2 Cache Auxiliary Control Register as recommended in ARM Cortex-A8
errata list.

The deadlock can only happen on r1pX revisions of Cortex-A8 (used in
OMAP34xx/OMAP35xx). Performance impact of the workaround is practically
non-existant.
Signed-off-by: NSiarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Configuration defines should be preceeded with CONFIG_SYS_. Renamed
some at91 specific defines to conform to this naming convention:

AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME
AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK
Signed-off-by: NAchim Ehrlich <aehrlich@taskit.de>

linking eeprom with libgeneric.a is not really needed and causes following
error:
../../lib_generic/libgeneric.a(string.o): In function `strcmp':
/home/ladis/src/u-boot-ti/lib_generic/string.c:152: multiple definition of `strcmp'
../../examples/standalone/libstubs.a(stubs.o):include/_exports.h:24: first defined here
make[1]: *** [eeprom.srec] Error 1

Fix undefined reference to memset generated by some versions of gcc
to zero out initialized structure on the stack:
eeprom.o: In function `eeprom':
board/voiceblue/eeprom.c:152: undefined reference to `memset'
make[1]: *** [eeprom] Error 1
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Reindent configuration header to limit line lenght to 80 characters by
removing obvious and sometimes misleading comments.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Limit line length to 80 characters mostly by removing obvious and sometimes
misleading comments. Fix indentation, too.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

The patch adds an entry for the DM365 EVM to MAKEALL
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Adds support for ethernet networking on the da830evm platform.

This platform uses an SoC EMAC interface and a 3 port ethernet
switch as a PHY with an RMII interface. The PHY also has a i2c
interface for configuring the switch functions.
Signed-off-by: NNick Thompson <nick.thompson@ge.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Recent kernels are using generic NAND and NOR drivers. Change
default mtdparts to reflect it.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Correct switching partitions after upgrade and make it more readable.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

linking eeprom with libgeneric.a is not really needed and causes following
error:
../../lib_generic/libgeneric.a(string.o): In function `strcmp':
lib_generic/string.c:152: multiple definition of `strcmp'
../../examples/standalone/libstubs.a(stubs.o):include/_exports.h:24: first defined here
Remove eeprom linker script as well and generate entry point object
(to start application by jumping on its beginning) on the fly.
Out-of-tree build tested as well.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Use shorter yet descriptive messages, replace printf() with
puts() where appropriate. This saves few bytes.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Defining partially initialized struct eth_device on stack means
gcc has to zero out it, and some gcc versions optimize this with
an implicit call to memset. Move definition to data section
to avoid that (it has also nice side effect that we need not
to pass it to helper functions anymore)
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

For platforms with flash below ram addresses, the current check to
activate monitor protection is wrong/insufficient. This patch fixes
CONFIG_MONITOR_IS_IN_RAM for these systems by adding a check for
this configuration.
Signed-off-by: NWolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: NStefan Roese <sr@denx.de>

CONFIG_MONITOR_IS_IN_RAM is broken for MCF532x. This patch fixes this
 by conditionally
- removing the vector table at the beginning of code
- not overwriting the vector base register
- removing the code to re-set the PLL, which effectively disables
  SDRAM access
Signed-off-by: NWolfgang Wegner <w.wegner@astro-kom.de>

This patch adds a board_reset function to allow boards to specify
their own custom reset sequence (e.g. resetting by timing out watchdog).
Tested only on MCF5271, can be expanded if needed.

Based on Mike Frysinger's suggestion on:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/70304

Signed-off-by: Richard Retanubun <RichardRetanubun at RuggedCom.com>