With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: NHeiko Schocher <hs@denx.de>

As documented in doc/I2C_Edge_Conditions, adding a
board specific deblocking mechanism via CFG_I2C_INIT_BOARD
for the mgcoge and mgsuvd board.

This code was originally written by Keymile in association
with Anatech and Atmel in 1998. The Code toggels the SCL
until the SCA line goes to HIGH (max. 16 times).
And after this, a start condition is sent.

This is another approach to deblock the I2C Bus. The
soft I2C driver actually sends 9 clocks with SDA High,
and then a stop at the end, to deblock the I2C Bus.

Maybe we should use the approach from Keymile as
the new standard?
Signed-off-by: NHeiko Schocher <hs@denx.de>

This patch adds the option for a boardspecific
I2C deblocking mechanism for the soft i2c driver.
Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:

soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'
Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

Signed-off-by: NHeiko Schocher <hs@denx.de>

If I2C Bus is blocked (see doc/I2C_Edge_Conditions),
it is not possible to get out of this, until the
complete Hardware gets a reset. This new commando
calls again i2c_init (and that calls i2c_init_board
if defined), which will deblock the I2C Bus.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NWolfgang Denk <wd@denx.de>

There are some more extensions, which are for both boards
and some more boards from this manufacturer will follow soon.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NWolfgang Denk <wd@denx.de>

This patch adds support for the National LM63 temperature
sensor with integrated fan control. It's used on the GDSys
Neo board (405EP) which will be submitted later.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Acked-by: NStefan Roese <sr@denx.de>

Now it's used at UBI module. Of course other modules can use it.
If you want to use it, please define CONFIG_RBTREE
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>

Added support for CONFIG_EFI_PARTITION to ext2 commands.
Signed-off-by: NRichard Retanubun <RichardRetanubun@RugggedCom.com>

The GUID (Globally Unique Identifier) Partition Table (GPT) is a part
of EFI. See http://en.wikipedia.org/wiki/GUID_Partition_Table

Based on linux/fs/partitions/efi.[ch]
Signed-off-by: NRichard Retanubun <RichardRetanubun@RugggedCom.com>

Now that the auto-update feature uses the 'firmware' type for updates, it is
useful to inspect the load address of such images.
Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>

The auto-update feature allows to automatically download software updates
from a TFTP server and store them in Flash memory during boot. Updates are
contained in a FIT file and protected with SHA-1 checksum.

More detailed description can be found in doc/README.update.
Signed-off-by: NRafal Czubak <rcz@semihalf.com>
Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>

The upcoming automatic update feature needs the ability to adjust an
address within Flash to the end of its respective sector. Factor out
this functionality to a new function flash_sect_roundb().
Signed-off-by: NRafal Czubak <rcz@semihalf.com>
Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>
Signed-off-by: NStefan Roese <sr@denx.de>

There are two aspects of a TFTP transfer involving timeouts:
1. timeout waiting for initial server reply after sending RRQ
2. timeouts while transferring actual data from the server

Since the upcoming auto-update feature attempts a TFTP download during each
boot, it is undesirable to have a long delay when the TFTP server is not
available. Thus, this commit makes the server timeout (1.) configurable by two
global variables:

TftpRRQTimeoutMSecs
TftpRRQTimeoutCountMax

TftpRRQTimeoutMSecs overrides default timeout when trying to connect to a TFTP
server, TftpRRQTimeoutCountMax overrides default number of connection retries.
The total delay when trying to download a file from a non-existing TFTP server
is TftpRRQTimeoutMSecs x TftpRRQTimeoutCountMax milliseconds.

Timeouts during file transfers (2.) are unaffected.
Signed-off-by: NRafal Czubak <rcz@semihalf.com>
Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>

Enforce millisecond semantics of the first argument to NetSetTimeout() --
the change is transparent for well-behaving boards (CFG_HZ == 1000 and
get_timer() countiing in milliseconds).

Rationale for this patch is to enable millisecond granularity for
network-related timeouts, which is needed for the upcoming automatic
software update feature.

Summary of changes:
- do not scale the first argument to NetSetTimeout() by CFG_HZ
- change timeout values used in the networking code to milliseconds
Signed-off-by: NRafal Czubak <rcz@semihalf.com>
Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>

Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.
Signed-off-by: NRichard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>

Change UEC phy interface from GMII to RGMII on MPC8568MDS board

Because on MPC8568MDS, GMII interface is only recommended for 1000Mbps speed,
but RGMII interface can work at 10/100/1000Mbps, and RGMII interface works more stable.

Now both UEC1 and UEC2 can work properly under u-boot.

It is also in consistent with the kernel setting for 8568 UEC phy interface.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NBen Warren <biggerbadderben@gmail.com>

Fix compiler warning introduced by commit 0f8cbc18Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NWolfgang Denk <wd@denx.de>

Reference manual states that MxMR[MAD] increment is the indication
of write to UPM array is complete. Honour that. Also, make the dummy
write explicit.

also fix the comment.
Signed-off-by: NSelvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

Currently this is not creating any problem. But it will result
in compilation error when used as below.

printf("CFG_SDRAM_CFG2 - %08x\n", CFG_SDRAM_CFG2);
Signed-off-by: NSelvamuthukumar <selva.muthukumar@e-coninfotech.com>

continuation of the theme based on git grep "^#define CFG_.*;$" include/
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

Signed-off-by: NHugo Villeneuve <hugo.villeneuve@lyrtech.com>

This patch fixes a type mismatch and thus removes a compiler
warning when compiling with CONFIG_API on powerpc.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Original code displayed:
 => help i2c
 i2c i2c speed [speed] - show or set I2C bus speed
 i2c md chip address[.0, .1, .2] [# of objects] - read from I2C device
 ...
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

SGMII and SATA share the serdes on MPC8536 CPU, When SATA disabled and the
driver still try to access the SATA registers, the cpu will hangup.
This patch try to fix this by reading the serdes status before the SATA
initialize.
Signed-off-by: NJason Jin <Jason.jin@freescale.com>
Acked-by: NAndy Fleming <afleming@freescale.com>

When aligning malloc()ed screen_base, invalid offset was added.
This not only caused misaligned result (which did not cause hardware
misbehaviour), but - worse - caused screen_base + smem_len to
be out of malloc()ed space, which in turn caused breakage of
futher malloc()/free() operation.

This patch fixes screen_base alignment.

Also this patch makes memset() that cleans framebuffer to be executed
on first initialization of diu, not only on re-initialization. It looks
correct to clean the framebuffer instead of displaying random garbage;
I believe that was disabled only because that memset caused breakage
of malloc/free described above - which no longer happens with the fix
described above.
Signed-off-by: NNikita V. Youshchenko <yoush@debian.org>

This patch fixes building with CONFIG_API and CONFIG_USB_STORAGE.

USB_MAX_STOR_DEV is defined in include/usb.h, but
needed in api/api_storage.c.
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>

Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>

The checks for CFG_EEPROM_PAGE_WRITE_ENABLE and
CFG_EEPROM_PAGE_WRITE_BITS in various temperature
sensor drivers are not necessary
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>

Since we're working with unsigned data, you can't apply a signed pointer
cast and then attempt to print the result.  Otherwise you get wrong output
when the sign bit is set like "0xFF" incorrectly extended to "0xFFFFFFFF".
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We don't need CONFIG_CFG_STRINGS anymore now that we have the define
CONFIG_CMD_STRINGS and Makefile control.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

When the total size of all NAND devices exceeds 4 GiB, the size  will
overflow. This patch tries to fix this.

Note that we still have a problem when a single NAND device is bigger
than 4 GiB: then the overflow would actually happen earlier, i. e.
when storing the size in nand_info[].size, as nand_info[].size is an
"u_int32_t".
Signed-off-by: NJason Jin <Jason.jin@freescale.com>
Signed-off-by: NWolfgang Denk <wd@denx.de>