Timeout interrupt also work for response busy command(R1b) like
cmd38/cmd6. So need to set it accordingly. Current code only
set timeout for data command.
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>

High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.

[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NPantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>

Starting part of device initialization sets the init_in_progress flag
only if the MMC card did not yet come to ready state and needs to continue
polling. If the card is SD or if the MMC card became ready quickly,
the flag is not set and (if using pre-initialization) the starting
phase will be re-executed from mmc_init function.

Set the init_in_progress flag in all non-error cases. Also, move flags
setting statements around so that the flags are not set in error paths.
Also, IN_PROGRESS return status becomes unnecessary, so get rid of it.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>

The polling loops in sd_send_op_cond and mmc_complete_op_cond functions
check the ready flag state at the end of the loop, that is after executing
a delay inside the loop, which, in case of exiting with no error,
is not needed. Also, one of these loops, as well as the loop
in mmc_send_status, have the delay just before exiting on timeout
conditions.

Restructure all these loops to check the respective conditions before making
a delay for the next loop pass, and to appropriately exit without the delay.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>

Some MMC cards come to ready state quite quickly, so that the respective
flag appears to be set in mmc_send_op_cond already. In this case trying
to continue polling the card with CMD1 in mmc_complete_op_cond is incorrect
and may lead to unpredictable results. So check the flag before polling
and skip it appropriately.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>

The previous change to use 'ocr' structure field for storing send_op_cond
command response also stopped using command response directly
outside of mmc_send_op_cond_iter(). Now it becomes possible to use
command structure in mmc_send_op_cond_iter() locally, removing a necessity
to pass it as an argument from the caller.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>

The 'op_cond_response' field in mmc structure contains the response
from the last SEND_OP_COND MMC command while making iterational
polling of the card. Later it is copied to 'ocr' field, designed
to contain the OCR register value, which is actually the same
response from the same command. So, these fields have actually
the same data, just in different time periods. It's easier to use
the same 'ocr' field in both cases at once, without temporary using
of the 'op_cond_response' field.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>

The version flag constant name used in IS_MMC macro is incorrect/undefined.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>

Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Move arch/arm/include/asm/arch-zynq/*
  -> arch/arm/mach-zynq/include/mach/*
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Move arch/arm/cpu/armv7/zynq/* -> arch/arm/mach-zynq/*
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The comment line in arch/arm/cpu/armv7/zynq/config.mk says that
the option "-mfpu=neon" is necessary for compiling lowlevel_init.S.
We do not have to give it to all the source files.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Enable SDHCI0 for zynqmp.
Add empty gpio.h because of sdhci requirement.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Provide an option to write filesystem independend commands.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Added the SPI driver support for ZynqMP
The controller is same as zynq SPI controller
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

Enable the i2c driver for ZynqMP
Also enable the eeprom for read and writes
to eeprom on ZynqMP
ZynqMP uses the same i2c controller as in Zynq
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add support for EMMC bootmode.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add support for Veloce - zynqmp emulation platform.
Platform doesn't support SDHCI.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Fix wrong timer calculation in get_timer_masked incase of
overflow.
This fixes the issue of getting wrong time from get_timer()
calls.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Remove the quirk SDHCI_QUIRK_NO_CD as it is not
required.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add support for loading sw for R5 with enabling for zynqmp.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>

Define the mmu table till 2MB granularity
enable dcaches for zynqmp.
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Disable all level shifters before enabling
the PS-to-PL level shifters as it would
be good to disable all level shifters before
enabling the PS-to-PL in order to ensure that
it is in proper state
Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

We are about to change the location for ps7_init files, breaking the
current work-flows.  It is good time to drop the legacy ps7_init.c/h
support.

Going forward, please use ps7_init_gpl.c/h all the time.
If you are still using old Xilinx tools that are only able to
generate ps7_init.c/h, rename them into ps7_init_gpl.c/h.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: NSören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

The PicoZed is a System-on-Module board which is marketed as part of
the ZedBoard/MicroZed/etc. collection. It includes a Zynq-7000
processor.

This patch adds support that covers all the variants of the PicoZed
including the SKUs with Z7010/Z7020 and Z7015/Z7030 Zynq chips. This
patch set however only covers support for the System-on-Module and does
not cover any extra components that are available on carrier boards
(except those that are fanned out of the module itself).

More information on this board, its variants and available carrier
boards is available at: http://zedboard.org/product/picozedSigned-off-by: NNathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

On slow platforms not all baudrate setting is valid.
Check it directly in the driver and setup maximum possible
frequency.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Enable GPIO driver and GPIO commands.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Most of the code is taken (and adapted) from Linux kernel driver.

Just add CONFIG_ZYNQ_GPIO to you config to enable it
Signed-off-by: NAndrea Scian <andrea.scian@dave.eu>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

It is possible for CONFIG_XILINX_EMACLITE to be defined without
XILINX_EMACLITE_BASEADDR being defined as the EMAC Lite driver support
OF init. Check that the driver is enabled and the base address is
available before initializing with a static base address.
Signed-off-by: NNathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

These functions now rely on uclass_find_first/next_device() and assume that
they will either return failure (-ve error code) or a device. In fact,
coming to the end of a list is not considered failure and they return 0
in that case.

The logic to deal with this was replaced in commit acb9ca2a with just using
uclass_get_device_tail(). Add back the missing logic. This bug was
caught by unit tests but since they were broken for other reasons at the
time, this was not noticed.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This was accidentally added by commit dd0b0122
"serial: ns16550: Add an option to specify the debug UART register shift".
Remove it.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Trivial bug fix for commit 5a87c417 (dm: core: Drop device
removal error path when not supported).
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.

Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000

=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK
Signed-off-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reported-by: NBin Meng <bmeng.cn@gmail.com>
Tested-by: NBin Meng <bmeng.cn@gmail.com>

With SPI flash moving to driver model, commit fbb09918 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.

This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NJagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>