- 16 4月, 2013 1 次提交
-
-
由 Tom Warren 提交于
Beaver is a Tegra30 board that is nearly 100% compatible w/Cardhu. Add a Beaver build so it can begin to be differentiated, if need be. Signed-off-by: NTom Warren <twarren@nvidia.com> Reviewed-by: NStephen Warren <swarren@nvidia.com>
-
- 13 4月, 2013 1 次提交
-
-
由 Holger Brunck 提交于
This board is from a u-boot point of view a mixture between kmnusa and a standard km_kirkwood board. We have our u-boot environment in the spi NOR flash, but we have a direct connection between the kirkwood and the piggy. A FPGA is connected via the PCIe interface. So we only have to select the specific features in the board setup. Signed-off-by: NHolger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-By: NPrafulla Wadaskar <prafulla@marvell.com>
-
- 12 4月, 2013 1 次提交
-
-
由 Benoît Thébaudeau 提交于
This also fixes support for mx31pdk and tx25, which had been broken by commit e05e5de7. Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com> Acked-by: NScott Wood <scottwood@freescale.com> Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 08 4月, 2013 1 次提交
-
-
由 SRICHARAN R 提交于
The omap5-uevm is the reference board name for OMAP5 soc based platform. So rename it accordingly. Acked-by: NNishanth Menon <nm@ti.com> Signed-off-by: NSricharan R <r.sricharan@ti.com> Tested-by: NNishanth Menon <nm@ti.com>
-
- 03 4月, 2013 1 次提交
-
-
由 Fabio Estevam 提交于
Introduce 'mx28evk_nand' target for saving environment variables into NAND. The mx28evk board does not come with a NAND flash populated from the factory. It comes with an empty slot (U23), which allows the insertion of a 48-pin TSOP flash device. Tested with a K9LBG08U0D. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Reviewed-by: NOtavio Salvador <otavio@ossystems.com.br>
-
- 25 3月, 2013 1 次提交
-
-
由 Matt Porter 提交于
Add TI814X EVM board directory, config file, and MAINTAINERS entry. Enable build. Signed-off-by: NMatt Porter <mporter@ti.com> Reviewed-by: NTom Rini <trini@ti.com> [trini: Adapt to recent omap_hsmmc requirements, Matt re-tested] Signed-off-by: NTom Rini <trini@ti.com>
-
- 20 3月, 2013 1 次提交
-
-
由 Fabio Estevam 提交于
Wandboard is a development board that has two variants: one version based on mx6 dual lite and another one based on mx6 solo. For more details about Wandboard, please refer to: http://www.wandboard.org/Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 15 3月, 2013 1 次提交
-
-
由 Fabio Estevam 提交于
Fix the following build error when buildig nitrogen6s1g: nitrogen6x.c:89:17: error: 'CONFIG_DDR_MB' undeclared (first use in this function) nitrogen6x.c:89:17: note: each undeclared identifier is reported only once for each function it appears in Reported-by: NAlbert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 13 3月, 2013 1 次提交
-
-
由 Eric Nelson 提交于
Signed-off-by: NEric Nelson <eric.nelson@boundarydevices.com>
-
- 12 3月, 2013 2 次提交
-
-
由 Rajeshwari Shinde 提交于
This patch adds the configuration file for Snow Board and defines the same in boards.cfg. Signed-off-by: NRajeshwari Shinde <rajeshwari.s@samsung.com> Acked-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Stefan Roese 提交于
These boards seem to be unmaintained for quite some time. So lets remove support for them completely. This also cleans up some common drivers/files. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch> Acked-by: NWolfgang Denk <wd@denx.de>
-
- 11 3月, 2013 1 次提交
-
-
由 Lokesh Vutla 提交于
Adding the build support for dra7xx_evm. Reusing omap5_evm.h config by moving it to omap5_common.h Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NR Sricharan <r.sricharan@ti.com>
-
- 09 3月, 2013 3 次提交
-
-
由 Anatolij Gustschin 提交于
Add new mpc5121e based ac14xx board and a new pinmux config function for setting individual pinmux bit groups. This function is used in ac14xx board code. Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
由 Stefan Roese 提交于
This patch adds the a4m2k MPC5200B board port. Its a derivate of the a3m071 board with only minor changes. Additionally this patch includes some clean-up changes: - Remove I2C support from a3m071 as its unused - Fix/enhance default env variables - Fix some comments - Add newly introduced CONFIG_SPL_TARGET to automatically build "u-boot-img.bin" - Fix dtb patching in READ desciption for SPL Linux booting: "fdt chosen" needs to get called to patch/create the chosen node. - Add missing call to spl_board_init(): Define CONFIG_SPL_BOARD_INIT so that spl_board_init() will get called in the SPL version. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Tom Rini 提交于
We add USB (RNDIS gadget) SPL support as a separate target. We need to pull out YMODEM support in order to be a small enough target binary. Signed-off-by: NTom Rini <trini@ti.com>
-
- 04 3月, 2013 1 次提交
-
-
由 Sonic Zhang 提交于
Board and config header files for bf609-ezkit support. Signed-off-by: NBob Liu <lliubbo@gmail.com> Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NSonic Zhang <sonic.adi@gmail.com>
-
- 19 2月, 2013 3 次提交
-
-
由 Bo Shen 提交于
Add at91sam9g20_2mmc nand boot support. on this board, there is no dataflash, so disable it change one commet for at91sam9g20ek board Signed-off-by: NBo Shen <voice.shen@atmel.com> Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
由 Tom Rini 提交于
This target will move the environment into SPI flash and documents the expected layout. We correct the SPL define for where U-Boot is and remove an unused define. Signed-off-by: NTom Rini <trini@ti.com>
-
由 Enric Balletbo i Serra 提交于
The IGEP COM PROTON is a new ultra compact module design with an on-board ethernet controller. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
-
- 16 2月, 2013 2 次提交
-
-
由 Holger Brunck 提交于
This board is similar to TUXX1 but it has a different sized second FPGA. Therefore the configuration for the third chipselect is different. Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
-
由 Holger Brunck 提交于
This is a preparation for the upcoming kmopti2 board. This board has also a second fpga on board which is different to the tuxx1 target. But we want to use the same header file. So remove the config option KM_DISABLE_APP2 and simply use the board names to distinguish the features. Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
-
- 15 2月, 2013 1 次提交
-
-
由 Simon Glass 提交于
These are no longer used and should be removed. Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NGraeme Russ <graeme.russ@gmail.com>
-
- 12 2月, 2013 1 次提交
-
-
由 Tom Warren 提交于
This build is stripped down. It boots to the command prompt. GPIO is the only peripheral supported. Others TBD. Signed-off-by: NTom Warren <twarren@nvidia.com>
-
- 07 2月, 2013 3 次提交
-
-
由 Lars Poeschel 提交于
The board is named pcm051 and has this hardware: SOC: TI AM3359 DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB ETH 1: LAN8710AI SPI-Flash: W25Q64BVSSIG RTC: RV-4162-C7 I2C-EEPROM: CAT32WC32 NAND: MT29F4G08_VFPGA63 PMIC: TPS65910A3 LCD Supported: UART 1 MMC/SD ETH 1 USB I2C SPI Not yet supported: NAND RTC LCD Signed-off-by: NLars Poeschel <poeschel@lemonage.de> [trini: Add #define CONFIG_PHY_ADDR 0 to config] Signed-off-by: NTom Rini <trini@ti.com>
-
由 Javier Martinez Canillas 提交于
Even when the IGEPv2 board and the IGEP Computer-on-Module are different from a form factor point of view, they are very similar in the fact that share many components and how they are wired. So, it is possible (and better) to have a single board file for both devices and just use the CONFIG_MACH_TYPE to make a differentiation between each board when needed. This change avoids code duplication by removing 298 lines of code and makes future maintenance easier. Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
-
由 Michal Simek 提交于
Enable DCC driver for arm zynq platform to be compiled. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 31 1月, 2013 2 次提交
-
-
由 Prabhakar Kushwaha 提交于
BSC9132QDS is a Freescale reference design board for BSC9132 SoC. BSC9132 SOC is an integrated device that targets the evolving Microcell, Picocell, and Enterprise-Femto base station market subsegments. It combines Power Architecture e500v2 and DSP StarCore SC3850 core technologies with MAPLE-B2F baseband acceleration processing elements. BSC9132QDS Overview -------------------- 2Gbyte DDR3 (on board DDR), Dual Ranki 32Mbyte 16bit NOR flash 128Mbyte 2K page size NAND Flash 256 Kbit M24256 I2C EEPROM 128 Mbit SPI Flash memory SD slot USB-ULPI eTSEC1: Connected to SGMII PHY eTSEC2: Connected to SGMII PHY PCIe CPRI SerDes I2C RTC DUART interface: supports one UARTs up to 115200 bps for console display Apart from the above it also consists various peripherals to support DSP functionalities. This patch adds support for mainly Power side functionalities and peripherals Signed-off-by: NNaveen Burmi <NaveenBurmi@freescale.com> Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 York Sun 提交于
B4860QDS is a high-performance computing evaluation, development and test platform supporting the B4860 QorIQ Power Architecture processor. B4860QDS Overview ------------------ - DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 4 GB of memory in two ranks of 2 GB. - DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank. - SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point 16x16 switch VSC3316 - SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point 8x8 switch VSC3308 - USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode. - B4860 UART port is available over USB-to-UART translator USB2SER or over RS232 flat cable. - A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA connector ports 0 and 2 for AMC mode. - The B4860 configuration may be loaded from nine bits coded reset configuration reset source. The RCW source is set by appropriate DIP-switches: - 16-bit NOR Flash / PROMJet - QIXIS 8-bit NOR Flash Emulator - 8-bit NAND Flash - 24-bit SPI Flash - Long address I2C EEPROM - Available debug interfaces are: - On-board eCWTAP controller with ETH and USB I/F - JTAG/COP 16-pin header for any external TAP controller - External JTAG source over AMC to support B2B configuration - 70-pin Aurora debug connector - QIXIS (FPGA) logic: - 2 KB internal memory space including - IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK, DDRCLK1, 2 and RTCCLK. - Two 8T49N222A SerDes ref clock devices support two SerDes port clocks - total four refclk, including CPRI clock scheme Signed-off-by: NYork Sun <yorksun@freescale.com> Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: NShaveta Leekha <shaveta@freescale.com> Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com> Signed-off-by: NSandeep Singh <Sandeep@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
- 28 1月, 2013 1 次提交
-
-
由 Otavio Salvador 提交于
The following features are supported: * 128 MB DDR1 SDRAM * DUART * SD/MMC Card Socket Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
-
- 21 1月, 2013 1 次提交
-
-
由 Marek Vasut 提交于
This patch adds support for MX23-based Olinuxino board. Signed-off-by: NMarek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
-
- 17 1月, 2013 1 次提交
-
-
由 Tom Warren 提交于
This build is stripped down. It boots to the command prompt. GPIO is the only peripheral supported. Others TBD. include/configs/tegra-common.h now holds common config options for Tegra SoCs. Signed-off-by: NTom Warren <twarren@nvidia.com> Reviewed-by: NStephen Warren <swarren@nvidia.com>
-
- 12 1月, 2013 1 次提交
-
-
由 Bo Shen 提交于
Add dataflash boot support on at91sam9x5ek board Signed-off-by: NBo Shen <voice.shen@atmel.com> Acked-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 09 1月, 2013 1 次提交
-
-
由 Albert ARIBAUD 提交于
Signed-off-by: NAlbert ARIBAUD <albert.u.boot@aribaud.net>
-
- 20 12月, 2012 3 次提交
-
-
由 Yoshihiro Shimoda 提交于
The R0P7752C00000RZ board has SH7752, 512MB DDR3-SDRAM, SPI ROM, Gigabit Ethernet, and eMMC. This patch supports the following functions: - 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMC Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Scott Wood 提交于
This converts MPC8313ERDB NAND boot to use the new SPL infrastructure. Signed-off-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
* By a sequence of unfavorable conditions in the config header file, the eb_cpu5282 booting from internal stopped after relocation. Blame it is a faulty value of CONFIG_SYS_MONITOR_BASE. This patch fix this by replace the wrong condition in config header with option in board.cfg Signed-off-by: NJens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
-
- 07 12月, 2012 1 次提交
-
-
由 Gabe Black 提交于
Because calculate_relocation_address now uses the e820 map, it will be able to avoid addresses over 32 bits and regions that are at high addresses but not big enough for U-Boot. It also means we can remove the hack which limitted U-Boot's idea of the size of memory to less than 4GB. Also take into account the space needed for the heap and stack, so we avoid picking a very small region those areas might overlap with something it shouldn't. Signed-off-by: NGabe Black <gabeblack@chromium.org> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 06 12月, 2012 1 次提交
-
-
由 Stefan Roese 提交于
This patch adds support for the a3m071 board based on the MPC5200. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 28 11月, 2012 2 次提交
-
-
由 Timur Tabi 提交于
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of P3041DS/P5020DS ("Hydra") reference board. Signed-off-by: NTimur Tabi <timur@freescale.com> Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Wu, Josh 提交于
Signed-off-by: NJosh Wu <josh.wu@atmel.com> Acked-by: NAndreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-