- 10 1月, 2017 19 次提交
-
-
DNL numbers are not changed that's why fastboot needs to be called with -i parameter (Xilinx vendor id). - Show available devices sudo fastboot -i 0x03fd devices xilinx_zynqmp_zcu100 fastboot - Stop fastboot and go back to U-Boot prompt sudo fastboot -i 0x03fd continue - Reboot the board sudo fastboot -i 0x03fd reboot - Get internal variables sudo fastboot -i 0x3fd getvar bootloader-version bootloader-version: U-Boot 2016.07-00026-g19bd53044817 sudo fastboot -i 0x3fd getvar downloadsize downloadsize: 0x06000000 sudo fastboot -i 0x3fd getvar version version: 0.4 (regular variables needs to have fastboot. prefix - there is also serialno variable which should be define as serial#) - Format SD/MMC/EMMC card sudo fastboot -i 0x3fd oem format - Write images to boot and Linux partition sudo fastboot -i 0x3fd flash boot sd.img sudo fastboot -i 0x3fd flash Linux os.img - Creating sd.img or os.img $ dd if=/dev/zero of=sd.img bs=1024 count=1024 $ mkfs.vfat sd.img $ mkdir sd-mount $ mount -o loop sd.img sd-mount $ echo foo > sd-mount/bar $ umount sd-mount partitions setting should be checked by running gpt command. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Stefan Krsmanovic 提交于
Added the idle-states node to describe zynqmp idle states. Only cpu-sleep-0 idle state is added in this patch. References to the idle-states node are added in all CPU nodes. Time values: entry/exit latencies and min-residency, needs to be tuned. arm,psci-suspend-param is selected to comply with PSCIv1.0 and Extended StateID format. Signed-off-by: NStefan Krsmanovic <stefan.krsmanovic@aggios.com> Acked-by: NWill Wong <willw@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Fix DT binding for usb nodes. Setup correct aliases and enable dwc3 nodes. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Just sync between version. Others zynqmp boards have this setup. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Shubhrajyoti Datta 提交于
The watchdog clock node is missing. Add the same. This solves the below error. cdns-wdt fd4d0000.watchdog: input clock not found cdns-wdt: probe of fd4d0000.watchdog failed with error -2 Signed-off-by: NShubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Sudeep Holla 提交于
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: NSudeep Holla <sudeep.holla@arm.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
modeboot variable is used for saving inforation which bootmode is used. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
spi-max-frequency for spi bus depends on devices which are connected to it. Remove this parameter from dtsi file. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Do the same change which was done in ZynqMP by: "ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP" (sha1: a8b6a156) Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Enable CONFIG_SYS_TEXT_BASE via Kconfig. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Xilinx core files will take care about it. There is no need to have these functions because they do nothing. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Add support to save environment as a file of FAT filesystem on to SD card. The file will be saved with name uEnv.txt. This environment will be retrieved during boot. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Increase environment size to 32K as the current default environment itself is greater than 4K. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Enable overwriting variables out of main config file. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
IP addresses shouldn't be hardcoded in board config. This patch removes them. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Sai Pavan Boddu 提交于
Add a prompt for editing in menuconfig Signed-off-by: NSai Pavan Boddu <saipava@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Using generic wait_for_bit() implementation instead of using private wait function. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
wait_for_bit() is missing reset watchdog in case watchdog is configured. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 1月, 2017 2 次提交
-
-
由 Ladislav Michl 提交于
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 1月, 2017 3 次提交
-
-
由 Jagan Teki 提交于
Add 'Peng Fan' as MAINTAINERS of configs/mx6ull_14x14_evk_plugin_defconfig which is missing in below commit "imx: mx6ull_14x14_evk: add plugin defconfig" (sha1: b90ebf49) Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: NPeng Fan <peng.fan@nxp.com> Signed-off-by: NJagan Teki <jagan@openedev.com>
-
由 Andrew F. Davis 提交于
The SPL load address changes based on boot type in HS devices, ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs for similar reasons. Add this same logic for AM33xx devices. Also make the default value for ISW_ENTRY_ADDR correct for GP devices based on SoC, HS devices already pick the correct value in their defconfig. Signed-off-by: NAndrew F. Davis <afd@ti.com>
-
由 Andrew F. Davis 提交于
When TI_SECURE_DEV_PKG is not defined we warn that the file '*_HS' was not generated but generate an unsigned one anyway, first fix this warning to say that it was generated but not secured. When the user then exports TI_SECURE_DEV_PKG after getting this warning, and tries to re-build, 'make' will detect the build artifacts as unchanged and so assume they do not need to be re-generated. This causes it to fail to sign the files and it will pack unsigned files into the final image, even though TI_SECURE_DEV_PKG is now correctly defined and working. Fix this by using FORCE on the targets causes them to be re-run even if the dependent files have not changed. This then causes another issue. We currently rename the signed dtb files to overwrite the non-signed ones. We do this so the 'mkimage' tool gives the packaged dtb sections the correct name. If we do not rename the files then SPL will not find them during boot. Fix this by renaming the dtb files by appending _HS to the end of the filename, after the ".dtb", this causes them to still be named correctly in the FIT blob. Signed-off-by: NAndrew F. Davis <afd@ti.com>
-
- 05 1月, 2017 16 次提交
-
-
-
-
由 York Sun 提交于
Use Kconfig option SYS_PPC64 instead. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Use Kconfig option to select chassis version. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Use Kconfig option E6500 and clean up existing usage. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
After most config options are moved to Kconfig, the unused ifdef or elif can be removed. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Use Kconfig to select DDR version instead of using config header. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
These two macros are used for the same thing, the total number of DDR controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and merge existing usage. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing usage in ls102xa and fsl-layerscape. Remove all powerpc macros in config header and board header files. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Use Kconfig to select errata workaround. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13, SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig. Move existing macros to related Kconfig. Signed-off-by: NYork Sun <york.sun@nxp.com> [trini: Migrate bk4r1] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 York Sun 提交于
Use Kconfig to select errata workaround. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Create driver/ddr/fsl/Kconfig and move existing options. Clean up existing macros. Signed-off-by: NYork Sun <york.sun@nxp.com> [trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 York Sun 提交于
Remove this macro. It was added by e622d9ed but actually wasn't used. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Use TARGET_T2081QDS from Kconfig instead. Signed-off-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
Use TARGET_T2080RDB from Kconfig instead. Signed-off-by: NYork Sun <york.sun@nxp.com>
-