CPU board (E2530) has a fan - turn it on via GPIO to keep
the SoC cool.
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

The tegra-common-usb-gadget.h include was causing
some build problems in ci_udc.c with a 64-bit gcc
in an earlier version of the T210 patches, but it
is working fine now, so restore it.
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

This was done in the 32-bit AVP loader (SPL) but is
board-specific so should be moved to the CPU portion.
Signed-off-by: NTom Warren <twarren@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>

This config option isn't used anywhere at all. Remove all places that
define/enable the option.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Document the development flow on figuring out PIRQ information
during the U-Boot porting.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Remove DEBUG in drivers/pci/pci_compat.c.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

The code in question polls an USB port status via USB_REQ_GET_STATUS
to determine whether there is a device on the port or not. The way to
figure that out is to check two bits. Those are wPortChange[0] and
wPortStatus[0].

The wPortChange[0] indicates whether some kind of a connection status
change happened on a port (a device was plugged or unplugged). The
wPortStatus[0] bit indicates the status of the connection (plugged or
unplugged).

The current code tests whether wPortChange[0] == wPortStatus[0] and
if that's the case, considers the loop polling for the presence of a
USB device on port finished.

This works for most USB sticks, since they come up really quickly and
trigger the USB port change detection before the first iteration of the
detection loop happens. Thus, both wPortChange[0] and wPortStatus[0]
are set to 1 and thus equal. The loop is existed in it's first iteration
and the stick is detected correctly.

The problem is with some obscure USB sticks, which take some time before
they pop up on the bus after the port was enabled. In this case, both
the wPortChange[0] and wPortStatus[0] are 0. They are equal again, so
the loop again exits in the first iteration, but this is incorrect, as
such USB stick didn't have the opportunity to get detected on the bus.

Rework the code such, that it checks for wPortChange[0] first to test
if any connection change happened at all. If no change occured, keep
polling. If a change did occur, test the wPortStatus[0] to see there is
some device present on the port and only if this is the case, break out
of the polling loop.

This patch also trims down the duration of the polling loop from 10s
per port to 1s per port. This is still annoyingly long, but there is
no better option in case of U-Boot unfortunatelly. This change will
most likely increase the duration of 'usb start' on some platforms,
but this is needed to fix a bug.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>

This patch fixes operation of our on-board AX88772B chip without EEPROM
but with a ethaddr coming from the regular U-Boot environment. This is
a forward port of some remaining parts initially implemented by
Antmicro.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: NMarek Vasut <marex@denx.de>

USB_KEYBOARD is now defined in drivers/usb/Kconfig, drop our own duplicate
definition.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

usb_stor_reset is only defined when USB storage support is enabled, thus the
function is not declared when such support is missing.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

This adds some config options to the sunxi-common config to enable the USB
download gadget and the fastboot and USB mass storage functions.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

Currently, the second use of a gadget will fail, while the first one works.

Forcing the EP0 at every enable fix this issue.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that some things were updated in Kconfig, they should be reflected on the
sunxi-common config too.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

Now that the musb-new driver has a Kconfig, we can move Kconfig options to
enable controllers to it, so that it's easier in e.g. menuconfig.

In addition, this allows declaring support for USB_MUSB_HOST/GADGET in
defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected
automatically when needed.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

Having MUSB_HOST and MUSB_GADGET in Kconfig allows more flexibility with regard
to what Kconfig options to enable, such as USB_STORAGE or USB_KEYBOARD.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

There is no particular reason why the USB Kconfig option should be specific to
host mode. In prevision of adding MUSB host and gadget to Kconfig, this moves
the title and help message of the USB Kconfig option to a more generic format.

Adding comments to the usb Kconfig allows for a better separation and more
readability in generated configs and in menuconfig.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

The USB_ARCH_HAS_HCD currently serves no purpose and adds some confusion to the
required Kconfig options that are required to have USB support.

Dropping it makes things easier and doesn't break anything, since it was unused
anyways.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>

This patch makes the dwc2 controller like ehci / ohci / xhci controllers
by calling the board_usb_init() function from usb_lowlevel_init.

This can then be implemented by specific platforms to initialise
their USB hardware (phys / clocks etc).
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>

Add some documentation on the EFI implementation in U-Boot.
Signed-off-by: NBen Stoltz <stoltz@google.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

We cannot use this driver when running from EFI as we have no direct hardware
access. In fact coreboot uses a different driver which uses tables provided
by coreboot. So far it does not seem possible to use a normal video driver
when booting from EFI.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NAnatolij Gustschin <agust@denx.de>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Disable a few things which interfere with the EFI init. This allows QEMU to
to boot into EFI, load a U-Boot payload then boot to the U-Boot prompt.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Tested-by: NBin Meng <bmeng.cn@gmail.com>

Disable a few things which interfere with the EFI init. This allows the
Minnowboard MAX to boot into EFI, load a U-Boot payload then boot to the
U-Boot prompt.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

When U-Boot is running from EFI some of the x86 init is replaced with
EFI-specific init. For example, since DRAM has already been set up, we only
need to find it, not init it. Add these functions so that boards can easily
allow booting from EFI if required.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

When U-Boot runs as an EFI payload it needs to avoid setting up the CPU
again. Also U-Boot currently does not handle interrupts for many devices, so
run with interrupts disabled.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

The EFI memory map is passed from the stub to U-Boot in a table. Add a
command to display it in a vaguely readable fashion.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Tested on QEMU
Tested-by: NBin Meng <bmeng.cn@gmail.com>

The EFI stub can pass a table to U-Boot with information about the memory map
Potentially other things will follow. Add a way to access this table.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

The EFI stub provides information to U-Boot in a table. This includes the
memory map which is needed to decide where to relocate U-Boot. Collect this
information in the early init code and store it in global_data.

Fix up the BIST code at the same time since we don't have it when booting
from EFI and can assume it is 0.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Most EFI implementations use 64-bit. Add a way to build U-Boot as a 64-bit
EFI payload. The payload unpacks a (32-bit) U-Boot and starts it. This can
be enabled for x86 boards at present.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Tested-by: NBin Meng <bmeng.cn@gmail.com>

The procedure to drop from 64-bit mode to 32-bit is a bit messy. Add a
function to take care of it. It requires identity-mapped pages and that
the calling code is running below 4GB.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Rather than add these as open-coded values, create an enum with the commonly
used flags.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Add support for building a 32/64-bit EFI stub for x86. This involves
building the startup and relocation code for either i386 or x86_64.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

It is useful to be able to load U-Boot onto a board even if is it already
running EFI. This can allow access to the U-Boot command interface, flexible
booting options and easier development.

The easiest way to do this is to build U-Boot as a binary blob and have an
EFI stub copy it into RAM. Add support for this feature, targeting 32-bit
initially.

Also add a way to detect when U-Boot has been loaded via a stub. This goes
in common.h since it needs to be widely available so that we avoid redoing
initialisation that should be skipped.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Tested-by: NBin Meng <bmeng.cn@gmail.com>

Add a linker script and relocation code for building 64-bit EFI
applications. This can be used for the EFI stub.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

Add configuration and Kconfig changes for this board.
Signed-off-by: NBen Stoltz <stoltz@google.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

This code currently requires CONFIG_SYS_TEXT_BASE but this should be
unnecessary. As a first step, remove the build-time limitation and report an
error instead.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

This contains just enough to bring up the serial UART.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Tested-by: NBin Meng <bmeng.cn@gmail.com>

Add support for the efi-x86 board, which supports running U-Boot as an
EFI 32-bit application.
Signed-off-by: NBen Stoltz <stoltz@google.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Tested-by: NBin Meng <bmeng.cn@gmail.com>

Add the required x86 glue code. This includes the initial start-up,
relocation and jumping to efi_main(). We also need to avoid fiddling with
interrupts.
Signed-off-by: NBen Stoltz <stoltz@google.com>
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>