- 02 5月, 2021 5 次提交
-
-
由 Ian Ray 提交于
Disable the unused persistent environment. Signed-off-by: NIan Ray <ian.ray@ge.com> Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.com>
-
由 Ian Ray 提交于
Increase watchdog period, in order to accomodate recent kernel size and configuration changes. Signed-off-by: NIan Ray <ian.ray@ge.com> Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.com>
-
由 Sebastian Reichel 提交于
Add PHY's reset GPIO, so that U-Boot does a PHY hard reset. This is needed, since the PHY might become unresponsive if watchdog reboots the system while a transaction is ongoing. The reset GPIO is added to the U-Boot specific DT files, since the kernel does not setup the reserved registers correctly after resetting the PHY and thus must not reset it. Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.com>
-
由 Sebastian Reichel 提交于
The DA9063 enables the CRYSTAL bit by default, but there is no crystal populated on the BA16 system on module. Without explicitly clearing the CRYSTAL bit the system runs unstable and sometimes reboots unexpectedly. Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.com>
-
由 Marek Vasut 提交于
In case binman is enabled, the u-boot.itb is generated using this tool and there is no direct u-boot.itb target, but instead the binman tool must be invoked. Add support for this case. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
-
- 30 4月, 2021 1 次提交
-
-
https://source.denx.de/u-boot/custodians/u-boot-dm由 Tom Rini 提交于
buildman environment fix binman FMAP improvements minor test improvements and fixes minor dm improvements
-
- 29 4月, 2021 34 次提交
-
-
https://source.denx.de/u-boot/custodians/u-boot-microblaze由 Tom Rini 提交于
Xilinx changes for v2021.07-rc2 xilinx: - Enable saving variables based on bootmode - Cleanup usb dfu setup and wire it up with usb bootmode - Fix bootscript address logic - Remove GD references (spi, Versal) - Enable capsule update clk: - Small Kconfig fix net: - Fix gmii2rgmii bridge binding usb: - Propagate error (dfu gadget)
-
由 Michal Simek 提交于
gd is not used in this file that's why doesn't make sense to declare it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
https://source.denx.de/u-boot/custodians/u-boot-cfi-flash由 Tom Rini 提交于
- mtd: cfi: Fix PPB lock status readout (Marek)
-
https://source.denx.de/u-boot/custodians/u-boot-marvell由 Tom Rini 提交于
- Add base support for Marvell OcteonTX2 CN9130 CRB (mostly done by Kostya) - Sync Armada 3k/7k/8k SERDES code with Marvell version (misc Marvell authors) - pci-aardvark: Fix processing PIO transfers (Pali)
-
由 Heinrich Schuchardt 提交于
Add a reference for the TPM event types and provide missing constants. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
-
由 Chen Guanqiao 提交于
Add test item for getting address and size functions Test the following function: - ofnode_get_addr() - ofnode_get_size() Signed-off-by: NChen Guanqiao <chenguanqiao@kuaishou.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Chen Guanqiao 提交于
Add functions to add size of addresses in the device tree using ofnode references. If the size is not set, return FDT_SIZE_T_NONE. Signed-off-by: NChen Guanqiao <chenguanqiao@kuaishou.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present we sometimes see problems in gitlab where the environment has 0x80 characters or sequences which are not valid UTF-8. Avoid this by using bytes for the environment, both internal to buildman and when writing out the 'env' file. Add a test to make sure this works as expected. Reported-by: NMarek Vasut <marex@denx.de> Fixes: e5fc79ea ("buildman: Write the environment out to an 'env' file") Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
There have been at least a few cases where an exception has occurred in a thread and resulted in buildman hanging: running out of disk space and getting a unicode error. Handle these by collecting a list of exceptions, printing them out and reporting failure if any are found. Add a test for this. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present the code to report a build result is duplicated. Put it in a common function to avoid this. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Add some function comments which are missing, or missing arguments. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Sean Anderson 提交于
If there are no nodes or if all nodes are disabled, this function would return err without setting it first. Fix this by initializing err to zero. Fixes: 94f7afdf ("dm: core: Ignore disabled devices when binding") Signed-off-by: NSean Anderson <sean.anderson@seco.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Patrick Delaunay 提交于
Today of_address_to_resource() is called only in ofnode_read_resource() for livetree support and fdt_get_resource() is called when livetree is not supported. The fdt_get_resource() doesn't do the address translation so when it is required, but the address translation is done by ofnode_read_resource() caller, for example in drivers/firmware/scmi/smt.c::scmi_dt_get_smt_buffer() { ... ret = ofnode_read_resource(args.node, 0, &resource); if (ret) return ret; faddr = cpu_to_fdt32(resource.start); paddr = ofnode_translate_address(args.node, &faddr); ... The both behavior should be aligned and the address translation must be called in fdt_get_resource() and removed for each caller. Fixes: a4481012 ("dm: core: Add dev_read_resource() to read device resources") Signed-off-by: NPatrick Delaunay <patrick.delaunay@foss.st.com> Acked-by: NEtienne Carriere <etienne.carriere@linaro.org>
-
由 Simon Glass 提交于
When used with hierarchical images, use the Chromium OS convention of adding a section before all the subentries it contains. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
Use an interator in two of the fmap tests so it is easier to add new items. Also check the name first since that is the first indication that something is wrong. Use a variable for the expected size of the fmap to avoid repeating the code. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Evan Benn 提交于
Parse each empty-line-delimited message separately. This saves having to deal with all the different line content styles, we only care about the header ERROR | WARNING | NOTE... Also make checkpatch print line information for a uboot specific warning. Signed-off-by: NEvan Benn <evanbenn@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Tom Rini 提交于
Given that we have tests that require pygit2 and it can be installed like any other python module, fail much more loudly if it is missing. Cc: Simon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
The patman tests require the requests module, add it. Cc: Simon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Given that test/py/requirements.txt has all required test modules, make use of that rather than a manual pip install list before running our assorted tool testsuites. Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Andy Shevchenko 提交于
It is easier to read the positive conditional. While at it, convert hard coded length of "_test_" to strlen("_test_") which will be converted to a constant bu optimizing compiler. Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Andy Shevchenko 提交于
When run `ut dm [test name]` allow to use simple pattern to run all tests started with given prefix. For example, to run all ACPI test cases: ut dm acpi* Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
At present each invocation of run_steps() updates OUTPUT_FILES_COMMON, since it does not make a copy of the dict. This is fine for a single invocation, but for tests, run_steps() is invoked many times. As a result it may include unwanted items from the previous run, if it happens that a test runs twice on the same CPU. The problem has not been noticied previously, as there are few enough tests and enough CPUs that is is rare for the 'wrong' combination of tests to run together. Fix this by making a copy of the dict, before updating it. Update the tests to suit, taking account of the files that are no-longer generated. With this fix, we no-longer generate files which are not needed for a particular state of OF_PLATDATA_INST, so the check_instantiate() function is not needed anymore. It has become dead code and so fails the code-coverage test (dtoc -T). Remove it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
These two tests require an ELF image so that symbol information can be written into the SPL/TPL binary. At present they rely on other tests having set it up first, but every test must run independently. This can cause occasional errors in CI. Fix this by setting up the required files, as other tests do. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Michal Simek 提交于
The commit 6c993815 ("net: phy: xilinx: Be compatible with live OF tree") change driver behavior to while loop which wasn't correct because the driver was looping over again and again. The reason was that ofnode_valid() is taking 0 as correct value. Fix it by changing while loop to ofnode_for_each_subnode() which is only loop over available nodes. Fixes: 6c993815 ("net: phy: xilinx: Be compatible with live OF tree") Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Pali Rohár 提交于
Trying to clear PIO_START register when it is non-zero (which indicates that previous PIO transfer has not finished yet) causes an External Abort with SError 0xbf000002. This bug is currently worked around in TF-A by handling External Aborts in EL3 and ignoring this particular SError. This workaround was also discussed at: https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50 https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/ https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/ https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541 Implement a proper fix to prevent this External Abort. As it is not possible to cancel a pending PIO transfer, simply do not start a new one if previous has not finished yet. In this case return an error to the caller. In most cases this SError happens when there is no PCIe card connected or when PCIe link is down. The reason is that in these cases a PIO transfer takes about 1.44 seconds. For this reason we also increase the wait timeout in pcie_advk_wait_pio() to 1.5 seconds. If PIO read transfer for PCI_VENDOR_ID register times out, or if it isn't possible to read it yet because previous transfer is not finished, return Completion Retry Status value instead of failing, to give the caller a chance to send a new read request. Signed-off-by: NPali Rohár <pali@kernel.org> Reviewed-by: NMarek Behún <marek.behun@nic.cz> Reviewed-by: NStefan Roese <sr@denx.de>
-
由 Igal Liberman 提交于
Change-Id: I29094afb646744afe78ad09bb7479894d1a65e96 Signed-off-by: NIgal Liberman <igall@marvell.com>
-
由 Grzegorz Jaszczyk 提交于
- Add additional step which enables the Impedance and PLL calibration. - Enable old squelch detector instead of the new analog squelch detector circuit and update host disconnect threshold value. - Update LS TX driver strength coarse and fine adjustment values. Change-Id: Ifa0a585bfb5ecab0bfa033eed6874ff98b16a7df Signed-off-by: NGrzegorz Jaszczyk <jaz@semihalf.com>
-
由 Igal Liberman 提交于
In CP115, comphy4 can be configured into SFI port1 (in addition to SFI0). This patch adds the option described above. In addition, rename all existing SFI/XFI references: COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0 No functional change for exsiting configuration. Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0 Signed-off-by: NIgal Liberman <igall@marvell.com> Signed-off-by: NKonstantin Porotchkin <kostap@marvell.com>
-
由 Grzegorz Jaszczyk 提交于
According to Design Reference Specification the PHY PLL and Calibration register from PHY0 are shared for multi-port PHY. PLL control registers inside other PHY channels are not used. This commit reworks utmi device tree nodes in a way that common PHY PLL registers are moved to main utmi node. Accordingly both child nodes utmi-unit range is reduced and register offsets in utmi_phy.h are updated to this change. This fixes issues in scenarios when only utmi port1 was in use, which resulted with lack of correct pll initialization. Change-Id: Icc520dfa719f43a09493ab31f671efbe88872097 Signed-off-by: NGrzegorz Jaszczyk <jaz@semihalf.com>
-
由 Grzegorz Jaszczyk 提交于
New products can contain up to 6 usb ports, therefore allow to initialize all relevant UTMI PHYs. Change-Id: I28c36e59fa0e3e338bb3ee0cee2240b923f39785 Signed-off-by: NGrzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: NKostya Porotchkin <Kostya.Porotchkin@cavium.com>
-
由 Igal Liberman 提交于
It helps ATF to determine who called power off function (U-boot/Linux) and act accordingly Change-Id: Icfc5cbfdba64754496812154272b28c0ff639f0f Signed-off-by: NIgal Liberman <igall@marvell.com> Reviewed-by: NGrzegorz Jaszczyk <jaz@semihalf.com>
-
由 Christine Gharzuzi 提交于
- the default value of comphy pipe selector is set to PCIe (x4) in case of unconnected comphy the default value remains 0x4 which may lead to several issues with comphy initialization. - this patch adds SMC call that powers off the comphy lane in case of unconnected comphy. Change-Id: I196b2916518dd8df3b159ffa85e2989b8e483087 Signed-off-by: NChristine Gharzuzi <chrisg@marvell.com> Signed-off-by: NIgal Liberman <igall@marvell.com> Reviewed-by: NGrzegorz Jaszczyk <jaz@semihalf.com>
-
由 Igal Liberman 提交于
Currently, we don't pass id for SGMII 0/1. A bug in comphy selector configuration was found (in comphy firmware), after fixing it, SGMII0/1 have different configuration, so we need to pass the ID the firmware. Change-Id: Idcff4029cc9cf018278e493221b64b33574e0d38 Signed-off-by: NIgal Liberman <igall@marvell.com> Reviewed-by: NGrzegorz Jaszczyk <jaz@semihalf.com>
-
由 Grzegorz Jaszczyk 提交于
Change-Id: I358792a96c13b54e700c05227cc7a8f6bd584694 Signed-off-by: NGrzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: NIgal Liberman <igall@marvell.com>
-