In some cases we were missing CONFIG_USB=y so enable that when needed.
Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NTom Rini <trini@konsulko.com>

If both SPL_DM and SPL_OF_CONTROL are enabled, SPL needs to bind
several devices, but CONFIG_SYS_MALLOC_F_LEN=0x400 is apparently
not enough.  Increase the default to 0x2000 for the case.  This
will be helpful for shorter defconfigs.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NStefan Roese <sr@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

An issue in the TI secure image generation tool causes the ROM to
load the SPL at a different load address than what is specified by
CONFIG_ISW_ENTRY_ADDR while doing a peripheral boot on HS devices.

This causes the SPL to fail on secure devices during peripheral
boot.

The TI secure image generation tool has been fixed so that the SPL
will always be loaded at 0x403018E0 by the ROM code for both
peripheral and memory boot modes.
Signed-off-by: NMadan Srinivas <madans@ti.com>
Reviewed-by: NNishanth Menon <nm@ti.com>
Acked-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Enable the platform-specific post-processing of FIT-extracted blobs such
as Kernel, DTB, and initramfs on TI AM57xx high-security (HS) devices
which will ultimately invoke a ROM-based API call that performs secure
processing such as blob authentication.
Signed-off-by: NAndreas Dannenberg <dannenberg@ti.com>
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Enable the platform-specific post-processing of FIT-extracted blobs such
as Kernel, DTB, and initramfs on TI DRA7xx high-security (HS) devices
which will ultimately invoke a ROM-based API call that performs secure
processing such as blob authentication.
Signed-off-by: NAndreas Dannenberg <dannenberg@ti.com>
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Enable the platform-specific post-processing of FIT-extracted blobs such
as Kernel, DTB, and initramfs on TI AM43xx high-security (HS) devices
which will ultimately invoke a ROM-based API call that performs secure
processing such as blob authentication.
Signed-off-by: NAndreas Dannenberg <dannenberg@ti.com>
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.

However, in such a configuration the serial controller gets its rx queue filled
up with zero bytes which then happily get transmitted on to whoever calls
getc() today.

This patch adds detection logic for that case by checking whether the RX pin is
mapped to GPIO15 and disables the mini uart if it is not mapped properly.

That way we can leave the driver enabled in the tree and can determine during
runtime whether serial is usable or not, having a single binary that allows for
uart and non-uart operation.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

NXP kernel expects to boot in secure mode, so introduce
warp7_secure_defconfig target which selects CONFIG_ARMV7_BOOT_SEC_DEFAULT.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>

Since commit a13d3757 ("warp: Use imx_ddr_size() for calculating the
DDR size") warp board no longer boots.

The reason for the breakage is that the warp board is using the DDR
configuration from mx6slevk. A fundamental difference between warp and
mx6slevk is that warp only uses one DDR chip select while mx6slevk uses two.

The imx_ddr() function calculates the RAM size in runtime by reading the
values of registers MDCTL and MDMISC.

So in order to fix this warp boot issue, create a imximage DDR file specific
to warp, where the MDCTL register is configured to only activates a single
chip select.
Reported-by: NBreno Lima <breno.lima@nxp.com>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Tested-by: NBreno Lima <breno.lima@nxp.com>

Add support for Advantech DMS-BA16 board. The board is based on Advantech
BA16 module which has a i.MX6D processor. The board supports:
 - FEC Ethernet
 - USB Ports
 - SDHC and MMC boot
 - SPI NOR
 - LVDS and HDMI display

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6D
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Cc: u-boot@lists.denx.de
Cc: sbabic@denx.de

The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.

The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

The Orange Pi 2 and Orange Pi Plus also come with ethernet, enable
support for this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

A33-OLinuXino is A33 development board designed by Olimex LTD.

It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.

It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.

The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: NStefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

The iNet D978 rev2 is a tablet board designed by iNet, which is intended to
use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB
RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

The Colorado TK1 SOM is a small form factor board similar to the
Jetson TK1.  The main differences lie in the pinmux, and in that the
PCIe controller is set to use in 4lanes+1lane, rather than 2+2.

The pinmux header here was generated from a spreadsheet provided by
Colorado Engineering using the tegra-pinmux scripts.  The spreadsheet
was converted from v09 to v11 by me.
Signed-off-by: NPeter Chubb <peter.chubb@data61.csiro.au>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

The board ID EEPROM and board ID stickers on p2771-0000 will use a numeric
versioning scheme, with version numbers such as 000/100/200/300/400/500.
Within NVIDIA, these versions are also known as A00/A01/A02/A03/A04/B00.
However, that numbering scheme is not easily visible outside of NVIDIA,
and so does not make much sense to use. Convert U-Boot to use the readily
visible numeric scheme.

Also, it turns out that the current A02 DT actually applies to board
versions 000/100/200 (A00..A02). Consequently rename this to 000 not 200
so that all U-Boot builds are named after the first version of the HW they
support.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

This introduces two board defconfig files for generating EFI 32-bit
and 64-bit payloads, to run on QEMU x86 target.

With these in place, hopefully buildman will catch any build error
with EFI payload support on x86.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This will be useful, for example, to load firmware to DRAM and make
it visible to other agents.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

This is very likely to be necessary for normal use cases.
Set its default to 'y' for shorter defconfig files.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Commit 76c52ce2 ("ARM: uniphier: increase CONFIG_SYS_MALLOC_F_LEN
to bind all nodes") missed to increase this config for sLD3.

This change is needed to add "u-boot,dm-pre-reloc" to some nodes;
more devices are bound, more malloc memory is needed.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.

The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.

Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

Add a defconfig and dts file for tablets using the generic inet-q972 PCB.

Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.

This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.

The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

- move bcm23550_w1d to Kconfig
- move bcm28155_ap to Kconfig
Signed-off-by: NSteve Rae <steve.rae@raedomain.com>

This moves some config from config files.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

This updated defconfig following boards:
 - Alt
 - Gose
 - Koelsh
 - Lager
 - Porter
 - Silk
 - Stout
 - Blanche
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

BLANCHE is development board based on R-Car V2H SoC (R8A7792)

This commit supports the following periherals:
- SCIF, Ethernet, QSPI, MMC
Signed-off-by: NMasakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Salvator-x is an entry level development board based on
R-Car H3 SoC (R8A7795). This commit supports SCIF only.
Signed-off-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

This patch adds support for the BayTrail based theadorable-x86-dfi-bt700
board which uses the DFI BT700 BayTrail Qseven SoM on a custom baseboard.
The main difference to the DFI baseboard is, that it isn't equipped
with a Super IO chip and uses the internal HS SIO UART (memory mapped
PCI based) as the console UART.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

This patch adds support for the DFI BayTrail BT700 QSeven SoM installed
on the DFI Q7X-151 baseboard. The baseboard is equipped with the Nuvoton
NCT6102D Super IO chip providing the UART as console.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

This patch includes the following changes:

- Remove Designware I2C support from dts as its not used
- Configure SMBus PADs in dts
- Enable I2C commands and I2C support
- Configure SMSC2513 USB hub via SMBus upon startup
- Move environment location to match Minnowmax example
- Enhancement of the default environment
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

K2G can benefit from driver model support in the
MMC/SD driver it uses: omap_hsmmc

Enable driver model MMC support for K2G.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

The 'xtfpga' board is actually a set of FPGA evaluation boards that
can be configured to run an Xtensa processor.

 - Avnet Xilinx LX60
 - Avnet Xilinx LX110
 - Avnet Xilinx LX200
 - Xilinx ML605
 - Xilinx KC705

These boards share the same components (open-ethernet, ns16550 serial,
lcd display, flash, etc.).
Signed-off-by: NChris Zankel <chris@zankel.net>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the
only board configuration that uses it and put it into that board's
defconfig.

Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

p2771-0000 has a couple of PCIe ports; one physically x4 desktop PCI
connector (which may run at x2 electrically, depending on the board
version and configuration) and a x1 connection to the M.2 slot (which may
not be active, depending on the board version and configuration). This
change enables those.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Now that clock and reset drivers exist for Tegra186, we can enable the SD
card controller. Now that a BPMP I2C driver exists for Tegra186, we can
communicate with the PMIC to enable power to the SD card. Hook up the DT
content and board code required to make the SD card work.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Enable eth driver model for am43xx_evm as cpsw supports
driver model.

This was already added with the commit bc705ea1 but with
commit 4c4e3b37 to add fit support CONFIG_DM_ETH was missed.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>