- 14 10月, 2019 23 次提交
-
-
由 Igor Opaniuk 提交于
Remove legacy sdboot wrapper as distroboot can be used instead. Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>
-
由 Ye Li 提交于
Modify the SPL TEXT base from OCRAM alias to OCRAM base 0x100000, so we can use full OCRAM not limit to 96KB Signed-off-by: NYe Li <ye.li@nxp.com> Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>
-
由 Ye Li 提交于
When running SPL on iMX8, the A core starts at address 0 which is a alias to OCRAM 0x100000. The alias only map first 96KB of OCRAM, so this require the SPL size can't beyond 96KB. But when using SPL DM, the size increase significantly and may exceed 96KB. So to fix the problem, we will change SPL linker address to OCRAM address 0x100000. And then jump to the absolute address not the PC relative address for entering OCRAM. Signed-off-by: NYe Li <ye.li@nxp.com> Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>
-
由 Lukasz Majewski 提交于
This patch updates envs responsible for using USB pendrive as a SWUpdate based tool for recovery and update. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This patch converts the TPC70 to use driver model and device tree description in both SPL and u-boot proper. Notable changes (DM/DTS conversion): - PINCTRL{_IMX6} - DM_I2C - enable 'regulator' and 'pmic' commands - DM_MMC and BLK (USDHC) - DM_ETH - DM WDT (including SYSRESET) Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit adds new file - imx6q-kp-u-boot.dtsi with a set of u-boot specific properties for imx6q KP device. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit defines the TPC70 imx6q board with device tree description. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This change sets the default state of LEDs on TPC70. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This is a cosmetic change, just to use proper define instead of magic numbers. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
The TPC70 can boot from SD card (debug/development) and eMMC (production). The board_boot_order() function provides a run time check for the device from which one wants to boot (it is selected by GPIO pins setup). Moreover, a fallback to SD card is provided if the detection is not possible or working properly. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
The TPC70 can boot from eMMC's boot0. This patch allows it to update this HW partition's SPL. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Jun Nie 提交于
Support distro boot for pico imx7d in FIT image case. Signed-off-by: NJun Nie <jun.nie@linaro.org> Tested-by: NJoris Offouga <offougajoris@gmail.com>
-
由 Jun Nie 提交于
Add config to enable CAAM so that hardware random number generator works. Signed-off-by: NJun Nie <jun.nie@linaro.org>
-
由 Adam Ford 提交于
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with -u-boot.dtsi entries to include the pinmuxing in SPL, the manual code setting up the pinmux can go away. This patch removes the legacy pinmuxing code from the board file. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NFabio Estevam <festevam@gmail.com>
-
由 Adam Ford 提交于
With the 256KB of OCRAM available to SPL now, there should be enough room to enable the pinmuxing in SPL from the device tree. This patch enables SPL_PINCTRL et al and adds the serial and usdhc pin mux references to the -u-boot.dtsi file so the pins can be configured from the device tree. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NFabio Estevam <festevam@gmail.com> Reviewed-by: NPeng Fan <peng.fan@nxp.com>
-
由 Adam Ford 提交于
Since this board config only supports, the i.MX6D/i.MX6Q configurations, 256K of on-chip RAM is available which increases the space available to SPL to help further reduce board code and further enable device tree functions. This patch enables 256K of RAM. Signed-off-by: NAdam Ford <aford173@gmail.com> Reviewed-by: NFabio Estevam <festevam@gmail.com>
-
由 Soeren Moch 提交于
So we can remove lots of legacy config code. Signed-off-by: NSoeren Moch <smoch@web.de>
-
由 Soeren Moch 提交于
So we can get rid of legacy pci config code. PCI_PNP is not required for this board, remove it to reduce the size of the u-boot binary. DM_PCI does not start the host controller automatically anymore. Do so in preboot instead. Signed-off-by: NSoeren Moch <smoch@web.de>
-
由 Soeren Moch 提交于
Signed-off-by: NSoeren Moch <smoch@web.de>
-
由 Sjoerd Simons 提交于
Both the distro boot configuration as well as the general pxe support standardized on fdtfile as the variable to hold the dtb filename. Adjust to follow that such that e.g. "pxe boot" will just work. Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
-
由 Shawn Guo 提交于
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications. https://www.novtech.com/products/meerkat96.html https://www.96boards.org/product/imx7-96/ The initial supported/tested devices include: - Debug serial - SD - USB Host (with Ethernet) With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB. Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Tested-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-
由 Shawn Guo 提交于
It imports device tree source of meerkat96 board from Linux Kernel. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
- 13 10月, 2019 1 次提交
-
-
由 Tom Rini 提交于
We don't need to pull in anything from the MIPS job so exclude that from the new bcm job and make it clear it's building only ARM. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 10月, 2019 16 次提交
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-x86由 Tom Rini 提交于
- Remember the device being emulated for Sandbox PCI - Update Kconfig options for FSP 1.0 - Drop RESET_BASE and RESET_SEG_SIZE that are no longer used
-
由 Tom Rini 提交于
- Assorted cleanups - FAT bugfixes - mediatek platform updates
-
由 Tom Rini 提交于
- Various improvements to dra7xx, keystone 3, am65x SoCs - Platform updates - remoteproc improvements
-
由 Marek Szyprowski 提交于
Add support for quad (64bits) memory access specifier. Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com> Acked-by: NLukasz Majewski <lukma@denx.de>
-
由 Heinrich Schuchardt 提交于
If out of memory, return -1 and not -ENOMEM from get_contents(). Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Heinrich Schuchardt 提交于
When hitting an invalid FAT cluster while reading a file always print an error message and return an error code. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Tom Rini 提交于
At this point, all drivers that do not use CONFIG_BLK are past their migration deadlines, so remove this config as it's no longer helpful and hinders enhancing block drivers. Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Lukasz Majewski 提交于
This define indicates if DM_SPI shall be supported in SPL. This allows proper operation of DM converted SPI drivers in SPL, which use #if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted boards. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Heinrich Schuchardt 提交于
If an exception occurs in a loaded image and the relocation offset is unknown, it is helpful to know the instructions pointed to by the program counter. This patch adds the missing output. A possible output is: Code: 910c4021 aa1303e0 f9400662 d63f0040 (e7f7defb) The parentheses indicate the instruction causing the exception. The output can be disassembled using scripts/decodecode: echo 'Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)' | \ ARCH=arm64 scripts/decodecode Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb) All code ======== 0: 90000360 adrp x0, 0x6c000 4: 9100b800 add x0, x0, #0x2e 8: 94002782 bl 0x9e10 c: 17ffff8f b 0xfffffffffffffe48 10:* e7f7defb .inst 0xe7f7defb ; undefined <-- trapping instruction Code starting with the faulting instruction =========================================== 0: e7f7defb .inst 0xe7f7defb ; undefined We already have implemented the same for armv7. For testing command 'exception undefined' can be used. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 T Karthik Reddy 提交于
This patch uses auto instead of decimal in simple_strtoul(). Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Rasmus Villemoes 提交于
readb is unconditionally defined earlier in io.h, so there's no point checking whether it's undefined. Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk>
-
由 Rasmus Villemoes 提交于
No ARM board seems to define __mem_pci - and if it did, one would get tons of ./arch/arm/include/asm/io.h:307:0: warning: "readl" redefined warnings, because readl and friends are unconditionally defined earlier in io.h. Moreover, the redefinitions lack the memory barriers that the first definitions have. So I'm guessing this is practically dead code. Signed-off-by: NRasmus Villemoes <rasmus.villemoes@prevas.dk>
-
由 Mans Rullgard 提交于
This change allows setting pre-defined eMMC boot partition for SPL eMMC booting. It is necessary in the case when one wants to boot (through falcon boot) from eMMC after loading SPL from other memory (like SPI-NOR). Signed-off-by: NMans Rullgard <mans@mansr.com> [lukma: Edit the commit message] Signed-off-by: NLukasz Majewski <lukma@denx.de> Acked-by: NAndreas Dannenberg <dannenberg@ti.com>
-
由 Mans Rullgard 提交于
This fixes a wrongly indented block of code. Signed-off-by: NMans Rullgard <mans@mansr.com> [lukma: Make the commit message more verbose] Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lokesh Vutla 提交于
If there is any failure during IOdelay recalibration sequence, IOs are not guaranteed to behave as expected. So hang on any failure during the sequence. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-
由 Lokesh Vutla 提交于
When an error is reported in __recalibrate_iodelay_start(), de-isolation of IO doesn't happen. Because of this, undefined behaviour is observed on many peripherals without any error. So make sure io is out of isolation at the end of iodelay recalibration. Reported-by: NRichard Woodruff <r-woodruff2@ti.com> Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
-